WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Work Area
1. Keep your work area clean and well lit.
Cluttered dark areas invite accidents.
2. The work area should have adequate
drainage to reduce the possibility of
a fall due to slippery surfaces.
3. Keep bystanders, children, and visitors
away while operating the Sprayer.
Distractions can cause you to lose control.
Personal Safety
1. Follow all guidelines regarding
chemicals sprayed, including MSDS
instructions and EPA regulations.
2. Stay alert. Watch what you are doing and use
common sense when operating the Sprayer.
Do not use the Sprayer while tired or under
the influence of drugs, alcohol, or medication.
A moment of inattention while operating the
Sprayer may result in serious personal injury.
3. Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair and
clothing away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
4. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enable better
control of the tool in unexpected situations.
5. Always wear eye protection.
Wear ANSI-approved safety goggles.
Page 2 For technical questions, please call 1-800-444-3353. Item 61280/61281
Use
1. Use only for water or water-based fertilizers,
herbicides, pesticides and sealers. Do not use
to spray combustible or corrosive chemicals.
2. Release pressure in Tank by pulling up
on the Pressure Release Valve before
loosening or removing parts. Contents are
under pressure and may spurt forcefully.
3. Do not point the Sprayer at yourself,
other people or animals.
4. Do not allow access to treated
areas by people or animals.
5. Industrial applications must follow
OSHA requirements.
6. Make sure the liquid used in the
Sprayer is not dirty or sandy.
Service
7. This product is not a toy. Do not allow
children to play with or near this item.
8. Use as intended only.
9. Inspect before every use; do not use
if parts are loose or damaged.
10. Before filling, pull up on Pressure Release Valve to
ensure that it operates properly and does not stick.
11. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
12. The warnings and cautions discussed in this
manual cannot cover all possible conditions
and situations that may occur. The operator
must understand that common sense and
caution are factors that cannot be built into this
product, but must be supplied by the operator.
1. Have your Sprayer serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of
the tool is maintained.
SAVE THESE INSTRUCTIONS.
Specifications
Tank Capacity 2 gallons 1.25 gallons
Hose Length 4' 4'
Maximum Output 45 PSI 45 PSI
2. Store idle tools and equipment out of
reach of children and other untrained
people. Tools and equipment are dangerous
in the hands of untrained users.
3. Maintain the Sprayer with care. Keep
this product clean. A properly maintained
Sprayer is easier to control.
61281 61280
Page 3For technical questions, please call 1-800-444-3353.Item 61280/61281
Components and Controls
Handle
Release Valve
(not shown)
Trigger
Shoulder
Strap
Pressure
Wand
Funnel
Top
Hose
Tank
Nozzle
Figure A
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Assemble Wand:
a. Loosen Wand Nut, then slide Wand
into Trigger Handle Assembly.
b. Tighten Wand Nut securely.
Nozzle
(not
shown)
Wand
Wand
Nut
Figure B
Trigger
Handle
Assembly
2. Attach Shoulder Strap: Attach Rings
to Shoulder Strap holes.
Ring
Shoulder
Strap holes
Figure C
Ring
Page 4 For technical questions, please call 1-800-444-3353. Item 61280/61281
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Inspect Sprayer before use, looking for damaged, loose, and missing parts.
If any problems are found, do not use Sprayer until repaired.
Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations.
Release pressure in Tank by pulling up on the Pressure Release Valve before loosening
or removing parts. Contents are under pressure and may spurt forcefully.
1. Before filling, pull up on Pressure Release Valve to
ensure that it operates properly and does not stick.
2. Making sure the Handle Assembly is all the
way down into the Tank, turn the Handle
Assembly counterclockwise to loosen it, then
pull the Handle Assembly out of the Tank.
Figure D: Handle Assembly
3. Pour the liquid, through a strainer (sold
separately), into the Funnel Top.
Note: Fill the Tank no higher than Max. fill line.
4. Insert the Handle Assembly all the way
down into the Tank and turn the Handle
Assembly clockwise to tighten it securely.
5. Pump the Handle to build up sufficient
pressure. Once the Sprayer is pressurized
(as indicated by increased tension on
the Handle), discontinue pumping.
6. Point the Nozzle toward the area to be sprayed,
then depress the Trigger to begin spraying.
Note: Turn Nozzle to adjust spray pattern.
