Harbor Freight Tools 44859 User Manual

8” X 12” LATHE

44859

ASSEMBLY AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised 09g

Specifications

ITEM DESCRIPTION

Power 110VAC, 60 Hz, 550 watts

Motor 3/4 HP

Distance between Centers 12 inches

Swing over Bed 8 inches

Spindle Step Speeds 125, 210, 420, 620, 1000, 2000 RPM

Spindle Bore 3/4 inch

Spindle Taper MT3

Tailstock Taper MT2

Chuck Capacity 4 inch, 3-jaw; reversing jaws

Cross Slide Travel 4-1/2 inches

Tool Slide Travel 2-3/4 inches

Slide Scale 0.001 inch per mark tool

Metric Thread Pitches 10 (0.4 ~ 3.0 mm)

SAE Thread Pitches 12 (8 ~ 40 TPI)

Accessories - 3 reverse jaws for chuck

- Chuck wrench

- Dead centers MT2 and MT3

- Wrenches: 10-12 open end, 14-17 open end
17-19 open end, 45-52 round nut, tool post

- Hex wrenches: 3, 4, 5, 6mm

- 2 Drive Belts

- Threading gear set

Weight 254 lb.

NOTE: The Splash Guard shown in the cover page photo is not included. It can be
ordered from Harbor Freight Tools using SKU 26962.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.

07h, 07l

SKU 44859

Page 2

3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force tool. It will do the job better and more safely at the rate for which it was
intended. Do not use inappropriate attachments in an attempt to exceed the tool
capacity.

6. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are certain applications for which this tool
was designed. Do not modify this tool and do not use this tool for a purpose for which
it was not intended.

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.

9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.

10. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and, if damaged, have them repaired by an authorized technician.
The handles must be kept clean, dry, and free from oil and grease at all times.

11. Disconnect power. Unplug tool when not in use.

12. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before plugging it in.

13. Avoid unintentional starting. Be sure the switch is in the Off position when not in
use and before plugging in.

14. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.

15. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified technician.
Do not use the tool if any switch does not turn On and Off properly.

16. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.

17. Replacement parts and accessories. When servicing, use only identical

SKU 44859

Page 3

replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.

18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.

19. Use proper size and type extension cord. If an extension cord is required, it must be
of the proper size and type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or cause electrical damage
to the tool. This tool requires use of an extension cord of 0 to 12 amps capability (up
to 50 feet), with wire size rated at 16 AWG. Longer extension cords require larger size
wire. If you are using the tool outdoors, use an extension cord rated for outdoor use
(signified by “WA” on the jacket).

21. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.

22. Know your power tool. Read and understand this assembly and operating manual,
and labels affixed to the tool. Learn it’s application and limitations, as well as the
specific potential hazards particular to this tool.

23. Ground the tool. This tool is equipped with an approved 3-conductor cord and 3­prong grounding type plug to fit a grounding type receptacle. The green wire in the
cord is the grounding wire. Never connect the green wire to a live terminal.

24. Use safety guards. Keep guards in place, in working order, and in proper adjustment
and alignment.

25. Secure workpiece. Use clamps or a vise to hold workpiece when practical. Keep both
hands free to operate tool.

26. Direction of Feed. Feed workpiece into the blade or cutter against the direction of the
rotation.

Note: Performance of this tool may vary depending on variations in local line voltage. Exten­sion cord usage may also affect tool performance.

Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under­stood by the operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure that all the parts are included. Refer to the Accesso­ries list in the Specifications table, and the Parts List.

If any parts are missing or broken, please call Harbor Freight Tools at the number on the
cover of this manual as soon as possible.

07h

SKU 44859

Page 4

Installation

1. Carefully place the Lathe on a sturdy, level work table with sufficient light.

2. Use appropriate hardware (not included) in the mounting holes of the lathe base, to
properly secure the lathe. The work table must also be properly mounted to the floor.

3. Before operation, verify that the slide, worktable, and spindle can move, and are not
locked in place.

4. Clean machine with nonflammable solvent and oil the machine according to the
lubrication requirements (see Lubrication section) before running the machine.

