Hanna Instruments HI 983310 User Manual

SPECIFICATIONS

Instruction Manual

Range 0 to 1999 ppm

0.0 to 60.0 °C

Resolution 1 ppm

0.1°C

Accuracy ± 2% f.s.

± 0.5°C

Typical EMC ± 2% f.s.
Deviation ± 0.5°C

TDS Factor 0.5

Calibration Factory-calibrated

Temperature Automatic from 0 to 60°C
Compensation β=2%/°C, Tref.=25°C

Battery Type 2 x 1.5V AAA Alkaline

Environment 0 to 50°C; 100% RH

Dimensions 92 x 38 x 450 mm (3.6x1.5x17.7")

Warranty

All Hanna Instruments meters are warranted for two years against defects in workman­ship and materials when used for their intended purpose and maintained according to
instructions. This warranty is limited to repair or replacement free of charge.
Damages due to accident, misuse, tampering or lack of prescribed maintenance are not
covered.
If service is required, contact the dealer from whom you purchased the instrument. If
under warranty, report the model number, date of purchase, serial number and the
nature of the failure. If the repair is not covered by the warranty, you will be notified of
the charges incurred. If the instrument is to be returned to Hanna Instruments, first
obtain a Returned Goods Authorization number from the Customer Service department
and then send it with shipping costs prepaid. When shipping any instrument, make sure
it is properly packaged for complete protection.
To validate your warranty, fill out and return the enclosed warranty card within 14 days
from the date of purchase.

Recommendations for Users

Before using this product, make sure that it is entirely suitable for the environment in
which it is used. Operation of this instrument in residential areas could cause interfer­ence to radio and TV equipment. Any variation introduced by the user to the supplied
equipment may degrade the instrument EMC performance. To avoid electrical shocks,
do not use this instrument when voltage at the measurement surface exceeds 24 VAC or
60 VDC. To avoid damage or burns, do not perform any measurement in microwave
ovens.

ISTAQUADIPR1 03/2001

Manufacturers since 1978

AquaDip

Rugged Waterproof

TDS / °C meter

This Instrument is in

Compliance with the CE Directives

Dear Customer,
Thank you for choosing a Hanna product.
Please read this instruction manual carefully before using the in-

strument.
This manual will provide you with the necessary information for a

correct use of the instrument, as well as a precise idea of its
versatility.

If you need additional technical information, do not hesitate to
e-mail us at [e-mail].

These instruments are in compliance with directives.

TAKING MEASUREMENTS

The meter is factory calibrated for ppm and temeprature.

Press the ON/OFF key to turn
the meter on.

Immerse the probe into the so­lution to be tested. The
minimum water level must be
approx. of 4½ cm, while the
maximum level has not to ex­ceed the indicated hole. If
possible, tap the probe to re­move any air bubbles that may
be trapped inside.

Allow for the reading to stabi­lize. The LCD displays the
ppm reading.

Press the RANGE key to view
the temperature reading.

Press RANGE again to return
to ppm reading.

If the ppm reading is out of range, the “
is displayed. If the temperature reading is out of range,
the “°C” symbol blinks.

---

” indication

HOLD FUNCTION

To freeze the current measure­ment on the LCD, press and
hold the RANGE/HOLD key for
about 3 seconds.

When the hold function is active, the LCD displays
alternatively the “HLd” indication and the frozen read­ing.

Press RANGE to switch from ppm to temperature read­ing.

Press the ON/OFF key to exit the hold mode and
return to normal operation.

BATTERY REPLACEMENT

To prolong the battery life, the meter switches itself off
after 5 minutes of non-use.

Variations in readings or fading display can indicate
weak batteries.

If the batteries are too weak to support proper opera­tions, the LCD displays the message “Eb” and then the
meter switches itself off.

Battery replacement must only take place in a non­hazardous area using AAA-type 1.5V, alkaline batteries.

In order to replace run down
batteries, simply remove the
two screws on the bottom
cover and replace the two 1.5V
AAA batteries with new ones,
paying attention to the correct
polarity.

New batteries allow approx. 1000 hours of continuous
use (with 1175mA/h batteries).