Hanwha Techwin SNHV6435DN User Manual

SMARTCAM D1

User Manual

SNH-V6435DN

Smartcam D1

User Manual

Copyright

Hanwha Techwin

©2017

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this
manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced,
distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

document, but no formal guarantee shall be provided. Use of this document and the subsequent results
shall be entirely on the user’s own responsibility.
contents of this document without prior notice.

Co., Ltd. All righ ts reserve d.

makes the best to verify the integrity and correctness of the contents in this

Hanwha Techwin

reserves the right to change the

SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from
which the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.

Industry Canada Statement

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20 cm between the radiator & your body.

Instructions & Warranty

The manufacturer is not responsible for any loss or radio/TV interference caused by
unauthorized modification of the product.

Such modification will void the warranty of the product as well as the user’s right of use.

WARNING

• The product must be assembled and installed by an adult.

• Before using, read all instructions on this manual thoroughly and follow operational

instructions, warnings on this manual and printed on the product.

• To avoid entangled power cord, do not place it around the baby bed or other infant
furniture. Keep this product and its power cord out of children’s reach.

• Especially, the power cord should be installed carefully while keeping it out of children’s
reach.

• Never use the product near bath tub, sink, washing machine and in wet basement to
avoid moisture.

• The product is not designed for medical monitoring, and requires a grown-up’s
protective supervision on its use.

• To avoid overheating of the product, do not expose the product to direct sunlight; do not
install or use near a heat source such as heater, radiator, cooking devices (ex: electric
stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).

• Make sure to keep ventilated while using the product.
Avoid pillar or furniture that may block ventilation, when installing the product.

• Make sure to use the power adaptor provided. If used with unidentified adaptor, it may
damage the product. The power adaptor must be used with regular household electric
supply.

• Avoid sharp, pointed objects around the adaptor’s cable, not to damage the cable.

• Be warned and never hold the cable’s stripped part when connecting / disconnecting

the adaptor to/from the wall outlet.

• To avoid entangled cable lines, avoid using cable extension for adaptor’s power cord.

• The product’s servicing is allowed only to authorized Hanwha Techwin service

personnel.

• Accessories and small parts of the product should be stored keeping out of children’s
reach.

• The product is not designed to replace responsibility of human supervision on children.

• The product is not equipped with device of immediate notification to adult with

accidental/sudden children‘s move; it requires periodic checks and human supervision.

• This appliance and its antenna must not be collocated or operation in conjunction with
any other antenna or transmitter. A minimum separation distance of 20 cm must be
maintained between the antenna and the person for this appliance to satisfy the RF
exposure requirements.

Contents

GETTING STARTED

Features ……………………………………………………… 5

What’s Included ……………………………………………… 6

Part names and functions …………………………………… 7

INSTALLATION & NETWORK CONNECTION

Installation …………………………………………………… 9

Network Connection and Settings …………………………… 13

APPENDIX

Specifications ………………………………………………… 15

Troubleshooting ……………………………………………… 19

GettinG Started

Features 5

What’s Included 6

Part names and functions 7

Front 7
Rear 7
Side 8
Components 8

01

Features

• Easy to install

- The Wi-Fi Direct button allows easy connection to a wireless router.

• Remote monitoring

- You can monitor your SmartCam D1 remotely, at any time and from any location,
using your smartphone.

• Real-time alarm

- When the bell rings, a push alarm is sent to the smartphone.

• Face recognition

- You can set the person who wants to receive the alarm.

• Downloading a recorded video

- You can download motion detection/audio detection/manually recorded video to
the user's smartphone (Android).

01

Getting Started

5

What’s Included

Check for components when opening the product package.

SmartCam D1 Quick Start Guide (Option by region) Warranty Card GPL Lisence

Face cover Secure screw Plastic anchor Drill bit

Screw driver Power stabilizer Power stabilizer Cable Power cable

6

· English

Connector

Part names and functions

Front Rear

01

This is a case mounted on the exterior of

Deco Case

the SmartCam D1

Microphone hole

Status LED

Bell Button

Power Input

This is the AC adapter connection
terminal.

Getting Started

7

Speaker hole

ComponentsSide

WiFi Direct Button

Wi-Fi is used for wireless communication

RESET

between product and smartphone.

Reset button

Resets the product settings to the factory
default. The system restarts if you press the
button for 10 seconds using a pointed
object such as a needle.

` If you press too strongly, the button

J

can break.

8

· English