Operation

This 8 x 12 inch Lathe is capable of machining metal and nonmetallic stock by cutting,
drilling, and milling. It can cut circular surfaces, both inside and out, cones, mill planes or
grooves, and other cutting functions depending on the tools used. It can also create SAE
and metric threads.

Controls

B

A

E

F

H

I

D

NOTE: The Splash Guard shown in the photo above is not included. It can be ordered using SKU 26962.

ITEM NAME USAGE ASSY NO.

A Reversing Switch Change rotation direction of the spindle 200

B Master Switch Turn machine power On and Off 200

C Turn Lever Moves saddle transversely 500

D Turn Lever Moves saddle longitudinally 600

E Straight Lever Clamps the square tool rest 400

F Straight Lever Moves the square tool rest carriage longitudinally 400

G Straight Lever Controls apron clasp nut 600

H Straight Lever Controls tailstock sleeve 300

I Turn Lever Moves tailstock sleeve longitudinally 300

SKU 44859

C

G

Page 5

07h

Lathe Safety Precautions

1. Keep fingers away from revolving parts and cutting tools while in operation.

2. Never force cutting action.

3. Never perform an abnormal or little used operation without study and use of adequate
blocks, jigs, stops, and fixtures.

4. Verify proper cutting speed for the material being cut, and any special operation, in a
machinery shop handbook.

5. Do not open drive cover while in operation.

6. Always remove chuck key from chuck.

7. Do not attempt to adjust or remove tools when lathe is in operation.

8. Always keep cutting tools sharp.

Cutting Procedures

The instructions that follow are basic operational procedures. It is assumed that the opera­tor understands lathe operation and it’s capabilities.

1. Rotate Turn Lever (C) counterclockwise to move the saddle outward.

2. Place the workpiece in the chuck, center, and secure with the chuck key.

3. Loosen the Straight Lever (H) and then rotate the Turn Lever (I) clockwise to engage
the Dead Center tool into the end of the workpiece. Tighten Straight Lever (H) again.

4. Select the desired tool set and place it into the tool rest. Align the tool nose to the
spindle centerline, then tighten.

5. Open the Gear Box and verify that the proper
speed is engaged.

Typically, the harder the metal workpiece, the

faster the spindle speed.

6. Set the desired feed amount according to the
type of stock, workpiece dimensions, and the
type of cut.

7. Close the Gear Box.

8. Open the safety cover over the On / Off switch and press the green On button.

Verify that the lathe head and feed amount is correct.

9. Align the tool nose on the workpiece where the cut is to begin.

10. Rotate the Turn Lever (C) clockwise to move the saddle transversely, moving the tool
nose into the workpiece for cutting.

11. When the cut is complete, press the red Off button.

SKU 44859

Page 6

Machining Cylinders

1. Repeat the cutting procedure steps 1 through 8, listed on the previous page.

2. Rotate Turn Lever (D) clockwise and move the saddle to the right of the workpiece.

3. Rotate Turn Lever (C) clockwise until the desired depth of cut is reached on the far
right surface of the work piece.

4. Press down on the Straight Lever (G) to engage apron clasp nut over the Gear Shaft.

The tool will automatically move from right to left while cutting the workpiece.

5. When the cut is complete, press the red Off button.

Optionally, you can turn the Reverse switch to have the tool go over the same cut in

the opposite direction (left-to-right). This will clean and smooth the previous cut.

6. When the cut is complete, press the red Off button.

Machining Cones

Manually

This operation is similar to machining cylinders with the following differences.

1. To manually cut a cone, determine the taper requirement and turn the small cutter rest
to the desired slope on the workpiece. Retighten the cutter rest.

2. Press the green On button to start the lathe.

3. Turn the Straight Lever (F) clockwise to make the cut.

Automatically

1. To automatically cut a cone, determine the taper requirement and turn the small cutter
rest to the desired slope on the workpiece. Retighten the cutter rest.

