Harbor Freight Tools 42848 Assembly And Operating Instructions Manual

Page 1
ENERGY SYSTEM SOLARENERGY SYSTEM SOLAR
ENERGY SYSTEM SOLAR
ENERGY SYSTEM SOLARENERGY SYSTEM SOLAR
PP
ANEL - 45 WANEL - 45 W
P
ANEL - 45 W
PP
ANEL - 45 WANEL - 45 W
AA
A
AA
TTTT
TT
TTTT
42848
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2000 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
ITEM DESCRIPTION
Solar Panels 15 VDC, 15 Watts each (45 watts total when connected together)
Panel Size 36-3/4” H x 13-1/4” W x 3/4” D
Flouresent Light 12 VDC, 8 Watt; Size: 12” L; Connection: two-prong
Panel Frame Size 59-1/4” x 9” x 14-3/4”
Net Weight 29.35 lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tools and/or equipment, basic safety precautions should al­ways be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.
5. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines.
6. Maintain tools with care. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician.
7. Disconnect power. To maintain efficiency of the Solar Panels, it is recommended to disconnect them from the Charge Controller at night.
8. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired.
Page 2SKU 42848
Rev 08/00 REV 09/03
Page 3
9. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician.
10. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools.
11. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician.
Note: Performance of the Solar Panels may vary depending on site location, angle of Solar Panels in relation to the arc of the Sun, and available sunlight.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under­stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 5 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
Assembly
1. Connect the Bottom Link Bar (3) to the Left Triangle Frame (1) and the Right Triangle Frame (2) using the attached bolt and hook.
Upper Link Bar (4)
Left Triangle Frame (1)
Bottom Link Bar (3)
2. Connect the Upper Link Bar (4) to the Left Triangle Frame (1) and the Right Triangle Frame (2) using the attached bolt and hook.
Right Triangle Frame (2)
3. Tighten both frame bolts to stabilize the frame assembly.
4. Locate the frame assembly so that if faces the sun the greater part of the day.
Page 3SKU 42848
Page 4
5. Secure the frame assembly to its mounting location using hardware (not supplied) through the four holes on the bottom of the Left and Right Triangle frame.
6. Carefully place each Solar Panel (5) on the front of the frame assembly so that the bottom of each panel fits into the slot on the bottom of the frame assembly.
7. Lock the two eye hooks on the back-center frame into the two protruding bolts on the Upper Link Bar (4).
Plug connectors into panels here
Wire Panel Connectors (6)
Connect wires to the Charge Controller (8). Refer to wiring diagram
Eye Hooks
8. Attach the Wire Panel Connectors (6) to each connector on the panels.
The short cable connector must be connected to the center panel connector.
9. Mount the Charge Controller near the Solar Panels.
This controller should be protected from the weather.
10. Connect the Solar Panels, Lamp, and 12 VDC (rechargeable) Battery (not included) as shown above. (Also refer to the wiring diagram on page 6.)
Connections to the Charge Controller require you to press down on the red or black
tabs while inserting the stripped wire into the holes. You should not be able to pull the wire out after releasing the tab.
The Lamp wires can be spliced to a longer cord of the same type if the Lamp is to be
used at a distance from the Charger Controller.
11. Mount the Lamp using screws (not supplied).
Page 4SKU 42848
REV 09/03
Page 5
Operation
1. Press the Lamp Switch to the ON position.
In the daytime when light is shining on the Solar Panels the Lamp is powered from the
electricity produced by the Solar Panels (“Panel” indicator will light on the Charge Controller).
The “Over Charge” indicator will light when the Solar Panel voltage goes over 15 volts.
The “Over Discharge” indicator will light when the Solar Panel voltage goes below 11 volts. At night, the Lamp is powered by the Battery.
2. When finished with the Lamp, press the Lamp Switch to the OFF position.
3. To maintain a high level of efficiency of the Solar Panels, it is recommended that you disconnect the Solar Panel cable from the Charger Controller at night.
Maintenance
1. With the Solar Panel cable disconnected from the Charger Controller, periodically clean the Solar Panels with mild soap and water.
2. Periodically check all cable connections.
Parts List
#metInoitpircseDytQ
1emarFelgnairTtfeL1 2emarFelgnairTthgiR1 3raBkniLmottoB1 4raBkniLreppU1 521/51PAS,lenaPraloS3 6srotcennoClenaPeriW1 7elbaCyrettaB1 8rellortnoCegrahC1
9
NOTE: Some parts are listed and shown for illustra­tion purposes only and are not available individually as replacement parts.
hctiwSedilShtiwW51
-LFCD,thgiLtnecseroulFCD
1
Page 5SKU 42848
Page 6
Wiring Diagram
Page 6SKU 42848
REV 09/03
Page 7
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALI­FIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 7SKU 42848
REV 09/03
Loading...