Harbor Freight Tools 69148 Owner's Manual
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
1,000 LB.
HYDRAULIC TABLE CART
Visit our website at: http://www.harborfreight.com
Email our technical support at: tech@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Copyright© 2011 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
ITEM 69148
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety ......................................................... 3
Specifications ............................................. 4
Setup .......................................................... 4
SAFETY OPERATION MAINTENANCESETUP
Operation .................................................... 5
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Maintenance ............................................... 7
Parts Lists and Diagrams ........................... 8
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Page 2 For technical questions, please call 1-800-444-3353. Item 69148
IMPORTANT SAFETY INFORMATION
Hydraulic Cart Safety Warnings
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed listed weight capacity.
Be aware of dynamic loading! Sudden
load movement may briefly create excess
load causing product failure.
3. Lock Casters when unattended.
4. Be aware of pinch points. Keep hands and feet
clear of the lifting mechanism during operation. The
Scissor Arm Assembly (151) can cause serious
injury when opening or closing. Do not allow anyone
near the Scissor Arm Assembly during operation.
5. Use only on a flat, stable, hard surface.
6. Do not make any alterations to this product.
7. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
8. Keep clear of load while lifting and lowering.
9. Lower load slowly.
10. Inspect before every use; do not use
if parts are loose or damaged.
11. The brass components of this product contain lead,
a chemical known to the State of California to cause
cancer, birth defects (or other reproductive harm).
(California Health & Safety code § 25249.5, et seq.)
12. Before first use, check hydraulic fluid level and fill
to the top of the fill port as described on page 5.
Place the Table Assembly on a flat surface which
is well lighted and safe for assembly operation..
Thoroughly test the Lift Table for proper operation.
13. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
14. This product is not a toy.
Keep it out of reach of children.
15. Do not use for aircraft purposes.
16. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAFETYOPERATIONMAINTENANCE SETUP
SAVE THESE INSTRUCTIONS.
Page 3For technical questions, please call 1-800-444-3353.Item 69148
Specifications
Lift Capacity 1,000 lb.
SAFETY OPERATION MAINTENANCESETUP
Table Height
Table Dimensions 33" L x 20" W
Casters
Minimum: 11"
Maximum: 34-1/2"
5" D x 2" W,
(2 swivel with brakes, 2 fixed without brakes)
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following
pages, refer to Parts Lists and Diagrams on page 8.
Assembly/Mounting
1. Place the Table Assembly on a flat surface which
is well lighted and safe for assembly operation.
2. Unfold the Handle (101) by pulling it up and back into
a vertical position. Be sure that the Handle locks into
position. The Handle may be released and folded
back down by pressing down the Locking Bar (117).
Functions
Handle (101)
Table (141)
3. Install the Pump Lever/Foot Pedal (139/140)
assembly into the Connecting Rod (133) and
secure in place using the Bolt (135).
Control Lever (102)
Pump Lever/
Foot Pedal
(139/140)
Locking Bar (117)
Locking Swivel Caster (118)
Figure A
Page 4 For technical questions, please call 1-800-444-3353. Item 69148
Loading...