2. Horizontally move the tailstock from the spindle centerline to the required slope on the
far right surface of the work piece.

3. Press the green On button to start the lathe.

4. Press down on the Straight Lever (G) to engage apron clasp nut over the Gear Shaft.

The tool will automatically move from right to left while cutting the workpiece.

5. Repeat steps 2 through 4 until the desired cone size is cut.

6. When the cut is complete, press the red Off button.

Machining Threads

The Gear Box is composed of the change gears, shaft bolt, fixing shaft bolt, and square
nut. The change gear box is fixed on the left support of the leadscrew (101). To cut threads,
select the proper change gears for the desired thread type (see Thread Formula Table), and
engage with approximately 0.1 mm tolerance. Tighten Screw (835).

SKU 44859

Page 7

The Fixed Shaft Bolt (825) under the spindle is used for right hand cutting and threading.
The set of Fixed Shaft Bolts in the accessory kit is used in combination with the original set
of Shaft Bolts to reverse the rotation of the long leadscrew for left-handed threading and
cutting.

The change gear for metric or inch threading is selected according to the Thread to Gear
formula and table. The feed amount depends on the material to be cut, the surface rough­ness, and finish requirements. If the two settings “0.1 and 0.2”, of the Gear table do not
meet the requirement, you can add or change gears. The same is true if the number of
teeth listed in the Gear table do not coincide with the calculated number of teeth. In this
case, use gears with similar number of teeth. In doing so, however, the following relation­ship of the driving shaft must be met: Z3+Z4+>Z2+Z5. Otherwise, the addendum of circles A2
and Z5 will hit each other.

The left formula below is an example of 0.3 mm spindle round. The right formula is an ex­ample for 8 threads per inch.

The Thread to Gear settings table on the following page allows you to select the number of
threads per inch or millimeter, and which gears need to be used.

SKU 44859

Page 8

Rest Accessories

The Follow Rest (not supplied) is mainly used for cutting long and thin shaft pieces to en­sure no bending takes place during cutting. It also provides a better finish surface as a
result of less vibration. The Steady Rest (not supplied) provides a similar function as with
the Follow Rest. The difference being that the Steady Rest is fixed on the bed guides, and
does not follow the movement of the cutting tool. Both rests can be purchased from Harbor
Freight Tools.

Maintenance

General

1. Unplug power cord from receptacle when not in use.

2. Using compressed air, blow off all dirt and particles after using.

3. Keep all tools sharp.

4. Cover Lathe when not in use.

5. Periodically, check all bolts and nuts for tightness.

Lubrication

Lubricate the Lathe daily using an appropriate machine oil from a forced-feed oil can.

SKU 44859

Page 9

ITEM PART TO BE LUBRICATED LUBE POINT

See lubrication location illustration on next page

1 Fix bolt of intermediate gear Oil Cup

2 Leadscrew support Oil Cup

3 Cutter rest screw Oil Cup

4 Cutter rest carriage Oil Cup

5 Tailstock sleeve Oil Cup

6 Tailstock leadscrew Oil Cup

7 Leadscrew support Oil Cup

8 Sync. counter-pulley over shaft Oil Cup

9 Change gear, shaft bolt Oil Cup

10 Change gear Oil Cup

11 Bed guides Oil Cup

12 Saddle Carriage Oil Cup

13 Saddle leadscrew Oil Cup

14 Saddle Carriage Oil Cup

15 Bed guides Oil Cup

16 Cutter rest leadscrew Oil Cup

17 Apron Oil Cup

18 Bed guides Oil Cup

19 Saddle carriage leadscrew support Oil Cup

20 Apron Oil Cup

21 Bed guides Oil Cup

22 Leadscrew On Leadscrew

Lubrication Points

SKU 44859

Page 10

SKU 44859

Page 11

Headstock Parts List

ITEM # NAME QTY REMARKS

201 Front Oil Ring 1

202 Roller Bearing 2 35x62x17

203 Oil Ring 1

204 Screw 4 M3x8

205 Front Panel 1

206 Rear Oil Ring 1

207 Tube Separator 1

208 Spindle Pulley 1

209 Nut 2 M27x1.5

210 Spindle Gear 1

211 Screw 4 M5x10

212 Switch Box 1

213 Headstock 1

214 Plat Key 1 4x40

215 Screw 3 M8x16

216 Spindle 1

217 Cover 1

NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU­TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 44859

