Page 1
MAGNETIC PAINTER’S
®
WORKSTATION
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
04/03
Page 2
SPECIFICATIONS
ITEM
Open Dimensions
Net Weight
Finish
Materials
Weight Capacity
22-3/4” Long X 13-1/8” High X 9” Wide
11.90 Lbs.
White Painted
Formed Steel Metal, Vinyl Coated Magnetics, Pre- drilled and Machined Holes
30 Lbs.
DESCRIPTION
The Magnetic Painter’s Workstation is ideal for holding a spray gun and other
work components while painting.
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover.
Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1. KEEP PRODUCT USAGE AREA CLEAN. Keep area free from moisture or oil.
Cluttered areas invite injuries.
2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children
to handle this product.
3. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged parts and
any other conditions that may affect its operation. Replace or repair damaged or worn
parts immediately.
4. REPLACEMENT PARTS AND ACCESSORIES. Use only identical replacement parts.
5. WEAR SAFETY GOGGLES (Must comply with ANSI) at all times when assembling.
6. AVOID SHARP EDGES WHEN ASSEMBLING. Avoid pinching fingers when opening
and closing Tray. Avoid edges while using as they may puncture skin.
7. WEAR APPROVED BREATHING MASK AROUND PAINT FUMES. DO NOT SMOKE
or have open flames around Painter’s Workstation or spray booth.
8. FOLLOW ALL INSTRUCTIONS AND SAFETY PRECAUTIONS of the tools you are
using in conjunction with the Painter’s Workstation.
SKU 03648 PAGE 2
Page 3
ASSEMBLY INSTRUCTIONS
1. On the Backside (#1) of the Magnetic Painter’s Workstation, peel off the protective tape
from the Magnetic Strips and discard. See Figure A
#1
Magnetic
Strips
Figure A
Figure B
2. Mount the Magnetic Painter’s Workstation with it’s folding Tray (#2) on the metal spray
booth wall. The Magnetic Strips allow you to place the Workstation within easy reach. It
can hold your spray gun in slotted paint gun holder. Notched areas on Tray can hold other
tools. After mounting the Workstation, double check that it is tightly secured to the booth’s
wall before using.
3. When not being used, you can fold Tray (#2) up flat against the wall. See Figure C.
#8
#9
#2
Figure C
Figure D
4. To remove Magnetic Painter’s Workstation from a metal surface, lift the Handle (#9)
and the Offset Wheel (#8) will push Workstation away from the surface and it will
release the magnetic pull. See Figure D.
5. If you choose, you can mount the Magnetic Painter’s Workstation on a wall using
screws or nails (not provided). Note: This wall surface must be capable of supporting
the weight of the Workstation and all related tools. Choose hardware that will fit into
the holes on the back of the station. The dimension of the holes are 3/16” wide
(narrowest portion) and 3/8” for the head of the screw or nail. Caution: Do not overload
Workstation. See Figure E.
Holes
SKU 03648 PAGE 3
Holes
Figure E
Page 4
PARTS LIST
PART # DESCRIPTION QTY
1
2
3
4
5
6
7
8
9
Backside with Magnets
Tray
Bolt M5 X 10
Lock Nut M5
Spring
Lock Nut M5
Bolt M5 X 30
Offset Wheel
Handle
#3
#4
#2
#1
nail or screw holes
#9
#8
1
1
2
2
1
1
1
1
1
#7
#6
#3
#4
#5
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry.
2. Periodically check to see that all hardware is in place.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
SKU 03648 PAGE 4
Loading...