Harbor Freight Tools 69721 Product manual

READ AND SAVE THESE INSTRUCTIONS.

RULES FOR SAFE OPERATION

1. WARNING! To reduce the risk of fire or
electric shock, do not use this blower with
any solid-state speed control device.

2. This appliance has a polarized plug
(one blade is wider than the other).
To reduce the risk of electric shock, this
plug is intended to fit into a polarized outlet
only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician.
Do not change the plug in any way.
Do not attempt to defeat this safety feature.

3. Do not leave blower running
while unattended.

4. Do not operate any blower with a
damaged cord or plug. Discard blower
or return to an authorized service
facility for examination and/or repair.

5. Do not run cord under carpeting.
Do not cover cord with throw rugs,
runners, or similar coverings. Arrange
cord away from traffic area and
where it will not be tripped over.

6. Never insert fingers, pencils, or any other
object through Front or Rear Blade Guards.

7. Disconnect blower when moving it
from one location to another.

8. Disconnect blower before
removing grills for cleaning.

9. Be sure blower is on a stable surface
when operating to avoid overturning.

10. DO NOT use blower in window.
Rain may create electrical hazard.

11. Maintain labels and nameplates on the blower.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

12. Use only in dry areas.
Do not use in bathrooms, laundry area,
near sinks or other sources of water.

13. This blower is not a toy.
Keep it out of reach of children.

14. WARNING: Handling cord on this blower
will expose you to lead, a chemical known
to the State of California to cause cancer,
and birth defects or other reproductive harm.
Wash hands after handling.
(California Health & Safety Code

§ 25249.5, et seq.)

15. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all conditions and situations that may
occur. It must be understood by operator
that common sense and caution are factors
which cannot be built into this blower,
but must be supplied by operator.

Page 2 For technical questions, please call 1-800-444-3353. Item 69721

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

Indicates a hazardous situation which, if not avoided,

Indicates a hazardous situation which, if not avoided,

Addresses practices not related to personal injury.

Specifications

Electrical Rating 120V~ / 60Hz / 1.5A

Maximum Air Flow 300 CFM

will result in death or serious injury.

could result in death or serious injury.

could result in minor or moderate injury.

220633

Page 3For technical questions, please call 1-800-444-3353.Item 69721

Operation

Read the ENTIRE RULES FOR SAFE OPERATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this blower.

1. Make sure the blower’s Speed Control

is in the ″OFF″ position.

2. Plug the Power Cord into a
GFCI-protected outlet.

3. Position the blower as desired.
It can rest on different Pads to
direct the airflow at different angles.
It must rest on a level, firm base.

4. Leave adequate space around the blower
for unimpeded air flow. Air flows in at the
sides of the blower. Do not allow dirt or

debris to be drawn into the blower.

5. Rotate the Speed Control to the desired speed
setting. To turn the blower OFF, rotate the

blower’s Speed Control to the ″OFF″ position.

Note: If blower suddenly stops operating,

the Overload Protection may have tripped.
Make sure that the blower is dry, that the
vents are not obstructed, and that the blower
has cooled completely before pressing the
Reset Button and continuing to use the blower.

6. Additional powered devices can be plugged
into the 120V~ outlets on the sides of the
blower. Do not exceed 13A combined

current draw across the two outlets.

Air

Outlet

Reset

Button

Figure A: Controls - top view

Speed Control

Handle

120V~
Outlet

7. To prevent accidents, turn off the blower
and unplug it after use. Clean, then store
the blower indoors out of children’s reach.

Air

Inlet

Pads

Figure B: Additional Components

Page 4 For technical questions, please call 1-800-444-3353. Item 69721

User Servicing Instructions

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK:
Turn the Power Switch of the blower off, unplug the blower from its
electrical outlet, and allow the blower to cool completely before performing
any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM BLOWER FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs,
have the problem corrected before further use.

1. BEFORE EACH USE, inspect the general
condition of the blower. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

2. Clean outside housing regularly.
Use damp cloth during cleaning and
dry before use. Do not open housing

for cleaning or any other reason.

3. WARNING! If the supply cord of this
blower is damaged, it must be replaced
only by a qualified service technician.

If blower suddenly stops operating

The Overload Protection may have tripped.

Before pressing the Reset Button and continuing to use the blower, make sure:

• that the blower is dry,

• that the vents are not obstructed, and

• that the blower has cooled completely.

Page 5For technical questions, please call 1-800-444-3353.Item 69721

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Part Description Qty

1 Motor 1
2 Capacitor 1
3 Mounting Ring 1
4 Fan Wheel 1
5 Right Housing 1
6 Left Housing 1
7 Corner Pad 2
8 Slight Corner Pad 4
9 Straight Pad 4

10 Power Receptacle 2

Record Serial Number Here:

Note: If blower has no serial number,

record month and year of purchase instead.

Part Description Qty

11 Speed Control Knob 1
12 Power Switch 1
13 Strain Relief 1
14 Handle 1

Overload Protection

15

/ Reset Button
16 Nut 1
17 Grill 1
18 Power Cord 1

Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.

1

Page 6 For technical questions, please call 1-800-444-3353. Item 69721

9

10

Assembly Diagram

8 7

11

13

12

56

17

161514

10

18

4

3

2

1

Page 7For technical questions, please call 1-800-444-3353.Item 69721

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]