Harbor Freight Tools 60726 Product manual

Specifications

Length

Min Max

2-Ton Hydraulic Push Ram (with Saddle) 53⁄8″ 83⁄8″ 5700 PSI 4400 lb. 15⁄8″

4-Ton Hydraulic Push Ram 111⁄16″ 23⁄8″ 5700 PSI 8800 lb. 2″

4-Ton Hydraulic Push Ram (with Spring) 101⁄2″ 153⁄8″ 8000 PSI 8800 lb. 15⁄8″

10-Ton Hydraulic Push Ram (w/Saddle & Spring) 5″ 71⁄2″ 8800 PSI 22000 lb. 23⁄16″

10-Ton Hydraulic Push Ram (with Spring) 14″ 195⁄8″ 8800 PSI 22000 lb. 21⁄8″

2-Ton Hydraulic Pull Ram (with Spring) 91⁄2″ 141⁄2″ 7800 PSI 4400 lb. 11⁄2″

5-Ton Hydraulic Pull Ram (with Spring) 113⁄4″ 173⁄4″ 8800 PSI 11000 lb. 23⁄8″

Note: This equipment requires a compatible Hydraulic Pump, hydraulic hoses,
and hydraulic fittings to operate properly. None of this equipment is provided,
and all of it must be properly rated for use with this kit.

Operating

Pressure

Capacity Diameter

Page 2 For technical questions, please call 1-800-444-3353. Item 60726

Important Safety Information

1. Do not exceed operating pressure
or maximum length for any ram,
refer to Specifications chart.

2. Use as intended only. Do not use
this item to raise or move a vehicle.

3. Use according to vehicle’s
service instructions only.

It is beyond the scope of this manual to
discuss body/frame repair guidelines.
It is the responsibility of the user to
consult a body/frame repair technical
manual for full instructions.

4. Wear ANSI-approved safety goggles
and heavy-duty work gloves
during setup and use.

5. Stay clear of Rams during operation.
Position body as far away as
practical when Ram is under load.
Ram can slip suddenly, causing injury.

6. Keep work area clean and well lit.

7. Keep bystanders out of the work area.

8. Do not use when tired or when
under the influence of alcohol,
drugs or medication.

9. This product is not a toy. Do not allow
children to play with or near this item.

10. Inspect before every use; do not use
if parts are loose or damaged.

11. Maintain product labels and nameplates.
These carry important
safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

12. Use compressed hydraulic fluid only.
Do not use any other power source
or fluid to operate this product.

13. Read and understand Hydraulic Pump
instructions before use.

14. Before working on a vehicle, set the
parking brake and block the tires.

15. Avoid off-center loads.
If the Hydraulic Pump (not included)
unit seems unusually hard to pump,
immediately stop the operation.
Adjust the Hydraulic Ram unit to
eliminate or diminish an off-center load.

16. The results you achieve with these
tools will depend upon your skill and
experience at using tools of this type.

Harbor Freight Tools is not
responsible for damage to vehicles
caused by misuse of these tools.

17. Keep the Hose Couplers protected
when the Hydraulic Rams are not
in use. Screw Dust Caps into all
Hose Couplers when not in use to keep
Ram internal mechanisms clean.

18. The warnings and cautions discussed
in this manual cannot cover all
possible conditions and situations
that may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
be built into this product, but must
be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-800-444-3353.Item 60726

Product Components

2-Ton Push Ram

with Saddle (A)

4-Ton

Push

Ram (B)

5-Ton
Hook

10-Ton Push Ram

with Saddle & Spring (D)

5-Ton Pull Ram
with Spring (G)

2-Ton

Hook

10-Ton Push Ram

with Spring (E)

2-Ton Pull Ram

with Spring (F)

4-Ton Push Ram

with Spring (C)

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.

Refer to instructions provided with pump, hoses, and fittings for proper
hydraulic line purging, preparation, and connection procedures.

Page 4 For technical questions, please call 1-800-444-3353. Item 60726