4-1/2” ANGLE GRINDER
®
Model 03150
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
Copyright 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
PRODUCT SPECIFICATIONS
(
)
y
Item Description
Electrical Requirements 120 Volt/60 Hz/580 Watts/12,000 RPM/
4.8 Amps Maximum
Grinding Wheel Size
Not Included
Spindle Size 5/8” – 11 TPI
Accessories Auxiliary Handle (Qty. 1)
4-1/2” Diameter, 7/8 Arbor
Wrench (Qty. 1)
Carbon Brush (Qt
. 2)
E194601
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the
inside of the front cover. Keep this manual and invoice in a safe and dry place for
future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
SKU 03150 PAGE 2
3. Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
4. Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
5. Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation eliminates the need for the
three wire grounded power cord and grounded power supply system.
6. Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
7. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock.
9. When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10. Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operat-
ing power tools may result in serious personal injury.
SKU 03150 PAGE 3
11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
12. Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
13. Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
14. Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
15. Use safety equipment. Always wear eye protection. Dust mask, nonskid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
16. Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
17. Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
18. Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
19. Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
20. Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
21. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
SKU 03150 PAGE 4
22. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly main-
tained tools.
23. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
24. Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
25. When servicing a tool, use only identical replacement parts. Follow
instructions in the
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
“Inspection, Maintenance, And Cleaning”
section of this
SPECIFIC SAFETY RULES
1. Always use proper guard with grinding wheel. A guard protects the operator
from broken wheel fragments.
2. Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live” and shock the
operator.
3. Maintain labels and nameplates on the Polisher/Waxer. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
4. Always wear safety impact eye goggles and heavy work gloves when using
this tool. Using personal safety devices reduce the risk for injury. Safety impact
eye goggles and heavy work gloves are available from Harbor Freight Tools.
5. Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use a power tool in areas
near flammable chemicals, dusts, and vapors. Do not use this product in a damp or
wet location.
6. WARNING! All accessories for this tool must be rated for at least 12,000
RPM. Grinding Wheels and other accessories running over the rated 12,000 RPM
speed can fly apart and cause injury.
7. When using a handheld power tool, always maintain a firm grip on the tool
with both hands to resist starting torque.
8. Use only 4-1/2” diameter Grinding Wheels that having a 5/8” center mounting hole.
Never disable or modify the Wheel Guard.
SKU 03150 PAGE 5
REV 01/04REV 04/06
8. Avoid unintentional starting. Make sure you are prepared to begin work
before turning on this tool.
9. Do not force this tool. This tool will do the work better and safer at the speed
and capacity for which it was designed. Do not force the rotating Grinding Wheel
(not included) into the object being ground. Apply moderate pressure, allowing
the Grinding Wheel to rotate freely without being forced.
10. WARNING! Never install a carbide tipped or steel circular saw blade
for use on this tool. Never install a wood carving blade, carving disc with
saw chain cutters, or a cutting carving disc on this tool.
11. For safest operation, it is recommended that only these accessories be
used with this tool: Abrasive Cut-Off Discs and Wheels, Flap Wheels, Wire
Brushes, Wire Wheel Brushes.
12. Never lay this tool down until the Rotating Grinding Wheel has come to a
complete stop. The Rotating Pad can grab the surface and pull the tool out of
your control.
13. Never leave this tool unattended when it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its electrical outlet beforeleaving.
14. Always unplug this tool from its electrical outlet before performing inspec-
tion, maintenance, or cleaning procedures.
15. WARNING! Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica
from bricks and cement or other masonry products, arsenic and chromium from
chemically treated lumber. Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq.)
16. WARNING! People with pacemakers should consult their physician(s)
before using this product. Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference or failure of the pacemaker.
SKU 03150 PAGE 6
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.)
2. The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
3. Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration. (See Figure A.)
FIGURE A
SKU 03150 PAGE 7
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
4. Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code. (See Figure B.)
5. Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
FIGURE B
EXTENSION CORDS
1.
2. As the distance from the supply outlet increases, you must use a heavier gauge
3. The smaller the gauge number of the wire, the greater the capacity of the cord.
4. When using more than one extension cord to make up the total length, make
Grounded
can use either a two or three wire extension cord.
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C, next page.)
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
sure each cord contains at least the minimum wire size required.
(See Figure C.)
tools require a three wire extension cord.
Double Insulated
tools
5. If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
SKU 03150 PAGE 8
6. If you are using an extension cord outdoors, make sure it is marked with the
(
)
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
7. Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
8. Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
NAMEPLATE
AMPERES
At Full Load
25
Feet
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - * Based on limiting the line voltage drop
FIGURE C
to five volts at 150% of the rated amperes.
EXTENSION CORD LENGTH
50
Feet
75
Feet
100
Feet
150
Feet
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
V ~
A
n
o
xxxx/min.
SKU 03150 PAGE 9
Volts Alternating Current
Amperes
No Load Revolutions
per Minute (RPM)
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 12
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY AND OPERATING INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer
to the
1. WARNING! Always make sure the Power Cord (part #50) of the Angle
2. To install a 4-1/2” diameter Grinding Wheel (not included), depress the Stop Pin
Assembly Diagram on page 13.
