Hanwha Techwin SSA R1101V User Manual

Download

Page 1

RFID Reader

User Manual

SSA-R1001V SSA-R1101V

Page 2

RFID Reader

User Manual

Tra de mark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Warrant y

If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:

If the system behaves abnormally because you run a program irrelevant to the system operation.

• Deteriorated performance or natural worn-out in process of time

• Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)

•

is the registered logo of Samsung Techwin Co., Ltd.

Page 3

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

•

To reduce the risk of ﬁ re or electric shock, do not expose this appliance to rain or moisture.

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet. Using any other adapter could cause ﬁ re, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric shock, or damage to the product.

Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the controller, fasten it securely and ﬁ rmly. The fall of controller may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers ﬁ lled with water on top of the controller. Doing so may cause personal injury due to ﬁ re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modiﬁ cations or attempted repair.)

10.

. When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or electric shock.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -25°C), or high humidity. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause ﬁ re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the controller directly towards extremely bright objects such as sun.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English _ 3

SAFETY INFORMATION

Page 4

safety information

FCC Statement

Caution : Any changes or modiﬁ cations in construction of this device which are not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliﬁ ers) that

produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

10.

point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

11.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with

12.

the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

13.

combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any

14.

way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4_ safety information

Page 5

contents

PRODUCT INTRODUCTION

INSTALLATION AND EXTERNAL

CONNECTION

INITIALIZATION

OUTPUT FORMAT

TROUBLESHOOTING

6 Features 6 What’s included 7 At a Glance 8 Cable Color Scheme 8 Cable Selection

9 Installation 10 Precautions on installation 11 External Connection

12 Basic Operations

13 WIEGAND Output 14 RS-232 Output

15 Troubleshooting

CONTENTS

PRODUCT SPECIFICATIONS

16 Product Speciﬁ cations

English _ 5

Page 6

product introduction

FEATURES

This model is an elegant-looking proximity reader that can be easily attached to a metal doorframe or the wall. Featured by the epoxy adhesion and aluminium case, R1001V/R1101V is shock-resistant with a high level of weather-prooﬁ ng in any challenging weather conditions. The red and green indicators as well as the Piezo buzzer guarantee a stable and proper operation for you.

◆

13.56 MHz [MIFARE] Contactless Smart Card Reader

◆

Compatible with ISO14443 Type A

◆

3 Array LED Indicators (red and green) and Built-in Buzzer

◆

34 bit Wiegand / RS-232 Data Output

◆

Control of External LED Indicators

◆

Control of External Buzzer

◆

Epoxy adhesion and aluminium case

◆

Reverse Polarity Protection

◆

Weatherproof and Dustproof

WHAT’S INCLUDED

Check if the following items are included in the product package.

What’s included in SSA-R1001V

RFID Reader

SSA-R1001V

user manual

SSA-R1101V

SSA-R1001V

Bezel

READER Module

3mm Hex

Wrench (x1)

What’s included in SSA-R1101V

SSA-R1101V

Bezel

READER Module

6_ product introduction

3mm Hex

Wrench (x1)

3.5x40mm screws (x2)

3.5x25mm screws (x2)

6x30mm Plastic Anchor (x2)

3.5x40mm screws (x2)

3.5x25mm screws (x2)

6x30mm Plastic Anchor (x2)

Quick Guide CD Manual

RFID Reader

SSA-R1001V

user manual

SSA-R1101V

Quick Guide CD Manual

Page 7

AT A GLANCE

Front/Rear

PRODUCT INTRODUCTION

LED

Buzzer

Connection Cable

Fixing Hole

Tamper Switch

Displays the system operation status using red and green indicators.

Piezo buzzer.

Used to connect to the power or I/O cable.

Fixing hole for wall-mounting.

A tamper switch to detect falling from the wall.

