Page 1
NATURAL WOOD
WISHING WELL
ASSEMBLY INSTRUCTIONS
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
90792 Wishing Well.p65 11/20/03, 12:36 PM1
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
For technical questions please call 1-800-444-3353
Page 2
SPECIFICATIONS
Item Description
Construction
Overall Dimensions
Well Outer Dimensions
Inside Dimensions
Net Weight
Fir Wood with Natural Finish
22-1/8"L X 22-1/8" H
22-1/8"Diameter X 13-5/8"High
17-5/8" Diameter X 11-7/8" Deep
16.6 Lbs.
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1. KEEP PRODUCT ASSEMBLY AND DISPLAY AREAS CLEAN. Cluttered areas
invite injuries. Assemble and display product on flat, level surface such as carpet or
grass.
2. KEEP CHILDREN AWAY FROM PRODUCT. Do not allow children to handle or
climb upon this product. This is not a toy. It is a decorative item only. Place in an
area where tipping over the Wishing Well will be prevented.
3. DO NOT ATTEMPT TO ASSEMBLE THIS PRODUCT IF UNDER THE INFLU-
ENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to
determine if your judgement or reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to assemble this product.
4. USE EYE PROTECTION. Wear ANSI approved safety impact goggles when
assembling this product. Goggles are available from Harbor Freight Tools.
5. CHECK FOR DAMAGED PARTS. Before using this product, carefully check for
damaged parts and any other conditions that may affect its operation. Replace or
repair damaged or worn parts immediately.
6. REPLACEMENT PARTS AND ACCESSORIES. When repairing, use only identical
replacement parts.
7. AVOID SHARP EDGES WHEN ASSEMBLING. Cut wood may have splinters
within. Also, some of the mounting hardware may have sharp points.
9. NOT INTENDED TO HOLD WATER.
SKU 90792 PAGE 2
90792 Wishing Well.p65 11/20/03, 12:36 PM2
Page 3
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 5) are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
We suggest you assemble the unit on a soft, clean surface to avoid damage to the finish.
ASSEMBLY OF WISHING WELL
1. Join the Vertical Supports (7 & 8) with the Screws (1) and Nuts (6) in two places each. This
will make two Vertical Support assemblies. See Figure A.
2. On the outer side of Well Base (10), insert Bolts (3) on each side so they show on the inside
of the Well Base. See Figure A.
Vertical
Support
Assembly
Part 7
Part 1
& 6
Part 3
Part 8
A
Part 9
Part 10
Figure A
Figure B
3. Insert the Spindle (9) into the large holes near the top of the Vertical Supports (7) (left and
right). You do this by pressing the Wooden Locking Pin (A) at the end of the Spindle (9) into
the holes near the top of the Vertical Supports (7). See Figure A & B.
SKU 90792 Page 3
90792 Wishing Well.p65 11/20/03, 12:36 PM3
Page 4
4. Lift the assembled Vertical Supports (7 & 8) (right and left), with the Spindle (9) in place.
Place assembly inside the Well Base (10). Align the two holes in each of the lower Vertical
Supports (8) over the Bolts (3) which should be protruding on the inside of the Well Base,
using assistance if neccessary. Use Nuts (6) on the Bolts (3) and tighten Nuts inside of the
Well Base. See Figure C
Note: If the predrilled holes are not drilled all the way through the wood, use a drill to clear them.
5. Secure the Rooftop with Support (11 & 12) to each of the Vertical Supports (7) (right and
left), using Bolts (2) and Nuts (6). Tighten Nuts and Bolts securely. If Rooftop is not
preassembled with Slats (15), use Woodscrews (4) to assemble. See Figure D.
6. Gently tap the Crank (13) onto end of the Spindle at the Wooden Locking Pin (A) with a
hammer (hammer not included). See Figure E.
7. Tie Rope (16) around handles of Bucket (14). Staple other end of Rope onto Spindle (9)
securely. (Staple Gun not included). Wrap Rope around Spindle several times so the Bucket
is visible and not resting on the bottom of the Wishing Well Base. See Figure C and E.
Part 7
Part 8
Part 10
Figure C
Part 16
Part 9
Part 15
Part 14
Part 12
Part 11
Part 2 & 6
Figure D
A
SKU 90792 PAGE 4
90792 Wishing Well.p65 11/20/03, 12:36 PM4
Part 13
Part 16
Figure E
Page 5
PARTS LIST
PART# DESCRIPTION QTY
1
2
3
4
5
6
6 X 50
6 X 55
6 X 45
4 X 30
4 X 20
Nut
4
2
4
18
1
10
PARTS IDENTIFICATION
Part 12
Part 7
PART # DESCRIPTION QTY
7
8
9
10
11
12
13
14
15
16
Vertical Support (top)
Vertical Support (bottom)
Spindle
Well Base
Rooftop with Support (Right)
Rooftop with Support (Left)
Crank
Bucket
Slats
Rope
Part 11
Part 15
2
2
1
1
1
1
1
1
8
1
Part 1 & 6
Part 8
Part 14
Part 10
Part 16
Part 3
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry at
all times.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 90792 PAGE 5 REV 11/03
90792 Wishing Well.p65 11/20/03, 12:36 PM5
Loading...