Grinder is unplugged from its electrical outlet
prior
to adding any accessories or
making any adjustments to the tool.
(part #11) to keep the Spindle (part #27) from turning. Insert the Wrench
(part #58) into the two holes located in the Flange Nut (part #32). Unscrew and
remove the Flange Nut. Then, release pressure on the Stop Pin.
(See Figure D.)
3. Insert the 4-1/2” diameter Grinding Wheel fully onto the Spindle (part #27),
making sure the Grinding Wheel fits snugly against the inner Flange (part #30).
Depress the Stop Pin (part #11) to keep the Spindle (part #27) from turning.
Make sure the Flange Nut (part #32) is firmly retightened onto the Spindle.
Then, release pressure on the Stop Pin. (See Figure D.)
POWER SWITCH (#39)
BRUSH HOLDER (#40)
CARBON BRUSH (#41)
FIGURE D
BRUSH CAP (#42)
WRENCH (#58)
STOP PIN
(#11)
GEAR BOX
(#15)
HANDLE
(#16)
INNER FLANGE
(#30)
INSERT
4-1/2”
GRINDING
WHEEL
ONTO
SPINDLE
(#27)
FLANGE NUT (#32)
SKU 03150 PAGE 10
4. To attach the Handle (part #16), screw the threaded portion of the Handle into
either the right or left side threaded mounting hole located on the sides of the
Gear Box (part #15). (See Figure D.)
5. To operate the Angle Grinder, plug the Power Cord (part #50) into a grounded,
120 volt, electrical outlet.
6. Grip the Angle Grinder firmly with
(part #39) to its “ON” position and allow the Grinding Wheel to rotate to its fullest
speed. (See Figure D.)
7. Do not force the rotating Grinding Wheel into the object being ground. Apply
moderate pressure, allowing the Grinding Wheel to rotate freely without being
forced.
8. After the grinding job is completed, turn the Power Switch (part #39) to its “OFF”
position. Then unplug the Power Cord (part #50) from its electrical outlet.
both hands. Then turn the Power Switch
INSPECTION, MAINTENANCE, AND CLEANING
1. WARNING! Make sure the Power Switch (part #39) of the Angle Grinder is
in its “OFF” position and that the tool is unplugged from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.
2. BEFORE EACH USE, inspect the general condition of the Angle Grinder. Check
for loose screws, misalignment or binding of moving parts, cracked or broken
Grinding Wheel, damaged electrical wiring, and any other condition that may
affect its safe operation. If abnormal noise or vibration occurs, have the problem
corrected before further use.
Do not use damaged equipment.
3. PERIODICALLY, the two Carbon Brushes (part #41) should be checked. If the
Carbon Brushes are simply dirty, they may be cleaned by rubbing them with a
pencil eraser. If the Carbon Brushes are excessively worn, they must both be
replaced at the same time. To clean or replace the Carbon Brushes, unscrew
and remove the Brush Caps (part #42) to expose the Carbon Brushes. Pull out
both Carbon Brushes from their Brush Holders (part #40), and insert two new
Carbon Brushes in the Brush Holders. Then, replace the Brush Caps.
(See Figure D.)
4. Use only a clean cloth and mild detergent to clean the body of the
Angle Grinder. Do not use solvents. Do not immerse any part of the tool in
liquid.
SKU 03150 PAGE 11
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part # Description Part # Description
1 Spring 30 Flange
2 Spring Washer 31 Grinding Wheel
3 Washer 32 Flange Nut
4 Nut 33 Screw
5 Pinion Gear 34 Screw
6 Bearing 35 Stator
7 Bearing Cap 36 Cabinet
8 Roller 37 Switch Knob
9 Armature 38 Switch Shelf
10 Bearing 39 Power Switch
11 Stop Pin 40 Brush Holder
12 Screw 41 Carbon Brush
13 Screw 42 Brush Cap
14 Screw 43 Cord Protector
15 Gear Box 44 Screw
16 Handle 45 Back Cap
17 Check Ring 46 Cord Clamp
18 Bearing 47 Screw
19 Check Ring 48 Screw
20 Gear 49 Screw
21 Bearing Cap 50 Power Cord
22 Bearing 51 Washer
23 Front Cap 52 Screw
24 Screw 53 Condenser
25 Screw 54 Inductor
26 Wood Ruff Key 55 Rubber Bearing Shoe
27 Spindle 57 Ring
28 Screw 58 Wrench
29 Guard
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 03150 PAGE 12 REV 11/04
REV 04/06
16
12
13
14
15
20
21
22
18
19
ASSEMBLY DIAGRAM
11
1
2
3
5
7
17
33
4
6
2
35
8
34
9
54
58
10
23
24, 2, 3
26 27
28
29
30
31
32
25, 2, 3
54
42
43
36
40
41
45
53
44
50
46
51
2
52
37
55
47
38
39
49
57
48
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 03150 PAGE 13
REV 04/06
Loading...