English _ 7

Page 8

product introduction

Cable Type

Belden #9409, 18 AWG 2 Conductor, Unshielded

CABLE COLOR SCHEME

Item Cable Color Signal Line Description

Power

Input

Output

Communication

Tamper

Light yellow

Not used

CABLE SELECTION

Item

Red DC +12V DC +12V supplied

Black GND Earth-grounding for power

Blue Buzzer Control BUZZER Control Input Port

Yellow LED Control LED Control Input Port

Green Out Wiegand 0

White Out Wiegand 1

Purple RS-232(TX)

Pink

Gray

Brown

Orange

Tamper Output (COM)

Tamper Output (NC)

Wiegand Data 0 Output Port

Wiegand Data 1 Output Port

RS-232 Transmission Output

Port

Tamper Output Port

Not Connected

Cable Type

Power (DC12V)

WIEGAND Output Buzzer Control

LED Control Tamper Output

RS-232 Cable

8_ product introduction

Belden #9409, 18 AWG 2 Conductor, Unshielded

Belden #9512, 22 AWG 4 Conductor, Shielded

Belden #9514, 22 AWG 8 Conductor, Shielded

Belden #9829, 24 AWG 2-twisted pair, Shielded

Page 9

installation and external connection

INSTALLATION

- Inserted in the doorframe / attached to the wall

Two 6-32 or M3 holes are 3.3” (8.38 cm) away from each other vertically; between the two exists one 1/2” hole

1. through which the reader cables are arranged. The midway hole is located 1.7” (4.31cm) down from the upper hole. (If the product is already installed, you can skip the follow step)

Insert the reader cables to the midway hole and ﬁ x the reader module with two 6-32 or M3 screws.

Insert the reader module into the appearance case and tighten the screw (M6x8mm) using the hex wrench.

Upper

6-32 hole

1.7”

(4.31cm)

3.3”

(8.38cm)

6-32 or M3 Screws

1/2”hole

6-32 or M3 Screws

INSTALLATION AND EXTERNAL CONNECTION

6-32 hole

Lower

Gang Box

Reader

Module

Bezel

3mm Hex Wrench 3mm Hex Wrench

Wall Mount

Mullion Mount

Reader Module

Electric Gang Box Mount

Bezel

English _ 9

Page 10

installation and external connection

PRECAUTIONS ON INSTALLATION

If installing on a metal wall

If you install the reader on a metal wall, the read range may be reduced.

To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below.

Metal

Wall

Spacer

Reader

If installing more than one reader side by side or front and back

If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning two readers read the same card simultaneously.

To avoid this problem, keep at least 20 cm of space between the two readers.

Minimum

20cm

#Reader 2

#Reader 1

10_ installation and external connection

#Reader 1

Minimum

#Reader 2

20cm

Page 11

EXTERNAL CONNECTION

Wiring Diagram

CONTROLLER

Item

Power Supply Unit

Wiegand Connection

LED Control

Buzzer Control

RS-232 Connection

Tamper Connection

SSA-R1001V/SSA-R1101V

Buzzer Control In

LED Control In

Wiegand Data 0 Out

Wiegand Data 1 Out

Tamper Output(COM)

Tamper Output(NC)

Blue

Yellow

Green

White

Pink

Light yellow

Red Black

DC +12V

POWER

RS-232(TX)

RS-232(GND)

GND

Brown

Black

Cable Wiring

Connect the DC+12V to the red line.

Connect GND to the black line.

Connect the green line of the product to the Wiegand D0 input port of the controller.

Connect the white line of the product to the Wiegand D1 input port of the controller.

To control the LED indicators, connect the yellow line to the output port (relay) of the controller.

To control the built-in buzzer, connect the blue line to the output port (relay) of the controller.

Connect to the COM port of the PC. (Connect pin 2 of the DB-9 connector to the purple line; connect the black line of the device (GND) to pin 5 of the DB-9 connector)

Connect the pink line of the product to the GND terminal of the controller.

Connect the light yellow wire of the product to the GND terminal of the controller.

INSTALLATION AND EXTERNAL CONNECTION

English _ 11

Page 12

initialization

BASIC OPERATIONS

Initial State (when the power is supplied)

When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turn on .

Using the card

Present the card to the reader until you hear a beep and the red indicator turns green. When the reader has transferred the data to the controller, it returns to Standby with the

red indicator turned on and waits for reading the next card.

Card

[

l zj

i

]

z j

z zh T zY W W W

LED Control

You can control the LED indicator of the device at your preference.

Connect the LED control input line (yellow) to the NO port of the controller relay output, and GND to the COM port. Set the I/O of the controller so that you can change the color of the LED indicators. While the LED control is

working, the green indicator stays solid. This function not only enables you to change the color representing Standby from red to green, but it can be also

applied to make various modiﬁ cations according to the different I/O settings of the controller. For more information about the I/O settings of the controller, refer to the user manual of the controller.