7. For continuous spray, press the Trigger down
and forward until it locks, then release the
Trigger. To stop continuous spray, press
down and pull back on the Trigger.
Trigger
(Locked)
Trigger
(Unlocked)
Figure E
8. As you spray, the Sprayer will depressurize.
When decreased pressure is affecting spray
pattern, pump the Handle until proper pressure
is achieved, then resume spraying.
9. To refill the Tank, pull up on the Pressure
Release Valve and remove the Handle
Assembly. Then add liquid and replace the
Handle Assembly. Pump the Handle until proper
pressure is achieved, then resume spraying.
10. When finished spraying:
• Depressurize the Tank.
• Dispose of liquid.
• Clean the Sprayer according to
Maintenance Instructions.
Page 5For technical questions, please call 1-800-444-3353.Item 61280/61281
Inspection, Maintenance, and Cleaning
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
Do not use damaged equipment. If abnormal noise, vibration, or
leaking air occurs, have the problem corrected before further use.
Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations.
Release pressure in Tank by pulling up on the Pressure Release Valve before loosening
or removing parts. Contents are under pressure and may spurt forcefully.
1. BEFORE EACH USE, inspect the general
condition of the Sprayer. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
Troubleshooting
Problem Possible Causes Likely Solutions
1. Suction Tube (20) detached.
2. Not enough liquid in tank.
3. Handle Assembly loose.
4. Hose Nut (22) loose.
5. Safety Cap (24) loose.
Unit does not spray
Spray pattern is undesirable
6. Sprayer not pressurized.
7. Spray fluid contains
particles or sand.
8. Nozzle and/or Filter clogged
with mineral buildup.
1. Nozzle needs adjustment.
2. Spray fluid contains
particles or sand.
3. Nozzle and/or Filter clogged
with mineral buildup.
2. AFTER EVERY USE, Clean the Sprayer:
a. Flush with water.
b. Clean Nozzle and Filter (21).
c. Rinse with water and allow to air-dry.
3. PERIODICALLY, lubricate all moving parts of
the pump assembly with petroleum jelly.
4. Store the Sprayer in a safe, dry, clean location
out of reach of children and out of sunlight.
1. Reattach Suction Tube.
2. Add liquid to tank.
3. Tighten Handle Assembly.
4. Tighten Hose Nut.
5. Tighten Safety Cap.
6. Pump Handle to pressurize Sprayer.
7. Disassemble, clean, then reassemble
Nozzle and/or Filter. Empty, clean, then
refill Tank with properly strained fluid.
8. Disassemble, clean, then reassemble
Nozzle and/or Filter.
1. Adjust Nozzle.
2. Disassemble, clean, then reassemble
Nozzle and/or Filter. Empty, clean, then
refill Tank with properly strained fluid.
3. Disassemble, clean, then reassemble
Nozzle and/or Filter.
Follow all safety precautions whenever diagnosing or servicing the Sprayer.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and
are not available individually as replacement parts.
Page 6 For technical questions, please call 1-800-444-3353. Item 61280/61281
Parts List and Diagram
5
6
7
8
9
10
11
12
13
14
17
18
19
20
21
22
23
24
25
26
27
28
29
15
16
34
30
33
31
36
32
35
37
1
2
3
4
Part Description Qty
1 Nozzle 1
2 O-Ring 1
3 Splitter 1
4 Bend 1
5 Wand 1
6 Wand Nut 1
7 Switch Body 1
8 Switch Body Nut 1
9 Sealing Washer 1
10 Valve Core 1
11 O-Ring 1
12 Spring 1
13 Trigger Handle Nut 1
14 Trigger 1
15 Washer 1
16 Trigger Handle 1
17 Hose 1
18 Valve 1
19 Washer 1
Part Description Qty
20 Suction Tube 1
21 Filter 1
22 Hose Nut 1
23 Funnel Top 1
24 Safety Cap 1
25 O-Ring 1
26 Pressure Release Valve 1
27 Spring 1
28 Tank 1
29 Bottom 1
30 Pump Nut 1
31 Direction Limiter 1
32 Piston 1
33 O-Ring 1
34 O-Ring 1
35 Air Tube 1
36 Plug 1
37 Handle 1
38 Shoulder Strap (not shown) 1
Page 7For technical questions, please call 1-800-444-3353.Item 61280/61281
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
™
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Loading...