Harbor Freight Tools 69643 Owner's Manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

ITEM 69643

Visit our website at: http://www.harborfreight.com

Email our technical support at: tech@harborfreight.com

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 4

Setup .......................................................... 4

SAFETY OPERATION MAINTENANCESETUP

Operation .................................................... 6

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Maintenance ............................................... 9

Parts List and Diagram .............................. 10

Warranty .................................................... 12

WARNING SYMBOLS AND DEFINITIONS

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. Keep installation area clean. Cluttered

areas invite accidents.

2. Observe installation area conditions. Keep work area well lit during installation.

3. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. Do not use the Security Light if any switch does not turn on and off properly.

4. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty.

5. Check hardware and assembled parts after assembling. All connections should be tight and hardware tightened.

6. Keep children away. Mount the Light, Solar Panel, and Cord out of children’s reach.

Page 2 For technical questions, please call 1-800-444-3353. Item 69643

7. Dress properly. Protective, electrically non- conductive clothes and nonskid footwear are recommended when working with the Solar Powered Security Light. Wear restrictive hair covering to contain long hair.

8. Use eye protection. Wear ANSI-approved impact safety goggles when setting up this product.

12. NiCd BATTERY MUST BE RECYCLED

OR DISPOSED OF PROPERLY. Do not short, incinerate or open battery.

13. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the

safety of the power tool is maintained.

9. Maintain products with care. Keep the Solar Powered Security Light clean for better and safer performance. Inspect the Light periodically. If damaged, have it repaired by a qualified technician.

10. Do not overreach. Keep proper footing and balance at all times. If a ladder is to be used during installation, it should be supported by an assistant.

11. Do not set up the Solar Powered Security Light if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not set up the Light.

SAVE THESE INSTRUCTIONS.

14. WARNING: Handling the cord on this product’s Charger will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)

15. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAFETYOPERATIONMAINTENANCE SETUP

Page 3For technical questions, please call 1-800-444-3353.Item 69643

Specifications

Lamp 60 Super Bright White LEDs

Battery Pack 6V, 900mAh, NiCd Battery Pack

SAFETY OPERATION MAINTENANCESETUP

Solar Panel 6-1/4" x 5" Amorphous Solar Panel

Detects Motion Up to 50'

Range of Motion Up to 120°

Delay Time 5 to 120 Seconds (adjustable)

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to Parts List and Diagram on page 10.

Installation

1. Decide where you want to place the Lamp and the Solar Panel. The Solar Panel is equipped with a 16 ft. connecting wire, so the Lamp and Solar Panel can be installed up to 16 ft. apart. The Solar

Panel must be set in a location that receives full, direct sunlight, a minimum of eight hours a day. Ideally, the solar panel should be angled slightly toward the south (northern hemisphere).

2. Mount the Solar Panel:

a. Place the Solar Panel in the desired location,

adjusting the unit to best fit the surface.

b. Mark the hole locations of the Base,

then set the Solar Panel aside.

c. Check that the marked areas are clear of

obstacles such as cables and electrical lines. Drill holes for the enclosed Screws and plastic Anchors.

d. Insert the plastic Anchors then secure the

Solar Panel in place with the screws.

3. Mount the Lamp:

a. Locate the unit six to eight feet above ground

on a solid surface capable of supporting the Lamp and secure enough so that it will not move when exposed to vibrations or wind. The unit must be high enough to allow for motion detection and light distribution.

b. Mark the hole locations of the Mounting

Bracket, then set the Lamp aside.

c. Check that the marked areas are clear of

obstacles such as cables and electrical lines. Drill holes for the enclosed Screws.

d. Secure the Lamp in place with the screws.

4. Carefully route the Power Cord of the Solar Panel to the Lamp and plug it into the Battery Housing Outlet on the back of the Battery Housing.

5. Loosen the Detector Angle Lock, swivel the Motion Detector Head so that it faces the area where movement will occur, and tighten the Detector Angle Lock.

Page 4 For technical questions, please call 1-800-444-3353. Item 69643

+ 8 hidden pages