Buzzer Control

You can control the buzzer of the device at your preference.

You can conﬁ gure the I/O settings of the controller so that it sounds a beep. While the buzzer control is working, the product keeps sounding the beep.

The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication.

Furthermore, you can make various modiﬁ cations according to the different I/O settings of the controller.

For more information about the I/O settings of the controller, refer to the user manual of the controller.

Card reading is not available while the buzzer control is sounding the buzzer.



12_ initialization

Page 13

output format

WIEGAND OUTPUT

Timing Diagram

100us

DATA-0

DATA-1

1ms

123 0LOGIC 1 1 1 0 0

Data Type

Bit 1 : Even Parity (bit2~bit17)

•

Bit2~Bit33 : 4 byte ID number

•

Bit34 : Odd Parity (bit18~bit33)

•

OUTPUT FORMAT

0V 5V

n-2 n-1 n *n : 34

English _ 13

Page 14

output format

RS-232 OUTPUT

Output Waveform

MSB

2 Stop Bits

Space(=0)

Mark(=1)

+15V

+3V

-3V

-15V

LSB

01 100000 0

8 Data Bits

Start Bit

Data packet corresponding to ASCII character ‘A’

Data Type

Start (0X02H) Data (10 Char) End (0x03H) LRC

START(0X02H) DATA (10 Char) END (0x03H) LRC

Check the following settings:



Baud Rate : 9600bps DataBit : 8 Parity : None Stop Bit : 1



LRC: This is the result of XOR operation of each byte from Start to End.

Indeterminate

Region

14_ output format

Page 15

troubleshooting

TROUBLESHOOTING

If the product does not function properly, please see the below for trouble shooting.

PROBLEM SOLUTION

My card is not read properly.

When I turn on the product, it sounds a beep with dimly turned on indicator.

The read range (R/R) of the card differs each time the product reads the card.

1) Check the rated voltage speciﬁ ed in the user manual and the catalog.

2) Ensure that you are using an ISO14443 Type A card. Cards of 125 kHz format can not be used. 13.56 MHz cards of Type B, ISO15693 format

- can not be used. (Contact the card retailer regarding the card format.)

3) If the problem persists, contact the nearest customer service for your

assistance.

Ensure that you are using a larger-capacity adaptor than speciﬁ ed in the user manual or the

catalog, which should cover the rated current consumption of the reader. If you are using multiple readers that are connected to one adaptor, make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count.

Even with a large adaptor enough to supply adequate power, if the power cable is not a dedicated line (such as communication line or UPT cable), or if it’s so long to cause power loss, you’d better replace it with a dedicated line or reinforce it.

3) If the problem persists, contact the nearest customer service for your

assistance.

The characteristics of a card are determined by the nature of the coils used and in the

manufacturing process engaged by the card manufacturer. So what you do ﬁ rst is to check that the cards in use are made by the same manufacturer. If you are using cards from different card makers, the read range (R/R) differs by the card, which is the result of normal operation.

2) If you encounter a different read range (R/R) for each card that is made by

the same manufacturer, please contact the nearest customer service.

TROUBLE SHOOTING

English _ 15

Page 16

product speciﬁ cations

PRODUCT SPECIFICATIONS

Item SSA-R1001V SSA-R1101V

Power / Current

Reading Time (Card)

Input Port

Output Port

LED Indicator

Beeper

Operating Temperature

Operating Humidity

Color / Material

Dimension (W x H x D(mm))

Weight

DC 12V / Max.80mA

30ms

2ea : External LED Control, External Buzzer Control

34bit Wiegand

2 Color LED (Red and Green)

Piezo Buzzer

-25°C to +50°C

10% to 90% Relative Humidity Non-Condensing

Silver with Black/Polycarbonate & Aluminum Die casting

47.0 x 120 .0 x 26.0 75.0 x 120.0 x 26.0

250g ±10 340g ±10

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

16_ product speciﬁ cations

Page 17

SALES NETWORK

SAMSUNG TECHWIN CO., LTD.

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745

SAMSUNG TECHWIN AMERICA Inc.

1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com

www.samsungsecurity.com www.samsungtechwin.com

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS TEL : +44-1932-45-5300 FAX : +44-1932-45-5325

P/No. : Z8100239401A