Hanna Instruments HI 982411-0 User Manual

Instruction Manual

HI 982411-0 HI 982411-1

Panel-Mounted

ORP Indicators &

Controllers

Manufactors since 1978

These Instruments are in

Compliance with the CE Directives

Dear Customer, Thank you for choosing a Hanna product. This manual will

provide you with the necessary information for the correct operation of the meter. Please read it carefully before using the meter. If you need additional technical information, do not hesitate to e-mail us at tech@hannainst.com.

These instruments are in compliance with the directives.

PRELIMINARY EXAMINATION

Remove the instrument from the packing material and examine it carefully. If any damage has occurred during shipment, immediately notify your Dealer or the nearest Hanna Customer Service Center.

The meter is supplied with:

- Mounting bracket;

- Instruction manual. Note: Conserve all packing material until the instrument

has been observed to function correctly. Any defective item must be returned in its original packing.

SPECIFICATIONS

HI 982411

Range 0 to 1000 mV Resolution 1 mV Accuracy (@ 20°C/68°F) ±5 mV Calibration Manual, at one point (OFFSET)

through trimmer

Setpoint Adjustable, from 0 to 1000 mV Dosing Contact Open when Measure > Setpoint

Close when Measure < Setpoint

Power supply: External HI 982411-0 12 VDC HI 982411-1 115/230 VAC; 50/60Hz Dimensions 79 x 49 x 95 mm (3.1 x 1.9 x 3.7”)

Weight: HI 982411-0 140 g (4.96 oz) HI 982411-1 250 g (8.85 oz)

CE DECLARATION

OF CONFORMITY

HI982411-0 and HI982411-1

14-4-99

WARRANTY

HI 982411-0 and HI 982411-1 are warranted for two years against defects in workmanship and materials when used for their intended purpose and maintained according to instructions.

This warranty is limited to repair or replacement free of charge. Damages due to accident, misuse, tampering or lack of prescribed

maintenance are not covered. If service is required, contact the dealer from whom you purchased

the instrument. If under warranty, report the model number, date of purchase, serial number and the nature of the failure. If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization Number from the Customer Service department and then send it with shipment costs prepaid. When shipping any instrument, make sure it is properly packaged for complete protection.

To validate your warranty, fill out and return the enclosed warranty card within 14 days from the date of purchase.

All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner, Hanna Instruments Inc., Woonsocket, Rhode Island, 02895 , USA.

GENERAL DESCRIPTION

HI 982411-0 and HI 982411-1 are ORP indicators and controllers with a relay output designed for simplicity of use in a wide range of industrial applications.

The models are panel-mounted with membrane keypads on the front panel and an easy-to-read LCD display.

Power supply, wiring and selection are made via the plugin terminal blocks on the rear panel. The instruments are equipped with a BNC socket and accept input from ORP electrode.

LED indicators on the front panel identify whether the controller is in set or reading mode, and if dosing device is activated.

Recommendations for Users Before using this product, make sure that it is entirely suitable for the environment in which it is used. Operation of this instrument in residential areas could cause unacceptable interferences to radio and TV equipment. The glass bulb at the end of the electrode is sensitive to electrostatic discharges. Avoid touching this glass bulb at all times. During operation, ESD wrist straps should be worn to avoid possible damage to the electrode by electrostatic discharges. Any variation introduced by the user to the supplied equipment may degrade the instrument’s EMC performance. To avoid electrical shock, do not use this instrument when voltage at the measurement surface exceeds 24 VAC or 60 VDC. To avoid damage or burns, do not perform any measurement in microwave ovens.

ISTR982411R4 06/2001

Hanna Instruments reserves the right to modify the design, construction and appearance of its products without advance notice.

HI 982411

ORP CONTROLLER

OPERATIONAL GUIDE

95mm MIN

3.74"

76mm

0.25/4mm

0.01/0.160"

79mm

3.11"

ADJUSTABLE LOCATION BRACKET

POWER CONNECTION HI 982411-0

Connect a 2-wire power cable to the terminal strip while paying attention to the correct positive and negative contacts (12 VDC).

HI 982411-1

Connect a 3-wire power cable to the terminal strip while paying attention to the correct earth, neutral and line contacts (115/230 VAC).

Notes:

• All external cables connected to the rear panel should end with wire lugs.

• It is recommended to cover the unused terminals with insulating tape.

• At start up the meter needs a few seconds to stabilize. Wait until a stable reading is displayed.

