Page 1
200 LB. Capacity W200 LB. Capacity W
200 LB. Capacity W
200 LB. Capacity W200 LB. Capacity W
ood Cartood Cart
ood Cart
ood Cartood Cart
Model 44599
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2000 by Harbor Freight Tools®. All rights reserved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight T ools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
ITEM DESCRIPTION
Overall Dimensions (Assembled) 44”H, 30”L, 27-1/2”W at wheels,
11”W at rack frame
Net Weight 30 lbs.
Wheels Pneumatic Tires with Tube
Tire Size 2.125” x 20”
Tire Pressure 40 psi
Wheel Attachment Cotter Pin and Washer
Maximum Capacity 200 lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. K ee p
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area c lean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or pow er tools in
damp or wet locations. Don’t expose to rain. K eep work area well lighted. Do
not use electrically powered tools in the presence of flammable gases or
liquids.
3. Keep children away. Children should not be allowed to play in or around
the product.
4. Do not force product. It will do the job better and more safely at the rate
for which it was intended. Do not use inappropriate attachments in an
attempt to exceed the product’s capacity.
5. Use the right product for the right job. Do not attempt to force this
product to do the work of a larger industrial tool. There are certain
applications for which this product was designed. Do not modify this product
and do not use this product for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be
caught in moving parts. Protective, electrically non-conductive clothes and
non-skid footwear are recommended when working. Wear restrictive hair
covering to contain long hair.
7. Use eye protection. Always wear ANSI approved impact safety goggles
when assembling this product.
8. Maintain product with care. Inspect the product periodically and, if
damaged, have an authorized technician perform repairs.
SKU 44599 Page 2
Page 3
9. Stay alert. Watch what you are doing, use common sense. Do not operate
any product when you are tired.
10. Check for damaged parts. Before using an y product, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Chec k for alignment and binding
of moving parts; any broken parts or mounting fixtures; and any other
condition that may affect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician.
11. Do not operate product if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not operate
the product.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
Unpacking
When unpacking, check to make sure all parts shown on page 4 are included. If
any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Assembly Instructions
NOTE: All parts below refer to the parts listed on page 4 of this manual.
1. As shown in the diagram on page 5, position the U-Handle [1] inside the
grooves of the Axle & Frame [4]. Attach the U-Handle to the Axle & Frame
using two Bolts [10] on each side of the U-Handle. Add Washer (14) and
secure the Bolts with Nuts [13] provided.
2. Position the Left Frame [7] inside the left groove of the Axle & Frame,
opposite the end with the U-Handle attached. Secure the Left Frame using
two Nuts and Bolts as shown in the diagram. Repeat for the Right Frame [8].
3. Attach the Bracket [9] to the Left and Right Frame pieces using the
remaining Nuts and Bolts. Be sure that the folded edge of the Bracket points
in toward the U-Handle.
4. To attach the Wheels [3], slide one of the Bushing [5] pieces over the Axle
[11], followed by one of the Wheels. Secure the Wheel using a Washer [2]
and Cotter Pin [6]. Repeat for the other Wheel.
5. Insert Caps [12] into the open ends of the tubing in the U-Handle, and the
Left and Right Frame pieces.
SKU 44599 Page 3
REV 12/03
Page 4
Operation
Use your woodcart to carry heavy loads of firewood or other objects without having
to make multiple trips. Place objects in holding area between the handle and the
bracket. As always, be careful when lifting heavy objects, and do not attempt to
carry objects weighing more than 200 lbs. with this product.
Parts List
No. Description Qty.
1. U-Handle 1
2. Washer 20 2
3. Wheel Kit 2
4. Axle & Frame 1
5. Bushing 2
6. Cotter Pin 2
7. Left Frame 1
8. Right Frame 1
9. Bracket 1
10. Bolt M6 x 35 12
11. Axle 1
12. Cap 4
13. Nut M6 12
14. Flat Washer 6M 12
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 44599 Page 4
REV 12/03
Page 5
Assembly Drawing
14
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
SKU 44599 Page 5
REV 12/03
Loading...