Hanwha Techwin SSA R2000V User Manual

RFID Reader

User Manual

SSA-R2000V

RFID Reader

User Manual

Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.

Tra de mark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this docu­ment shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung
Tec hwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without
prior notice.

Warrant y

If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:

If the system behaves abnormally because you run a program irrelevant to the system operation.

•
Deteriorated performance or natural worn-out in process of time

•
Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)

•

is the registered logo of Samsung Techwin Co., Ltd.

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.

This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

WARNING

To reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.

•

WARNING

1.

Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet.
Using any other adapter could cause fi re, electrical shock, or damage to the product.

2.

Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to
the product.

Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.

3.

4.

Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.

5.

When installing the controller, fasten it securely and fi rmly. The fall of controller may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the

6.
controller. Doing so may cause personal injury due to fi re, electric shock, or falling objects.

7.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.

8.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.

9.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.)

10.

. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.

CAUTION

1.

Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive
vibration or magnetic interference.

2.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -30°C), or high humidity.
Doing so may cause fi re or electric shock.

3.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

4.

Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage
to the product.

5.

Keep out of direct sunlight and heat radiation sources. It may cause fi re.

6.

Install it in a place with good ventilation.

7.

Avoid aiming the controller directly towards extremely bright objects such as sun.

8.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be
placed on the apparatus.

9.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English _ 3

SAFETY INFORMATION

safety information

FCC Statement

Caution : Any changes or modifi cations in construction of this device which are not expressly approved by the

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

party responsible for compliance could void the user’s authority to operate the equipment.

This device may not cause harmful interference, and

1)

This device must accept any interference received, including interference that may cause undesired operation.

2)

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, any cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that
produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for
replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

Only use attachments/accessories specifi ed by the manufacturer.

Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with
the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

combination to avoid injury from tip-over.

Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any

way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4_ safety information

contents

PRODUCT INTRODUCTION

6

INSTALLATION AND EXTERNAL

CONNECTION

9

INITIALIZATION

12

OUTPUT FORMAT

13

TROUBLESHOOTING

6 Features
6 What’s included
7 At a Glance
8 Cable Color Scheme
8 Cable Selection

9 Installation
10 Precautions on installation
11 External Connection

12 Basic Operations

13 Wiegand Output
14 RS-232 Output
15 8 Bit Burst Output Format

16 Troubleshooting

CONTENTS

16

PRODUCT SPECIFICATIONS

17

17 Product Specifi cations

English _ 5

product introduction

FEATURES

This model is an elegant-looking proximity reader that is featured by the capacitive touch-sensing keypad. The back-lighted
keypad is useful especially for night operation, and its epoxy adhesion and aluminium case relieve you of worries about the
rain or any other challenging weather conditions. This model permits user access through authentication of the presented
proximity card and personal identifi cation number using the keypad. With its red, green and orange indicators as well as the
Piezo buzzer, this model is guaranteed to make a stable and correct operation.

◆

125 KHz Proximity / PIN Reader

◆

PSK Modulation

◆

26 bit Wiegand/RS-232 Data Output

◆

8 Bit Burst Output Format supported

◆

Numeric Keypad with Backlighting for Night Operation

◆

Control of External LED Indicators

◆

Control of External Buzzer

◆

Tamper Switch

◆

Reverse Polarity Protection

◆

Weatherproof and Dustproof

WHAT’S INCLUDED

Check if the following items are included in the product package.

SSA-R2000V

Product

Quick Guide 3mm Hex Wrench (x1)

6_ product introduction

3.5 x 40mm Screws (x4)

3.5 x 25mm Screws (x4)

6 x 30mm Plastic Anchor (x4

CD Manual

AT A GLANCE

Front/Rear

PRODUCT INTRODUCTION

3

4

5

SSA-R2000V

6

LED

1

Keypad

2

Tamper Switch

3

Connection Cable

4

Buzzer

5

Fixing Hole

6

Displays the status of the system operation.

Used to enter the ID/password.

A tamper switch to detect falling from the wall.