Page 12

Headstock Assembly Drawing

SKU 44859

Page 13

Motor and Pulley Drive Parts List

Motor and Pulley Drive Parts List

ITEM # NAME QTY REMARKS

1501 Nut 3 M5

1502 Synchronized Counter

Pulley

1503 Slide Bearing 1

1504 Shaft 1

1505 Over Plate 1

1506 Washer 1 12

1507 Washer 1 10

1508 Nut 1 M12

1509 Nut 1 M10

1510 Nut 1 M12

1511 Screw 4 M5x8

1512 Motor Guard Assem-

bly

1513 Bolt 3 M10x20

1514 Washer 1

1515 Washer 1

1516 Fan-Support 1

1517 Protecting Cover Rest 1

1518 Washer 1 8

1519 Screw 2 M5x12

1520 Synchronized Tooth

Belt

1521 V-Belt 1 0-710

1522 Pivot 1

1523 Bolt 1 M8x20

1524 Bearing Arbor 1

1525 Tension Pulley 1

1526 Single Row Annular

Bearing

1527 Check Ring 1 12

1528 Tube Separator 1

1529 Front Feed Oil Cup 1 6

1530 Check Ring 1 12

1531 Big Washer 1

1532 Check Ring 1 12

1533 Check Ring 1 28

1534 Front Panel 1

1535 Cover 1

1536 Screw 1 M5x35

1

1

1 M1.5xZ118

2 12x28x8

1537 Check Ring 1

1538 Motor Pulley 1

1539 Screw 5 M5x8

1540 Check Ring 1

1541 Synchronized Drive

Pulley

1542 Hinge 2 75(3”)

1543 Check Ring 1

1544 Motor 1 550W

1545 Washer 4 8

1546 Bolt 4 M8x25

1

SKU 44859

REV 09g

Page 14

Motor and Pulley Drive Assembly Drawing

SKU 44859

Page 15

Bed Parts List

ITEM # NAME QTY REMARKS

101 Left Support of Lead Screw 1

102 Flat Key 1 4 x 6

107 Bed 1 A 400B 555

108 Screw 1 M8 x 12

109 Screw A 4 B 5 M5 x 16

110 Oil Cup 2

111 Right Support of Lead Screw 1

112 Screw 1 M6 x 16

113 Laer-pin 1 6 x 22

114 Lead Screw 1

115 Rack 1

116 Screw 3 M4 x 16

117 Adjusting Disc 1

118 Spring Pin 2 5 x 16

SKU 44859

Page 16

Bed Assembly Drawing

SKU 44859

Page 17

Tailstock Parts List

ITEM # NAME QTY REMARKS

301 Screw 1 M8x20

303 Washer 1 B12

304 Nut 1 M12

305 Tailstock Body 1

306 Single Row Radial Ball Bearing 1 8101

307 Tailstock Leadscrew 1

308 Tailstock Sleeve 1

310 Washer 1 B8

311 Bolt 1

312 Hand Lever 1

313 Force Feed Oil Cup 2 6

314 T-type Flat Key 1

315 Screw 1 M8x16

316 Screw 4 M5x16

317 Tailstock End Cover 1

318 Cylinder Pin 1 4x30

319 Spring Bow 1

320 Handwheel 1

321 Hand Lever Bolt 1

322 Hand Lever Sleeve 1

323 Index Ring 1

324 Bolt 1 M12x80

325 Tailstock Clamp Plate 1

326 Base 1

SKU 44859

Page 18

Tailstock Assembly Drawing

SKU 44859

Page 19

Rest Parts List

ITEM # NAME QTY REMARKS

401 Nut 2

402 Index Piece 1

403 Rivet 2

404 Cutter Rest Revolving Disc 1

405 Rest Bolt 1

406 Nut 3 M4

407 Screw 3 M4x20

408 Screw 1 M4x12

409 Nut 1 M4

410 Position Pin 1

411 Square Cutter Rest 1

412 Screw 8 M8x25

413 Hand Lever 1

414 Hand Lever Base 1

415 Washer 1

416 Spring 1

417 Cutter Rest Carriage 1

418 Pad Iron 1

419 Cylinder Pin 1 3x10

420 Cutter Rest Carriage Lead 1