DOSING CONTACT

This contact (maximum 5A, 240VAC, 30VDC) is used for connection to an alarm or dosing system. The relay contact acts as a power switch for the controlling device.

OPERATING THE METER

All operations are controlled via the front panel keys and trimmers. “SET” and “MEAS” LEDs light up to indicate which is the operating function.

Make sure that the meter is calibrated and that the Setpoint is properly adjusted before proceeding.

Attach the electrode to the meter with a BNC connector. Install the electrode in the fittings or immerse it in the solution to be monitored. Press the "MEAS" key.

The LCD will show the ORP value in mV unit. Any initial variation on readings may be due to tempera-

ture compensation. The “DOSING” LED will light up when the dosing contact is

closed.

CALIBRATION

This meter is factory calibrated. The calibration can be performed by diving the electrode in HI7020S solution and adjusting the calibration trimmer.

SETPOINT

Press the "SET" key. The display will show the default or previously adjusted value. Using a small screwdriver adjust the "SET" trimmer until the required value is displayed.

FUNCTIONAL DESCRIPTION

FRONT PANEL

Keypad

SET To display

setpoint

MEAS To display

measurement

Trimmers

CAL For mV

Calibration

SET To adjust

setpoint

LEDs

SET ON when LCD

displays the set value

MEAS ON when LCD displays the measured value. DOSING ON when dosing contact is activated (closed)

REAR PANEL

1. Power Supply:

HI 982411-0 HI 982411-1

12 VDC 115/230 VAC

L1: Positive 230 VAC L2: Negative 115 VAC L3: ------ Neautral L4: ------ Potential Earth Note: the power input is internally protected by a 400 mA fuse

2. Alarm contact: This dosing contact acts as a switch. The alarm (dosing) contact will be closed when measure is lower than setpoint.

3. BNC socket for ORP electrode.

HI 982411

ORP CONTROLLER

0 ...1000 mV

DOSING

CAL

SET MEAS

SET

HI982411 LAYOUT

Front view of the panel-mounted unit

Side view of the panel-mounted unit

Supplied adjustable location brackets allow the controller to slide into the cut-out and will hold the unit securely in place. 95 mm (3.74") is the minimum amount of space required to install the controller.

Panel-mounted unit assembling view

42mm

1.65"

49mm

1.93"

73mm

2.87"

HI 740146

ACCESSORIES

ORP SOLUTIONS HI 7020M 200-275mV Solution, 230mL bottle HI 7020L 200-275mV Solution, 460mL bottle HI 7091M Pre-Treatment Reducing Solution, 230mL HI 7091L Pre-Treatment Reducing Solution, 460mL HI 7092M Pretreatment Oxidizing Solution, 230mL HI 7092L Pre-Treatment Oxidizing Solution,460mL ELECTRODE STORAGE SOLUTIONS HI70300M Storage Solution, 230mL bottle HI 70300L Storage Solution, 460mL bottle

79mm

3.11"

ELECTRODE CLEANING SOLUTIONS HI 7061M General Cleaning Solution, 230mL bottle HI 7061L General Cleaning Solution, 460mL bottle

ORP ELECTRODES HI3214P/2 BNC-type, platinum, double-junction, plas-

tic-body with 2m (6.6’) cable

HI2003/5 Heavy-duty, BNC-type, platinum, double junc-

tion, plastic-body with 5m (16.5’) cable

HI2012/5 Heavy-duty, BNC-type, platinum, double junc-

tion, plastic-body with 5m (16.5’) cable

EXTENSION CABLES FOR SCREW-TYPE ELECTRODES ONLY (SCREW TO BNC CONNECTOR) HI7855/1 Extension cable 1m (3.3') long HI7855/3 Extension cable 3m (9.9') long HI7855/5 Extension cable 5m (16.5') long HI7855/10 Extension cable 10m (33') long HI7855/15 Extension cable 15m (49.5') long

OTHER ACCESSORIES BL -PUMPS Dosing Pumps with Flow Rate from 1.5 to

20 LPH

HI 6050 and HI 6051 Submersible Electrode Holders HI 6054 and HI 6057 Electrode Holders for In-Line Applications HI 710005 12 VDC power adapter, US plug

HI 710006 12 VDC power adapter, European plug HI 710012 12 VDC power adapter, Australian plug HI 710013 12 VDC power adapter, Southern Africa plug HI 710014 12 VDC power adapter, UK plug

HI 731326 Calibration Screwdriver (20 pcs) HI 7871 & HI 7873 Level Controllers