Harbor Freight Tools 02893 Assembly & Operating Instructions

®

TELESCOPIC TRIPOD

WITH CAR MOUNT

02893

ASSEMBLY & OPERATING INSTRUCTIONS

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s
record below:

Model

___________ Serial No._____________ Purchase Date_____________

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions, operating
and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the
invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry
place for future reference.

Technical Specifications

Product Name: Telescopic Tripod with Car Mount
Product Number: 02893

Construction: Aluminum Alloy
Standing Height-Flat Surface: 11.4-17 Inches
Mount Thread Diameter 1/4 “
Maximum Weight
of Mounted device: 4.5 Lbs.
Length-Folded: 13.7"
Weight: 12 OZ.

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use this product in damp or wet locations. Don’t
expose to rain. Keep work area well lighted.

3. Store idle equipment. When not in use, products must be stored in a dry location to inhibit
rust. Always lock up products and keep out of reach of children.

4. Use the right product for the job. There are certain applications for which this product was
designed. It will do the job better and more safely at the rate for which it was intended. Do not
modify this product and do not use this product for a purpose for which it was not intended.

5. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and
any other condition that may affect proper operation. Any part that is damaged should be
properly repaired or replaced by a qualified technician.

#02893 Page 2

6. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty. Only use accessories intended for use with this
product. Approved accessories are available from Harbor Freight Tools.

7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the product.

8. When using Car Window Mount accessory, make certain that electric car windows remain in a
fixed position. Rolling up the window may result in damage to the window, camera and Window
Mount.

9. The camera mount is designed to support an average weight camera; never attempt to mount a
camera weighing more than 4.5 lbs.

Warning: The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be
supplied by the operator.

Assembly

Your Telescopic Tripod with Car Mount will require some assembly prior to use. It is important that
you read the entire manual to become familiar with the unit BEFORE you use the Tripod. Before
assembling your Telescopic Tripod be sure that you have all parts described in the Parts List located
on the last pages of this manual.

Standard Setting

Step 1) Spread out the three (3) Legs (#1) of the Telescopic Tripod. Set the Tripod down at

the point that you will be viewing from-see Figure 1.

Step 2) Insert the Mounting Screw (#2) up into the threaded mounting receptacle in your

camera. Turn the Mounting Screw Knob (#3) clockwise until the camera is securely
in place on the Tripod-See Figure 2.

Step 3) Raise or lower the Center Post (#4) by loosening the Clamping Lever (#5), adjusting

the Center Post (#4) and tightening the Clamping Lever (#5) into place.

Figure 1-Standard Tripod Use

Center Post (#4)

Clamping Lever (#5)

Handle (#7)

Legs (#1)

#02893 Page 3

Step 4) The camera can be tilted to different viewing angles from + 95 degrees to -55

degrees. To tilt the camera, loosen the Two-Finger Knob (#6) opposite the
Handle (#7)-see Figure 2. Use the Handle (#7) to angle or rotate the camera.
Tighten down the Two-Finger Knob (#6) into desired position.

Setting Up the Car Mount

Step 1) Loosen the Two-Finger Knob (#6) and separate the Legs (#1) and Center Post (#4)

from the top of the Tripod body. Insert the threaded portion of the Car Mount (#8)
into the Two-Finger Knob (#6) as shown in Figure 2.

(camera not included)

Mounting Screw Knob (#3)

Two-Finger Knob (#6)

Car Mount (#8)
with Knob

Figure 2-Car Mount

Step 2) Set the Car Mount (#8) over the lip of the window and tighten the Car Mount Knob

until the Car Mount and camera sit securely in place-as in Figure 3.

(camera not included)

car window

Figure 3

Warning: Never attempt to use the product while driving a vehicle.

Make certain that the camera and Telescopic Tripod with Car Mount are securely
mounted to the lip of the window and that the strap is held while taking pictures from
a vehicle.

Warning: The camera mount is designed to support an average weight camera; never attempt

to mount a camera weighing more than 15 lbs.

Using the Arm Brace

Step 1) With the Legs (#1) of the Tripod attached, insert two Legs (#1) together into both

loops of the Arm Brace (#11)-see Figure 4. Insert the third Tripod Leg (#1) into the
opposite loop of the Arm Brace (#11)-see Figure 4.

Step 2) Rest the Arm Brace (#11) over your forearm, while grasping the Handle (#7).

View your object thorugh the lens of your camera and take pictures. Adjust settings

#02893 Page 4

as necessary.

Handle (#7)

Legs (#1)

Arm Brace (#11)

Figure 4-Using the Arm Brace

Operation

To assist you with operation please refer to the Operational Figures as well as the Parts List and
Assembly diagram located on the last pages of this manual.

Do not attempt to support more than the maximum weight of 4.5 Lbs. on the Telescopic Tripod.

Position and support the camera safely and securely before using the product.

Unpacking

Unpack and Check Contents

When unpacking your Telescopic Tripod with Car Mount, check to make sure the following parts are
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS
at 1-800-444-3353.

Parts List

Part # Description Quantity Part # Description Quantity

1 Leg 3 7 Handle 1
2 Mounting Screw 2 8 Car Mount with Knob 1
3 Mounting Screw Knob 1 9 Leg Boots 3
4 Center Post 1 10 Storage Bag 1
5 Clamping Lever 1 11 Arm Brace 1
6 Two-Finger Knob 1

Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.

#02893 Page 5

Assembly/Parts Diagram

2

3

6

4

7

5

10

8

11

1

9

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

#02893 Page 6