421 Flat Key 1 3x10

422 Force Feed Oil Cup 2 6

423 Leadscrew Support 1

424 Screw 2 M5x16

425 Spring Bow 1

426 Hand Lever 2

427 Nut 1 M8

428 Washer 1 B8

429 Cutter Rest Carriage Hand Wheel 1

430 Index Ring 1

431 Screw 2 M6x22

432 Clamp Disc 1

SKU 44859

Page 20

Rest Assembly Drawing

SKU 44859

Page 21

Saddle Parts List

ITEM # NAME QTY REMARKS

501 Screw 1 M5x10

502 Washer 1

503 Oil Cup 9

504 Nut 1

505 Middle Saddle 1

506 Large Saddle 1

507 Screw 4 M5x20

508 Screw 1 M8x20

509 Screw 4 M6x35

510 Protecting panel and oil-stopping falt 1

511 Screw 2 M8x10

512 Protecting panel and oil-stopping falt 1

513 Screw 4 M525

514 Nut 4 M5

515 Pad Iron 1

516 Protecting panel and oil-stopping falt 1

517 Screw 8 M3x12

518 Rear-clamp plate 1

519 Pad Iron 1

520 Screw 4 M5x16

521 Nut 5 M4x16

522 Screw 5 M4x16

523 Protecting panel and oil-stopping falt 1

524 Flat Key 1 4x8

525 Screw 3 M5x22

526 Pring Bow 1

527 Washer 1

528 Screw 1 M6x10

529 Bracking Plate 1

530 Saddle Front-clamp Plate 1

531 Hand Lever Bolt 1

532 Hand Lever Sleeve 1

533 Hand wheel 1

534 Rolling Bearing 1 8101

535 Index Ring 1 100 Rulled

536 Bearing Base 1 0.02mm

537 Rolling Bearing 1 8101

538 Leadscrew 1 10TPI

539 Leadscrew support 1

540 Nut 1 10TPI

541 Screw 2 M3x16

542 Screw 2 M8x20

SKU 44859

Page 22

Saddle Assembly Drawing

SKU 44859

Page 23

Apron Parts List

ITEM # NAME QTY REMARKS

601 Slotted Disc 1

602 Taper Pin 1 3x20

603 Shaft Sleeve 1

604 Case 1

605 Bolt 3 M5x30

606 Nut 3 M5

607 Revolving Shaft 1

608 Hand Lever 1 Shared Piece

609 Steel Ball 1 5

610 Spring 1 08x5x25

611 Positioning Lever 1

612 Screw 1 M6x10

613 Screw 1 M6x20

614 Screw 3 M4x8

615 Flanged Shaft Sleeve 1

616 Taper Pin 1 3x30

617 Hand Lever Sleeve 1

618 Hand Lever Sleeve 1

619 Handwheel 1 Shared Piece

620 Screw 3 M4x8

621 Small Flanged Shaft Sleeve 1

622 Small Gear Shaft 1

623 Shaft Sleeve 1

624 Gear 1

625 Shaft Sleeve 1

626 Flat Key 1 5x10

627 Gear Shaft 1

628 Screw 2 M4x8

629 Nut 1 M5x30

630 Screw 1 M5x25

631 Clasp-nut 1 set

632 Pad Iron 1

633 Cylinderial Pin 2 5x12

SKU 44859

Page 24

Apron Assembly Drawing

SKU 44859

Page 25

Gear Box Parts List

ITEM # NAME QTY REMARKS

801 Change Gear 2 Z70

802 Change Gear 1 Z68

803 Change Gear 1 Z66

804 Change Gear 1 Z60

805 Change Gear 1 Z50

806 Change Gear 1 Z48

807 Change Gear 1 Z45

808 Change Gear 1 Z40

809 Change Gear 1 Z100

810 Washer 1

811 Check Ring 1 6

812 Screw 1 M5x8

813 Change Gear 1 Z30

814 Change Gear 1 Z90

815 Shaft Bolt 2

816 Nut 2 M12

817 Oil Cup 3 6

818 Change Gear 1 Z80

819 Change Gear 1 Z35

820 Open Washer 2

821 Rolling Bearing 1 12x28x8

822 Intermediate Gear 1 Z40

823 Check Ring 1 Z12

824 Outer Washer 1

