Harbor Freight Tools 61204 Product manual

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 6

Setup .......................................................... 6

SAFETY OPERATION MAINTENANCESETUP

Operation .................................................... 7

Maintenance .............................................. 10

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.

3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.

7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.

8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.

Page 2 For technical questions, please call 1-888-866-5797. Item 61204

General Tool Safety Warnings (cont.)

Table A: RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.

10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

13. DON’T OVERREACH. Keep proper
footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.

17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of
rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Don’t
leave tool until it comes to a complete stop.

SAFETYOPERATIONMAINTENANCE SETUP

Page 3For technical questions, please call 1-888-866-5797.Item 61204

Grounding Instructions

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE
CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools with Three Prong Plugs

1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.

3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment­grounding conductor to a live terminal.

4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.

5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.

6. Repair or replace damaged or
worn cord immediately.

Grounding

Pin

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 V~ 3-Prong Plug and Outlet. The tool has a
grounding plug
that looks like the plug illustrated above
in 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.

9. Do not use an adapter to connect
this tool to a different outlet.

Cut-Off Saw Safety Warnings

1. For Your Own Safety Read Instruction

Manual Before Operating Grinder

2. Wear eye protection.

3. Use grinding wheel suitable for speed of grinder.

4. Replace cracked wheel immediately.

5. Always use guards and eye shields.

6. Do not overtighten wheel nut.

7. Use only flanges furnished with the grinder.

8. Frequently clean grinding dust from beneath grinder.

9. Wear a full face shield over ANSI­approved safety goggles during use.

Page 4 For technical questions, please call 1-888-866-5797. Item 61204

10. Do not grind with side of wheel unless wheel is
specifically designed for that type of grinding.

11. DO NOT OPERATE WITH ANY GUARD

DISABLED, DAMAGED, OR REMOVED. Moving
guards must move freely and close instantly.

12. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.

13. When servicing use only identical replacement parts.

14. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.

Cut-Off Saw Safety Warnings (cont.)

15. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.

16. Industrial applications must follow OSHA guidelines.

17. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

18. Avoid unintentional starting.
Prepare to begin work before turning on the tool.

19. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

20. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other
masonry products

• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

21. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

SAFETYOPERATIONMAINTENANCE SETUP

Vibration Safety

This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders. To
reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

22. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there
is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Page 5For technical questions, please call 1-888-866-5797.Item 61204

Specifications

Electrical Rating 120VAC / 60Hz / 5.5A

Motor No Load Speed 5000 RPM

SAFETY OPERATION MAINTENANCESETUP

Max. Accessory Diameter 6"

Arbor Size 7/8"

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and unplug the tool from its electrical outlet before
assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Functions

3150240

Moveable Guard

Angle Guide

Clamp

Handle

Trigger

Stationary

Guard

Blade

Base

Figure A

Page 6 For technical questions, please call 1-888-866-5797. Item 61204

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.

Tool Set Up

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the pressure and unplug the tool from its electrical outlet before
assembling or making any adjustments to the tool.

TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.

Installing the Wheel

1. The Grinding Wheel MUST be:

• rated to at least 5000 RPM.

• no larger than 6" in diameter.

• fitted with a 7/8" round arbor hole.

• suitable for edge grinding, not surface grinding.

• dry and clean.

• proven undamaged by inspection and
by the ring-test explained below.

2. Closely inspect the Grinding Wheel before mounting.
Perform a ring-test on the wheel

(unlesswheelissmallerthan4″)asfollows:

a. Suspend wheel using a dowel or

finger through the arbor hole.

45° 45°

Hang

Wheel

from

Dowel

V
E
R
T

I
C
A
L

3. Release the Safety Chain and guide the
Housing to rest at its full upward position.

Moveable Guard

Swing open

Loosen the Knob on the Moveable Guard and

4.
swing it open, exposing the Blade and Flange.

5. Using the included wrenches, hold the Spindle
in place with the flat Wrench and loosen
the Outer Flange with the Pin Wrench.

