Harbor Freight Tools 60727 Product manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

10 ft. x 17 ft.

Portable Garage

Patent No.: US20120234418 A1; D409310; 7296584

Visit our website at: http://www.harborfreight.com

Email our technical support at: tech@harborfreight.com

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

ITEM 60727

Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

Table of Contents

Safety ......................................................... 3

Specifications ............................................. 4

Assembly .................................................... 4

Maintenance .............................................. 10

Parts List.................................................... 11

Warranty .................................................... 12

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

Addresses practices not related to personal injury.

WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.

Read the manual before assembly and/or use.

will result in death or serious injury.

could result in death or serious injury.

could result in minor or moderate injury.

WARNING marking concerning Risk of Head Injury. Wear hard hat during assembly and service.

WARNING marking concerning Risk of Hand Injury. Wear heavy-duty work gloves during assembly and service.

Page 2 For technical questions, please call 1-800-444-3353. Item 60727

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in serious injury.

Save all warnings and instructions for future reference. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

Assembly Precautions

1. Do not assemble in windy conditions.

2. Assemble and install only on

flat, level, hard surface.

3. Assemble and anchor only according to

these instructions. Improper assembly or inadequate anchoring can create hazards.

4. Check for utility lines, tree branches and other structures before assembling.

5. Verify that installation surface has no hidden utility lines before anchoring.

Use Precautions

1. DO NOT USE IN HIGH WIND. Remove cover if harsh weather or heavy rain threatens.

2. For temporary use only. Do not use for long-term shelter.

3. Do not use as tent. Does not meet tent flammability standards. Do not use grill, heater, or ignition sources inside or near cover.

SAFETYMAINTENANCE ASSEMBLY

6. Wear ANSI-approved safety goggles, heavy-duty work gloves and hard hat during assembly and service.

7. Keep assembly area clean and well lit.

8. Keep bystanders out of the area during assembly.

9. Do not assemble when tired or when under the influence of drugs or medication.

10. Product capabilities apply to properly and completely assembled product only.

7. Use as intended only.

8. Inspect regularly, tighten all loose hardware and loose ropes, and secure all loosened anchors. If any parts are damaged, bent, or stretched, they must be replaced. Hardware may loosen during normal operation stresses. Loose hardware or damaged/altered parts will compromise the structural integrity of this product.

4. Do not allow snow, rainwater or debris

to accumulate or pool on cover.

5. Do not hang objects from any part of the Garage.

6. This product is not a toy. Do not allow children to play with or near this item.

SAVE THESE INSTRUCTIONS.

9. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-800-444-3353.Item 60727

Specifications

Overall Dimensions 10′ W x 17′ L Center Height 8′

Side Height 6′ 3″ Pole Diameter 1.34″

Assembly Instructions

SAFETY

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY: Do not leave this product partially assembled. Assemble this product completely at one time.

Note: At least 3 workers are required for assembly. Before starting assembly, review the instructions and make sure

there is enough time and the proper tools available to properly assemble. Finger tighten all connections until assembly is done. Assemble on a flat, level surface.

Frame Assembly

1. Construct two End Assemblies using 3-Way Connectors (11), Rafters (3), Roof Corners (10), Stabilizers (16), Corner Legs (2), Corner Feet (9), Bolts (17, 18, 19) and Nuts (20).

ASSEMBLY

MAINTENANCE

2017

Figure A: End Assembly

Page 4 For technical questions, please call 1-800-444-3353. Item 60727

+ 8 hidden pages