825 Fixed Shaft Bolt 1

826 Washer 1 10

827 Screw 2 M5x8

828 Washer 1 6

829 Screw 1 M6x10

830 Cover 1

831 Slide Bearing 2

832 Washer 3

833 Change Gear Box 1

834 Square Nut 2

835 Screw 1 M6x35

836 Change Gear 1 Z75

837 Chang Gear 1 Z72

SKU 44859

Page 26

Gear Box Assembly Drawing

SKU 44859

Drive System Parts List

Page 27

Drive System Parts List

ITEM # NAME No.of

Teeth

1 Synchronized Drive Pulley 19 1.5 15

2 Change Gear 25 1 08

3 Spindle Pulley Ø72/102/120 02

4 Spindle Gear 40 1 02

6 Lead Screw 12TPI Right 01

8 Clearance Elimination Nut 10TPI Left 05

9 Carriage Leadscrew 10TPI Left 05

10 Cutter Rest Leadscrew 20TPI Right 04

Cutter Rest Revolving Disc

11

12 Gear 57 1 06

13 Rack 1.25 01

14 Gear Shaft 17 1.25 06

15 Clasp Nut 12TPI Right 06

16 Slotted Disc 06

17 Pin 06 Gb119 76/5x12

18 Tailstock Leadscrew 10TPI Left 03

19 Tailstock Sleeve 10TPI Left 03

21 Synchronized Counter Pulley 90 1.5 Ø51/72/100 15

22 Tension Pulley 15

24 Intermediate Gear 40 1 08

26 Change Gear 80 1 08

27 Change Gear 35 1 08

28 Change Gear 90 1 08

28-1 Change Gear 30 1 08

29 Change Gear 100 1 08

30 Synchronized Tooth Belt 118 1.5 15 B=15

31 V-Belt 15 0720

32 Motor Pulley Ø53/73/103 15

33 Motor 15 550w

34 Pinion Shaft 17 1 06

Modular

Pitch

20TPI Right 04

Thread

Hand

Dia.of Pulley Component

REMARKS

No.

SKU 44859

Page 28

Roller Bearing Parts List

ITEM # NAME Model No. Specification Qty Assembly No. REMARKS

5 Single Row Taper Roller Bearing 2007107 35x62x17 2 200 Grade D

7 Single-direction Trust Ball Bearing 8101 12x26x9 2 500

20 Single Row Annular Bearing 8101 12x26x9 1 300

23 Single Row Annular Bearing 101 12x28x8 2 1500

25 Single Row Annular Bearing 101 12x28x8 1 800

SKU 44859

Page 29

Drive System and Roller Bearing Assembly Drawing

SKU 44859

Page 30

LIMITED 1 YEAR / 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high qual­ity and durability standards, and warrants to the original purchaser that for a period of ninety
days from date of purchase that the engine/motor, the belts (if so equipped), and the blades
(if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also
warrants to the original purchaser, for a period of one year from date of purchase, that all other
parts and components of the product are free from defects in materials and workmanship (90
days if used by a professional contractor or if used as rental equipment). This warranty does
not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, con­tingent, special or consequential damages arising from the use of our product. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]

For technical questions and replacement parts, please call 1-800-444-3353

SKU 44859

REV 09g

Page 31