SAFETYOPERATIONMAINTENANCE SETUP

Nut

Figure B

Tap

Wheel

Here

C
E
N
T
E
R

45° 45°

b.

Tap the flat side of the wheel with a light non­metallic object, such as a screwdriver handle,
at a point 45° from the vertical center line on
each side of the wheel and 1 – 2 inches from
the edge of the wheel (see Illustration).

c. Rotate the wheel 90° and repeat the test

until the entire wheel has been checked.

d. An undamaged wheel will

give a clear tone. If cracked, there will be
a dead sound and not a clear ring.

6. Remove the Outer Flange and Blade,
noting the orientation of each.

7. For wheels with paper gaskets (blotters) or
metal gaskets: Slip the grinding wheel onto the
Spindle with the gasket first. The gasket should be
centered on the grinding wheel and the wheel and
gasket should rest flat against the Inner Flange.

WARNING: To prevent serious
injury, gaskets must be used for all
grinding wheels they are provided with.
Gaskets help prevent grinding wheel damage
and wheel slippage, causes of wheel failure.

8. Thread the Outer Flange onto the Spindle
and tighten in place with the Wrenches.

9. Swing the Moveable Guard back in
place and tighten the Knob.

10. Lower the Housing and replace the Safety Chain.

Page 7For technical questions, please call 1-888-866-5797.Item 61204

Angle Guide

Clamp Knob

Flip open

SAFETY OPERATION MAINTENANCESETUP

Quick Release

Figure C

The Clamp and Angle Guide are used together to hold the workpiece securely in place.
The Angle Guide can be adjusted from 0 to 45° for straight or angled cuts. Adjust the
Angle Guide first, then secure the workpiece in place with the Clamp.

Bolt

Two Locations

1. To adjust the Angle Guide:

a. Loosen both Bolts.

b. Turn the Angle Guide to the desired angle.

c. Retighten the bolts.

Note: The Angle Guide can be positioned
in either pair of holes in the Base.

2. To secure a workpiece in the Clamp:

a. Turn the Handle counterclockwise a quarter turn.

b. Flip up the Quick Release.

c. Slide the clamp out as far as needed.

d. Position the work piece against the angle Guide.

e. Flip the Quick Release down

onto the Clamp threads.

f. Push the Clamp against the workpiece.

g. Tighten the Handle clockwise

to secure the workpiece.

Page 8 For technical questions, please call 1-888-866-5797. Item 61204

Work Piece and Work Area Set Up

1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.

General Operating Instructions

CAUTION! Friction from cutting will heat both the

Wheel and the workpiece. Be careful when handling
the workpiece and do not overwork the Cut-Off Saw as
the Wheel can become damaged from overheating.

1. Release the Safety Chain and guide the
Housing to rest at ifs full upward position.

2. Adjust the Angle Guide as needed.

3. Place the workpiece against the Angle
Guide and the Clamp in place.

4. Plug the Power Cord into a 120V~
grounded, electrical outlet.

2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.

3. Secure loose work pieces using the clamp
to prevent movement while working.

SAFETYOPERATIONMAINTENANCE SETUP

6. With one hand on the Handle and the other hand
clear, slowly bring the Saw down, letting the Saw
do the work. Do not apply excessive force.

7. After making the cut, release the
Power Switch and raise the Saw.

8. Wait until the unit comes to a complete
stop then remove the workpiece.

9. To prevent accidents, turn off the tool and
disconnect its power supply after use. Lower the
Housing and secure with the Safety Chain. Clean,
then store the tool indoors out of children’s reach.

5. Squeeze and hold the Trigger to start the Saw.

Page 9For technical questions, please call 1-888-866-5797.Item 61204

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and unplug the tool from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

3. WARNING! If the supply cord of this

Cut-off Wheel Storage and Handling

1. Handle Cut-off Wheels carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.

2. Store Cut-off Wheels in shelves, racks, boxes, or

of the tool with clean cloth.

power tool is damaged, it must be replaced
only by a qualified service technician.

drawers. Storage area must be kept dry, and above
freezing. Any grinding or cut-off wheels exposed to
humidity or freezing temperatures must not be used.

