Harbor Freight Tools 60730 Owner's Manual
Specifications
Capacity 500 lb.
Table Height 9" – 28-1/2"
Table Size 27-3/8" x 17-3/4"
Unpacking Precautions
Note: When unpacking, use assistance when lifting the Hydraulic Lift Table from the box.
Or set the packaging box sideways and slide the Lift Table out from the box sideways.
CAUTION! When lifting Hydraulic Lift Table from packaging box, be sure to grip the main frame.
Do not just grip the Table. Doing so will only raise up the Table and keep the unit’s frame in the packaging box.
Important Safety Information
1. Do not exceed 500 lb. max weight capacity.
Be aware of dynamic loading!
Sudden load movement may briefly create
excess load causing product failure.
2. Use only on flat, level and hard surface capable of
supporting the Lift Table and any item(s) placed on
Table. Evenly distribute load on Table to avoid tipping.
3. Use as intended only. Do not use Lift Table to
lift or transport animals, pets, or people.
4. Assemble only according to these instructions.
Improper assembly can create hazards.
5. Follow all hydraulic bleeding instructions
specified in this manual.
6. Wear ANSI-approved safety goggles and heavy-duty
work gloves during assembly and use.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under
the influence of drugs or medication.
10. This product is not a toy. Do not allow
children to play with or near this item.
11. Use as intended only.
12. Inspect before every use; do not use
if parts are loose or damaged.
13. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Page 2 For technical questions, please call 1-800-444-3353. Item 60730
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
document including all text under subheadings therein before set up or use of this product.
The Hydraulic Lift Table requires some
assembly after you unpack it.
Front
Wheels
(47)
Lock Nuts (14)
Washer (15)
Bushing (48)
Hex Bolts (16)
Figure 1
First, set aside the hardware needed to
1.
install the Front Wheels (47). The hardware
includes the Hex Bolts (16), Lock Nuts (14),
Washers (15), and Bushings (48).
Lifting Pedal
Connector
(30a)
Wrench
Lifting
Pedal
(27)
Bolt (29)
Figure 3
Slide Lifting Pedal (27) into Pedal
3.
Connector (30a), aligning the installation holes.
Then slide the Bolt (29) through the Washer (15)
and through the installation holes. Use the
wrench to fasten the Lock Nut (12) over the Bolt,
securing Lifting Pedal in place. See Figure 3.
Handle
(21)
Wrench
Washer (15)
Wheel
Frame
Front Wheel
(47)
Lock Nut (14)
Figure 2
2. Turn Lift Table on its side. Slide Bushing through
center hole in the Front Wheel. Then set Front Wheel
in the wheel frame of the Base Assembly (17).
Slide the Hex Bolt through the Washer, wheel
frame and Bushing. Use a wrench (sold separately)
to fasten Lock Nut onto Hex Bolts, until the
Front Wheel is secured into place.
Wrench
Bolt (20)
Figure 4
Slide the ends of the Handle (21) into the
4.
Base
Assembly
(17)
handle slots on the Base Assembly (17).
Use the wrench to tighten the Bolts (20) until Handle
is securely fastened in place. See Figure 4.
5. WARNING! After assembly, try out the
Lift Table to make sure it is functioning
properly before using it to lift a load.
Page 3For technical questions, please call 1-800-444-3353.Item 60730
Loading...