Used to connect to the power source or I/O cable.

Piezo buzzer.

Fixing hole for wall-mounting.

English _ 7

product introduction

CABLE COLOR SCHEME

Item Cable Color Signal Line Description

Power

Output

Not used

Input

Tamper

Red DC +12V Power (+12V)

Black GND Earth-grounding for power

Green WIK_DATA0 Wiegand Data 0 Output Port

White WIK_DATA1 Wiegand Data 1 Output Port

Purple TX_OUT

Orange RS-232 GND

Brown NC

Yellow Green LED Control

Gray Orange LED Control

Blue Buzzer Control BUZZER Control Input Port

Pink Tamper COM

Light yellow Tamper NC

CABLE SELECTION

Item Cable Type

Power (DC12V)

1

Card/PIN data (Wiegand)

Control Signal (LED,BUZZER)

2

TAMPER

RS-232 Cable

3

΃΄΀ΦΥΡΦΥ΅ΖΣΞΚΟΒΝ

΃΄͸ΣΠΦΟΕΚΟΘ΅ΖΣΞΚΟΒΝ

ͿΠΥΦΤΖΕ

͸ΣΖΖΟͽͶ͵ʹΠΟΥΣΠΝͺΟΡΦΥ
΅ΖΣΞΚΟΒΝ

΀ΣΒΟΘΖͽͶ͵ʹΠΟΥΣΠΝͺΟΡΦΥ
΅ΖΣΞΚΟΒΝ

ʹ΀;΁ΠΣΥΠΗ΅ΒΞΡΖΣ΄ΨΚΥΔΙ

Ϳʹ΁ΠΣΥΠΗ΅ΒΞΡΖΣ΄ΨΚΥΔΙ

Belden #9409, 18 AWG 2 Conductor, Unshielded

Belden #9512, 22 AWG 4 Conductor, Shielded

Belden #9514, 22 AWG 8 Conductor, Shielded

Belden #9829, 24 AWG 2-twisted pair, Shielded

8_ product introduction

installation and external connection

INSTALLATION

See [Figure 1] to drill 6-32” holes and 1/2” holes (totally 4) into the wall.

1.

Tighten the four screws to secure the product to the wall.

2.

With the provided 3mm hex wrench, fi x the outer case to the product.

3.

INSTALLATION AND EXTERNAL CONNECTION

81.80

93.00

85.50

0.00

99.80

72.50

54.50

36.50

18.50

6.00

91.50

30.30

40.00

26.23

40.30

50.30

60.30

Ø1.50

72.80

Ø1.00

69.10

79.60

100.80

86.50

4.35cm

8.7cm

4.35cm

6-32 hole

Reader Module

4cm

6.4cm

6-32 hole

6-32 or M3 Screws

1/2˝ hole

SSA-R2000V

1.00

20.30

8.30

Ø1.00

Ø1.50

12.50

Bezel

64.00

7.80

0.00

8.30

18.30

31.30

49.30

56.30

62.30

72.30

80.60

3mm Hex Wrench

[Figure 1] [Figure 2]



English _ 9

installation and external connection

PRECAUTIONS ON INSTALLATION

IF INSTALLING ON A METAL WALL

If you install the reader on a metal wall, the read range may be reduced.
To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown

below.

Metal

Wall

Spacer

SSA-R2000V

Reader

IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK

If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if
you present a card to one reader, the other reader may recognize the same card, meaning both readers read the
same card simultaneously.

To avoid this problem

#Reader 2

, keep at least 20cm of space between the two readers.

Minimum

20cm

0V

200

R

-

A

SS

V
000
2

R

-

A
S
S

#Reader 1

BACK TO BACK

<Front and Back>

INSTALLATION

0V

0

0

2

R

-

A

SS

#Reader 1

Minimum

20cm

#Reader 2

SIDE BY SIDE

<Side by Side>

INSTALLATION

10_ installation and external connection

EXTERNAL CONNECTION

WIRING DIAGRAM

Green

White

Light yellow

Pink

Blue

Yellow

Gray

CONTROLLER

Wiegand Data 0 Out

Wiegand Data 1 Out

Tamper Switch Out(NC)

Tamper Switch Out(COM)

Buzzer Control In

LED Control In(Green)

LED Control In(Orange)

Category Cable Wiring

Connect the DC+12V to the red line.