Page 10 For technical questions, please call 1-888-866-5797. Item 61204

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Internal damage or wear. (Carbon
Brushes or switch, for example.)

Tool operates
slowly.

Performance
decreases
over time.

Excessive noise
or rattling.

Overheating. 1. Forcing machine to work too fast.

Extension cord too long or
wire size too small.

1. Accessory dull or damaged.

2. Carbon brushes worn or damaged.

Internal damage or wear. (Carbon
Brushes or bearings, for example.)

2. Accessory misaligned.

3. Accessory dull or damaged.

4. Blocked motor housing vents.

5. Motor being strained by long or
small diameter extension cord.

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.

3. Check and replace Carbon Brushes
or have technician service tool.

Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.

1. Keep cutting accessories sharp.
Replace as needed.

2. Replace brushes.

Check and replace Carbon Brushes
or have technician service tool.

1. Allow machine to work at its own rate.

2. Check and correct accessory to
fence and/or table alignment.

3. Keep cutting accessories sharp.
Replace as needed.

4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.

5. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Table A on page 3.

SAFETYOPERATIONMAINTENANCE SETUP

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

Page 11For technical questions, please call 1-888-866-5797.Item 61204

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

SAFETY OPERATION MAINTENANCESETUP

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 12 For technical questions, please call 1-888-866-5797. Item 61204

SAFETYOPERATIONMAINTENANCE SETUP

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 13For technical questions, please call 1-888-866-5797.Item 61204

Parts List and Diagram

Parts List

SAFETY OPERATION MAINTENANCESETUP

Part Description Qty

1 Knob 1
2 Mechanical Spring 1
3 Moveable Guard 1
4 Outer Flange Nut 1
5 Inner Flange 1
6 Ø5x12 S/T Screw 3
7 Ø5 Spring Washer 3
8 Grinder Cover 1
9 Output Shaft 1

10 2.9X10 Semicircle Key 1

11 4X55 Self-Tapping Screw 4
12 Bearing Seat 1
13 201# Bearing 1
14 201# Triangle Press Cover 1
15 Ø4 Spring Washer 3
16 Ø4x10 S/T Screw 3
17 Gear 1
18 Ø10 Retaining Ring 1
19 17# Bearing 1
20 Right Motor Housing 1
21 Ø4x20 S/T Screw 5
22 Ø4x12 S/T Screw 2
23 Trigger 1
24 Left Motor Housing 1
25 19# Bearing 1
26 Rotor 1
27 Brush Holder 2
28 Brush 2
29 Cap 2
30 18# Bearing 1
31 Stator 1
32 100# Pull Spring 2

Part Description Qty

33 5X14 Hexagonal Screw 2
34 Ø5 Spring Washer 2
35 Terminal 2
36 Pin 1
37 Spring 1
38 Support/Base Plate 1
39 Machine Foot 3
40 Gasket 3
41 M4 Nut 3
42 Ø4x30 S/T Screw 3
43 Chain 1
44 Screw Pole 1
45 2X20 Cotter Pin 1
46 4X24 Spring Pin 1
47 Nut Holder 1
48 Quick Release Nut 1
49 Ø6x16 S/T Screw 2
50 Ø6 Spring Washer 2
51 Ø6 Washer 2
52 Straight Pin 1
53 Small Clamp Plate 1
54 Large Clamp Plate 1
55 6X14 Hexagon Screw 2
56 Ø6 Spring Washer 2
57 Ø6 Washer 2
58 Cable Guard 1
59 Power Cord 1
60 Cable Press Plate 1
61 Ø4x14 S/T Screw 2
62 Ø 7/8"Flange 1
63 Pin Wrench 1
64 Flat Spanner 1

Page 14 For technical questions, please call 1-888-866-5797. Item 61204

Assembly Diagram

SAFETYOPERATIONMAINTENANCE SETUP

Page 15For technical questions, please call 1-888-866-5797.Item 61204

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797