Harbor Freight Tools 69302, 69305 Owner's Manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.

ITEM 69302 / 69305

SHALLOW WELL
PUMP

Visit our website at: http://www.harborfreight.com

Email our technical support at: [e-mail]

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

Copyright© 2011 by Harbor Freight Tools®. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

ITEM 69305ITEM 69302

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

WARNING

IMPORTANT! For your own safety –
before starting to run the pump, please have
the following items checked by an expert:

1. Risk of electric shock – This pump is supplied
with a grounding conductor and grounding-type
attachment plug. To reduce the risk of
electric shock, connect only to a properly
grounded, grounding-type receptacle.

2. Risk of electric shock – This pump has not been
investigated for use in swimming pool areas.

3. The electrical connections must be
protected from moisture.

4. If there is danger of flooding, the electrical
connections must be taken to higher ground.

5. Circulation of caustic fluids, as well as the circulation
of abrasive materials, must be avoided at all costs.

Grounding Instructions

6. The pump must be protected from frost.

7. The pump must be protected from running dry.

8. Access by children should also be
prevented with appropriate measures.

9. WARNING: Handling the Power Cord
on this product will expose you to lead,
a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

10. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by
the operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:

Check with a qualified electrician if you
are in doubt as to whether the outlet is
properly grounded. Do not modify the

power cord plug provided with the tool.
Never remove the grounding prong from the plug. Do
not use the tool if the power cord or plug is damaged.
If damaged, have it repaired by a service facility
before use. If the plug will not fit the outlet, have a
proper outlet installed by a qualified electrician.

Grounding

Pin

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

2. The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding
system and must never be attached to an electrically
“live” terminal. (See 3-Prong Plug and Outlet.)

3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance with
all codes and ordinances. The plug and outlet should
look like those in the preceding illustration.

(See 3-Prong Plug and Outlet.)

4. This pump is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 V~ 3-Prong Plug and Outlet. The pump has
a grounding plug that looks like the plug illustrated
above in 125 V~ 3-Prong Plug and Outlet.

5. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.

6. Do not use extension cords with this pump.

1.

Tools marked with “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock. (See 3-Prong Plug and Outlet.)

Page 2 For technical questions, please call 1-800-444-3353. Item 69302 & 69305

7. Do not use an adapter to connect
this pump to a different outlet.

Specifications

Model 69302 69305

Electrical Rating

120V~ 60Hz

4.5A
Inlet / Outlet Diameter 1 IN. NPT
Maximum Flow 920 GPH
Maximum Suction Lift 26 FT.
Maximum Delivery Height 98 FT.
Pump Body Material Stainless Steel Cast Iron
Air Bladder Pressure 23 PSI
Start Pressure 20 PSI
Stop Pressure 35 PSI
Power Cord Length 6 FT.

120V~ 60Hz

4.5A

NOT FOR POTABLE WATER.

Note: Performance of this pump (if powered by line voltage) may vary depending on variations

in local line voltage. Extension cord usage may also affect pump performance.

Before start-up, note the following: The pump can be connected to any shock-proof plug which has
been installed according to regulations. The plug must have a supply voltage of 120V~, 60Hz.

CAUTION: This pump has been evaluated for use with water only.

Fluid Type: The Pump is designed for use with water with a maximum temperature of 77° F (25° C).

Do not use the pump for other fluids, especially not fuels, cleaning fluids, or other chemical products.

Components

Priming

Inlet

Intake

Discharge

Pressure

Gauge

Air

Valve

(hidden)

Intake

Pressure

Gauge

Priming

Inlet

Discharge

Air

Valve

(hidden)

Figure A: 69302 Components

Figure B: 69305 Components

Page 3For technical questions, please call 1-800-444-3353.Item 69302 & 69305

Installation

The well motor pump must be installed in a stationary position with a fixed pipeline and a steady water supply.

Please note!

1. Do not install the pump by suspending
it unsupported from its delivery pipe.
The pump must be placed on the bottom of the shaft.

Power Supply

1. The pump is equipped with a shock-proof plug
according to regulations. The pump is designed
to be connected to 120V~, 60Hz safety socket.

2. Make sure that the socket is sufficiently
secured and is in excellent condition.

Installation Considerations

This pump is designed for use as a well pump.

WARNING! TO PREVENT SERIOUS INJURY
FROM ELECTRIC SHOCK:

Install indoors or in weather-proof well house only.
This Pump is non-submersible.
Do not plug in the power cord when wet
or standing on damp or wet ground.
Do not plug in the power cord until instructed to do so.

NOTE:

a. ONLY pump clean water.

b. Additional components (such as valves and pipes)

may be required for installation, but not included.

c. Installation requires skilled workmanship

and compliance with local building codes.

If you are not confident in your ability to
properly and safely install this pump, have a
qualified technician perform the installation.

d. The water to be pumped must be clean and

must be free of sand and grit, which would
damage the pump and void the warranty.

2. The pump must be installed with an automatic
float switch (not included) to prevent running dry.

3. When the plug is inserted into the socket
the pump will be on standby.

WARNING! If the power cord or plug is damaged,
do not use the pump. The power cord or plug
may only be repaired by a certified electrician.

1. The illustration below shows an example of a proper
shallow well pump installation. The total suction lift
(vertical well lift + length of off-set line) must
not exceed Maximum Suction Lift.

Outlet Water

Level

To

Household

Check

Valve

Length of off-set line

(Add when calculating total

suction lift due to friction.)

SLOPE SLIGHTLY DOWNWARD TO WELL

Water

System

Shallow

Head

Well Pump

Well
Seal

Standing Water Level

(With Well Pump Off)

Pumping Water Level (with Well Pump Operating)

Vertical Well Lift

Foot

Valve

Figure C: Pump Setup Example

Note: This pump is intended for shallow well application

only and is not intended to be used as a booster pump.

Note: For optimal performance, install the pump
as close to the well head as possible.

2. Install a Foot Valve at the bottom of
the suction pipe. The Foot Valve must be
under the Pumping Water Level, the level that
the water falls to when the pump operates.

Page 4 For technical questions, please call 1-800-444-3353. Item 69302 & 69305