![](/html/0a/0af4/0af46a3a877144df0f9fb2f5d1e28335484ea365b19d5a790d7b92e44dec03f9/bg1.png)
Foldable/Adjustable
Sawhorse
Item 69059
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Email our technical support at:
tech@harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call 1-800-444-3353
as soon as possible.
Copyright© 2007 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight
Tools. Diagrams within this document may
not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions,
please call 1-800-444-3353.
Specications
Weight Capacity 440 LB.
Height Adjustment
Range
25-3/8 IN. to 35-7/8 IN.
Manual Revised 11j
![](/html/0a/0af4/0af46a3a877144df0f9fb2f5d1e28335484ea365b19d5a790d7b92e44dec03f9/bg2.png)
Important Safety Information
Operating Instructions
1. Do not stand or sit on Sawhorse.
2. Do not exceed the maximum weight
capacity of 440 lb. Be aware of
dynamic loading! Sudden load
movement may briey create excess
load causing product failure.
3. Make sure Leg Locks are secured
in Leg Holes before using.
4. Make sure Legs are the same
height before using.
5. Always wear ANSI-approved
safety goggles and heavy-duty
work gloves during use.
6. Use on hard, at surface that is
capable of supporting weight of
Sawhorse and workpiece.
7. Inspect before each use.
Do not use if damaged.
8. This product is not a toy.
Keep it out of reach of children.
9. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
10. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section
at the beginning of this
document including all text under
subheadings therein before set up or use
of this product.
1. Lay the Sawhorse face down on
the ground or workbench.
2. Unfold Legs (1) on right side and
spread them as far as they will open.
3. Unfold the Legs on the left side
and spread them also.
4. Unfold the Support Brace (8)
from one Leg to the other.
This will help stabilize the Legs.
5. Tighten the Wing Bolt (7) on each end
of Support Brace to secure it in place.
6. Carefully turn the Sawhorse over
so it is standing on the four Legs.
7. Loosen the Wing Bolt and push on
the Spring Loaded Leg Lock (12)
that holds each leg in position.
8. Adjust the Leg Extension
Tube (10) as needed.
9. Release the spring-loaded
Leg Lock so that it enters one
of the twelve positioning holes
in the Leg Extension Tube.
10. Set each Leg to the same height.
11. Tighten Wing Bolts located
on each Leg.
12. When nished, fold the Legs into
the Top (5) by reversing steps 1
through 5 above. The Sawhorse
will then be ready for storage.
NOTE: The Sawhorse has a
Handle (6) on one side for carrying.
Page 2 For technical questions, please call 1-800-444-3353. SKU 69059