HAMPTON BAY Home Depot SKU 987-324 Instruction Manual

INSTRUCTION MANUAL

LIGHT FIXTURE

Brushed Steel Finish

Home Depot SKU 987-324(UPC008938233729)

1

Thank you for purchasing this Hampton Bay interior light fixture. This product has
been manufactured with the highest standards of safety and quality.

FEATURES:

1. Fixture heads are multi-directional.

2. Glass shade is moiety cleared and moiety frosted made it good-looking.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our Customer Service Team at 1-877­527-0313 or visit www.homedepot.com. Please reference SKU 987-324, UPC 008938233729.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: Make sure power is turned off at the electrical panel box before

beginning your installation. Turning the power off at the wall switch is not sufficient
to prevent electrical shock.

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO
PERSONS

1. Read all instructions prior to beginning the installation process.

2. Do not install this lighting system in a wet location.

3. Lighted lamp is HOT!

4. CAUTION - HOT SURFACE. Keep away from curtains and other combustible

materials.

5. Do not touch bulb, lens, guard or enclosure at any time. Use a soft cloth. Oil from

skin may damage lamp.

6. CAUTION-To reduce the risk of fire, use only 50W Max type GU10 shielded

bulbs.

7. All electrical connections must be in accordance with local codes and the

National Electrical Code. If you are unfamiliar with methods of installing
electrical wiring, secure the services of a qualified licensed electrician.

8. These fixtures are intended to be mounted to a 4"square x 2-1/8"deep metal

octagon outlet box. The box must be directly supported by the building structure.

9. Before starting the installation, disconnect the power by turning off the circuit

breaker or by removing the appropriate fuse at the fuse box. Turning the power
off using the light switch is not sufficient to prevent electrical shock.

SAVE THESE INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included):

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

x 3 GU10 Halogen x1 Re-lamping tool (E) x1 Hardware Packet (F)
50 Watt Bulb(s) (D)

Ladde

r

Safety Gloves Flathead Phillips Electrical Wire

Goggles Screwdrive

r

ScrewdriverT ape Cutters

2

ASSEMBLY INSTRUCTIONS (AS SHOWN IN DIAGRAM):

1. Make sure the main power to the circuit is OFF.

2. Install mounting bracket to existing outlet box with screws(A).

3. Pull wires through mounting bracket hole.

4. ELECTRICAL CONNECTIONS (B):

a. Conn ect the white wire(s) from the fixture to the white wire of the supply

circuit.

b. Connect the black wire(s) from the fixture to the black wire of the supply

circuit.

c. Conn ect the green colored (or bare copper) wire to the grounding co nductor

of the supply circuit.

d. Use U.L. Listed wire connectors suitable for the size, type and number of

conductors. No loose strands or loose wires should be present.

e. Secure wire connectors with U.L. Listed electrical tape.
f. Carefully tuck connected wires back into the outlet box.

5. Secure the canopy by threading the nut onto the mounting bracket stem. Place the

decorative nut onto the end of the mounting bracket stem(C) (Adjust the length of
the stem when necessary).

RELAMPING THE BULB (D)

1. Make sure that the power is turned off.

2. THE BULB IS HOT! Make sure that the bulb is cool before re-lamping the

fixture.

3. Remove and replace the bulb using the re-lamping tool(E).

4. Restore electrical power.

CAUTION: Do not exceed the recommended maximum fixture wattage.

ASSEMBLY DIAGRAM

3

TROUBLE SHOOTING:

PRODUCT MAINTENANCE:

1. Turn off power to the light fixture.
2 To clean simply wipe with a soft dry cloth.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives.

4. Allow the fixture to dry completely before power is restored.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials
and workmanship for a period of five (5) years from date of purchase. This warranty
applies only to the original consumer purchaser and only to products used in normal
use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at
the manufacturer’s discretion, provided that the product has not been damaged
through misuse, abuse, accident, modifications, alterations, neglect or mishandling.
This warranty shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions supplied
with the product. This warranty shall not apply to a failure of the product as a result of
an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other
failure not relating to faulty material or workmanship. This warranty shall not apply to
the finish on any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear. The manufacturer does not warrant and specially
disclaims any warranty, whether express or implied, of fitness for a particular purpose,
other than the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or damage,
including but not limited to any labor/expense costs involved in the replacement or
repair of said product.

Problem Possible Cause Corrective Action

1. Light bulb is burned out. 1. Replace light bulb.

2. Power is off. 2. Make sure power supply is on.

3. Faulty wire connection. 3. Check wiring.

Light Bulb will not
illuminate.

4. Faulty switch. 4. Test or replace switch.
Fuse blows or circuit breaker
trips when light bulb is
illuminated.

Crossed wires or power wire
is grounding out.

Check wire connections.

4