Page 1
Page 2
SAFETY OPERATION MAINTENANCESETUP
.........................................................
....................................................
..............................................
follow this symbol to avoid possible injury or death.
will result in death or serious injury.
Addresses practices not related to personal injury.
SHO
TO
P
WARNING
– When using tools, basic precautions should always be followed, including the following:
Work Area
Distractions are
WARNING SYMBOLS AND DEFINITIONS
IMPORTANT SAFETY INSTRUCTIONS
Page 3
SAFETYOPERATIONMAINTENANCE SETUP
A
footing
Always wear eye protection.
ANSI-approved
Use the correct tool for the
Such preventive
A
Use of
When servicing a tool, use only identical
Air Source
Always
Such gases are capable of
SAVE THESE INSTRU
Page 4
SAFETY OPERATION MAINTENANCESETUP
ANSI
Vehicle must be safely supported by a
warnings, safety precautions, and instructions
Avoid burns. Allow the engine oil to completely
working pressure of 10
from service immediately and
SAVE THESE INSTRU
Symbols and Specific Safety Instructions
Page 5
Functional Description
Air Inlet
Valve
Valve
Air
SAFETYOPERATIONMAINTENANCE SETUP
Page 6
SAFETY OPERATION MAINTENANCESETUP
Y
INFORMATION
section at the beginning of this
For additional information regarding the parts listed in the following pages,
For additional information regarding the parts listed in the following pages,
This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up.
This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up.
Assembly
Assemble the Drain on flat, hard level surface.
fasten one Caster (20) to each bracket on the
Air Supply
FROM
in-line shutoff valve, and quick coupler for
A on page 7
An in-line shutoff
few drops of Pneumatic Tool Oil to the airline
few
Attach an air hose to the compressor's
Air flow, and therefore tool performance,
working.
Adjust the air compressor's output regulator
Adjust
Residual air pressure should not be present
Residual air pressure should not be present
Initial Tool Set Up/Assembly
Page 7
A:
H
F
C
A
Air Hose
Adjusts air pressure to tool
Air Cleaner / Dryer (optional)
Air Adjusting Valve (optional)
SAFETYOPERATIONMAINTENANCE SETUP
E
E
A
D
B
A
C
G
B
Lubricated
Tools
A
Non-lubricated
Tools
Page 8
SAFETY OPERATION MAINTENANCESETUP
Non-lubricated Tools
H
F
A
Anchor Bolts
Air Hose
Adjusts air pressure to tool
Air Cleaner / Dryer (optional)
Air Adjusting Valve (optional)
F
M
L O
L
Slope
H
K
J
C
Lubricated
Tools
G
E
D
J
N
I
I
C
F
C
B B
A A
Page 9
Operating Instructions
INFORMATION
section at the beginning of this
Workpiece and Work
Area Set Up
working.
Knob and lower Funnel to lowest position
below the oil
will indicate the reservoir fill level.
from one location to another. Only transport
Valve to horizontal position.
WARNING!
Do not leave Oil Lift
SAFETYOPERATIONMAINTENANCE SETUP
Page 10
SAFETY OPERATION MAINTENANCESETUP
P
FROM A
FROM TOOL FAILURE:
vibration,
These procedures are
These procedures are
the regular checks and maintenance
the regular checks and maintenance
P
wrap
P
After use, store in a dry, secure
Accumulated sludge.
After draining the oil, remove Plug and drain out sludge.
User-Maintenance Instructions
Page 11
AREFULL
Y
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
Parts List and Diagram
Acorn Nut
If product has no serial number,
If product has no serial number,
Some parts are listed and shown for
Some parts are listed and shown for
24
SAFETYOPERATIONMAINTENANCE SETUP
1
2
3
4
5
6
12
13
14
16
17
22
21
10
12
15
8
9
7
11
18
19
23
20
Page 12
Limited 90 Day Warranty
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
Loading...