Power Supply Unit

Connect GND to the black line.

Connect the green line of the product to the Wiegand D0 input port of the controller.

Wiegand Connection

Connect the white line of the product to the Wiegand D1 input port of the controller.

Enables you to turn on or off the LED indicators.

LED Control

To control the green indicator, connect the yellow line; to control the orange indicator, connect the blue line
with white stripes, to the output port of the controller. (see page 12)

Buzzer Control

Tamper Control

RS-232 Connection

Enables you to turn on or off the buzzer.
To control the buzzer, connect the blue line to the controller’s output (relay).

Connect the COM port (Pink line) of the product’s tamper switch to GND; connect the NC port (Light yellow)
of the tamper switch to the input port of the controller.

Connect to the COM port of the PC. (Connect pin 2 of the DB-9 connector to the purple line; connect the
orange line to pin #5 of the DB-9 connector)

SSA-R2000V

SSA-R2000V

Red Black

DC +12V GND

POWER

RS-232(TX)

Purple

RS-232(GND)

Orange

(see page 12)

INSTALLATION AND EXTERNAL CONNECTION

PC

English _ 11

initialization

BASIC OPERATIONS

Initial State (when the power is supplied)

When you apply power to the product, it will sound beep three times before entering Standby with the red indicator
turned on.

Using the card

Present the card to the product until you hear a beep and the green indicator turns on.
The reader keeps the green indicator turned on while transferring the card data to the
controller. When it is done, the green indicator turns off and for receiving the next card,
the red indicator stays ON.

Using the keypad

Hold down the keypad until you hear a beep. The reader transfers the keypad data to the controller.

As soon as you press the keypad, the orange indicator turns on, followed by the reader transferring the keypad data
to the controller. Then, only the red indicator turns on.

LED Control

You can control both green and orange indicators at will.
To control the green indicator, connect the green-indicator control line (yellow) to NO of the controller relay output,
and connect COM to GND. Set I/O of the controller; now you can control turning on/off the indicator.
You can turn on/off the indicators according to the I/O settings of the controller, which can be applied to various
situations. For more information about the I/O settings of the controller, refer to the user manual of the controller.
To control the orange indicator, connect the gray line to NO of the controller.

Card

X

[

Y
^
\

Z

l
zj

_

i

]



W

`

lz
j

z
z
hTz

Y
W
WW

SSA-R2000V

Buzzer Control

Connect the buzzer control input line (blue) to the NO port of the controller relay output, and GND to the COM port.
You can confi gure the I/O settings of the controller so that it beeps. If the product continues to beep, it means that
the buzzer control is working properly.

The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized
or unauthorized access upon user authentication.

Furthermore, you can make various modifi cations according to the different I/O settings of the controller.
For more information about the I/O settings of the controller, refer to the user manual of the controller.

Card reading is not available while the buzzer control is sounding the buzzer.

Tamper Control

You can set the signal that you want to output if the device is dismantled forcibly.
Connect the COM port (Pink line) of the product’s tamper switch to GND; connect the NC port (Light yellow) of the

tamper switch to the input port of the controller. If the tamper of the reader operates, the controller produces an input
signal and generates the corresponding output depending on the controller setting.

