Harbor Freight Tools 37350 Product manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

REV 15c

Visit our website at: http://www.harborfreight.com

Email our technical support at: productsupport@harborfreight.com

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

Specifications

Electrical Rating 15 A

Bulb

12 V 55 W H3 Halogen

(included)

IMPORTANT SAFETY INFORMATION

Installation Precautions

1. A 15 amp fuse must be installed inline on the positive power supply wire of this item. Using no fuse, or using an incorrect fuse can cause an electrical fire.

2. Install only according to these instructions.

Improper installation can create hazards.

3. Wear ANSI-approved safety goggles and

heavy-duty work gloves during installation.

4. Make certain the vehicle’s engine is

turned off and battery is disconnected before installing the Lights.

5. When drilling holes, beware of any

hidden electrical lines or cables. Make sure you don’t damage or weaken the structural integrity of the vehicle.

6. Vehicles equipped with airbags may

have the sensors located inside the front bumper. Consult the vehicle owner’s manual to determine the location of the airbag sensors. To avoid damaging the sensors if they are located in the front bumper, do not drill holes in the bumper.

7. Do not install Lights where they could restrict

sufficient airflow to the radiator or obstruct the headlights and/or turn signals of vehicle.

8. Keep installation area clean and well lit.

9. Keep bystanders out of the

area during installation.

10. Do not install when tired or when under the influence of alcohol, drugs or medication.

11. Read all instructions and safety precautions in the vehicle’s manual onto which the Lights will be installed.

12. Install on negative ground 12 VDC systems only.

13. Do not install this product yourself unless you are technically competent to do so. If necessary, have a qualified technician install the Lights.

14. WARNING: The cord of this product contains lead and/or di (2-ethylhexyl) phthalate (DEHP), chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)

15. WARNING: This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.)

16. WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.)

Use Precautions

1. This product is not a toy. Do not allow children to play with this item.

2. The Halogen Lights become very hot during continuous use. Do not touch the Lights for at least half an hour after turning off.

Page 2 For technical questions, please call 1-888-866-5797. Item 37350

3. Inspect before every use; do not use if parts are loose or damaged.

4. Use as intended only. Do not modify this product or use it for a purpose for which it was not intended.

5. This product may not meet D.O.T. requirements for use on public roads or highways. Follow local, state, and federal regulations.

6. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator.

Installation Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to Parts List and Diagram on page 6.

Light Mounting

1. To avoid accidental short circuits, disconnect the negative (-) terminal of the vehicle battery prior to installation.

2. Driving lights must be mounted between 16" and 42" from the ground. Fog lights must be mounted between 12" and 30" from the ground. Check state and local regulations for minimum and maximum mounting height requirements.

3. The Halogen Lights can be mounted above or below the bumper. Make sure the desired mounting locations do not obstruct the vehicle’s headlights or turn signals.

4. If mounting below the bumper, perform following procedure to maintain the optimum beam pattern:

a. Remove two Screws (18) from the sides

of each Light Housing (9). Remove the Lens Holder (1) and Glass Lens (3) from the front of each Light.

b. Pull out the Reflector (8) from the Light

Housing, turn 180 º and put back into

the Housing in the reverse position.

c. Turn the Glass Lens 180 º, reinstall on

the Light Housing and secure in place with the Lens Holder and Screws.

5. Place the Halogen Lights on the bumper, and mark the desired mounting locations at an equal distance from the center of the bumper.

6. Drill 1/2" diameter holes through pre-marked mounting positions.

CAUTION: Make sure no electrical wires or cables are in the way of the drilling path.

7. Install the Lights on the bumper, using the Bolts (17), Lock Washers (15), and Nuts (16).

8. Loosen Bolts (12) on the sides of the Mounting Bracket (14) of each Light and align to desired angle. Tighten the Bolts to retain aiming position.

9. Mount the Light Switch (19) in a location that is within easy reach (i.e., dashboard, console). With the Light Switch in the desired position, mark the holes for drilling and drill two 1/16" holes. Mount the Light Switch with the Screws provided.

Page 3For technical questions, please call 1-888-866-5797.Item 37350

+ 5 hidden pages