12_ initialization

output format

WIEGAND OUTPUT

Timing Diagram

100us

OUTPUT FORMAT

DATA-0

1ms

DATA-1

123
0LOGIC 1 1 1 0 0

Data Type (26-bit)

Bit 1 : Even Parity (bit 2 ~ bit 13)

•

Bit 2 ~ 9 : Facility Code (000 ~ 255)

•

Bit 10 ~ 25 : ID Number (00000 ~ 65,535)

•

Bit 26 : Odd Parity (bit 14 ~ bit 25)

•

5V

0V
5V

0V

n-2 n-1 n *n : 34 or26

English _ 13

output format

RS-232 OUTPUT

Output Waveform

+15V

Space(=0)

+3V

0V

-3V

Mark(=1)

-15V

Data Type

START (0X02H) DATA (8 Char) END (0x03H) LRC

START(0X02H) DATA (1~8 Char) END (0x03H) LRC



M



LSB

01 100000 0

8 Data Bits

Start Bit

Check the following settings:
Baud Rate : 9600bps
Data Bit : 8
Parity Bit : None
Stop Bit : 1

LRC : This is the result of XOR operation of each byte from Start to End.

Data packet corresponding to ASCII character ‘A’

MSB

2 Stop Bits

Indeterminate

Region

14_ output format

8 BIT BURST OUTPUT FORMAT

8Bit Burst Output Format

Keypads Binary Hexa Keypads Binary Hexa

0 11110000 F0

1 11100001 E1

2 11010010 D2

3 11000011 C3

4 10110100 B4

5 10100101 A5

6

7

8

9

ESC

ENT

10010110

10000111

01111000

01101001

01011010

01001011

96

87

78

69

5A

4B

OUTPUT FORMAT

English _ 15

troubleshooting

TROUBLESHOOTING

If the product does not function properly, please see the below for trouble shooting.

PROBLEM SOLUTION

My card is not read properly.

When I turn on the product, it sounds a
beep with dimly turned on indicator.

The read range (R/R) of the card differs
each time the product reads the card.

1) Check the rated voltage specifi ed in the user manual and the catalog.

2) Ensure that the card must comply with the PSK (125KHz) format provided by
Samsung.

- Cards of 13.56MHz format can not be used.

(Contact the card retailer regarding the card format.)

3) If the problem persists, contact the nearest customer service for your
assistance.

1) Ensure that you are using a larger-capacity adaptor than specifi ed in the user
manual or the catalog, which should cover the rated current consumption of the
reader. If you are using multiple readers that are connected to one adaptor,
make sure that the adaptor should be large enough to cover the current
consumption multiplied by the reader count.

Even with a large adaptor enough to supply adequate power, if the power cable is

2)
not a dedicated line (such as communication line or UPT cable), or if it’s so long to
cause power loss, you’d better replace it with a dedicated line or reinforce it.

3)

If the problem persists, contact the nearest customer service for your
assistance.

1) The characteristics of a card are determined by the nature of the coils used and in the
manufacturing process engaged by the card manufacturer. So what you do fi rst is to check
that the cards in use are made by the same manufacturer.
If you are using cards from different card makers, the read range (R/R) differs by
the card, which is the result of normal operation.

2)

If you encounter a different read range for each card that is made by the
same manufacturer, please contact the nearest customer service.

16_ troubleshooting

product specifi cations

PRODUCT SPECIFICATIONS

Item SSA-R2000V

Power / Current

Reading Time (Card)

Input Port

Output Port

LED Indicator

Beeper

Keypad

Operating Temperature

Operating Humidity

Color / Material

Dimension (W x H x D(mm))

Weight

DC 12V / Max.230mA

30ms

2 ea : External LED Control, External Buzzer Control

26bit Wiegand, 8bit Burst for PIN (Selectable)

3 LED Indicators (Red, Green and Orange)

Piezo Buzzer

12 Key Touch Keypad with Back Lighting

-30°C to +50°C

10% to 90% Relative Humidity Non-Condensing

Silver with Black/ Polycarbonate & Aluminum Die casting

87.0 x 109.0 x 25.0

350± 10g

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of
with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate
that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are
not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.

English _ 17

SALES NETWORK

SAMSUNG TECHWIN CO., LTD.

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : [phone]~60 FAX : [phone]

SAMSUNG TECHWIN AMERICA Inc.

1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : [phone] FAX : [phone]
www.samsungcctvusa.com

www.samsungsecurity.com
www.samsungtechwin.com

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : [phone] FAX : [phone]

P/No. : Z8100239101A