HAMPTON BAY Home Depot SKU 401-718 Instruction Manual

INSTRUCTION MANUAL

2LT Interior Flushmount

The Home Depot SKU 401-718 (UPC 6940500310534)

Page 1

Thank you for purchasing this Hampton Bay interior flushmount. This
product has been manufactured with the highest standards of safety and
quality.

FEATURES:

1. Two-light interior flushmount in tuscan bronze finish with antique scavo
glass.

2. This fixture has been engineered to safely use two 60 watt medium base
incandescent light bulbs (do not exceed 60 watts each) (not included).

3. For energy savings, this fixture has been engineered to safely use two
standard base compact fluorescent light bulbs (for equivalent light output,
do not exceed 15 watts each) (not included).

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local The Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU 401-718 or UPC 6940500310534.

Page 2

CAUTION:

1. Before starting installation of this fixture or removal of a previous fixture,

disconnect the power by turning off the circuit breaker or by removing the
fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS.

3. If you have any non-electrical questions about this fixture, please contact

our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU 401-718 or UPC

6940500310534.

4. Keep your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):

2 Light Bulbs Safety Goggles Ladder Gloves Wire Strippers
(60 watt maximum)
(or CFL equivalent)

Flathead Screwdriver Phillips Screwdriver Electrical Tape Wire Cutters

Page 3

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

1ea Hex Nut (#5) 1ea Nipple (#6) 1ea Shade (#7)

1ea Washer (#8) 1ea Bottom Cover (#9) 1ea Finial (#10)

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Unscrew the Finial (#10) from the Nipple (#6). Screw the Nipple (#6) into

the Bushing (#2). Tighten the Hex Nut (#5) against the Bushing (#2) to

secure the Nipple (#6).

3. Before continuing Assembly, please proceed to the Installation Instructions.

4. Install two 60 watt medium base incandescent light Bulbs (#4) (not

included) or two equivalent standard base compact fluorescent light bulbs

(not included) in the two Sockets (#3) in the fixture.

5. Place the Shade (#7) over the Nipple (#6). Screw the Washer (#8) onto the

Nipple (#6). Place the Bottom Cover (#9) over the Nipple (#6). Screw the

Finial (#10) onto the Nipple (#6) to secure the Shade (#7) and the Bottom

Cover (#9).

Page 4

ASSEMBLY:

Page 5

PARTS INCLUDED FOR INSTALLATION (parts are not to scale):

3ea Wire Connectors (#12) 2ea Outlet Box Screws (#13) 1ea Mounting Strap (#14)

1ea Ground Screw (#15) 2ea Mounting Screws (#16)

INSTALLATION INSTRUCTIONS:

1. Screw the two Mounting Screws (#16) into the Mounting Strap (#14). Mount the

Mounting Strap (#14) to the Outlet Box (#11) using the two Outlet Box Screws (#13).
[Make sure the heads of the Mounting Screws (#16) are facing outside when the
Mounting Strap (#14) is attached to the Outlet Box (#11).]

2. Wrap the ground wire from the fixture around the Ground Screw (#15) on the

Strap

(#14), and then connect the ground wire from the fixture to the ground wire from

Mounting

the Outlet Box (#11). Connect the white wire from the fixture to the white wire (neutral
wire) from the Outlet Box (#11). Connect the black wire from the fixture to the black
wire (live wire) from the Outlet Box (#11). Cover the three connections using the three
Wire Connectors (#12). Wrap the three wire connections with electrical tape for a more
secure connection. Position the wires back inside the Outlet Box (#11). Note: If you have
electrical questions, consult your local electrical code for approved grounding methods.

3. Place the Canopy (#1) over the Outlet Box (#11). Allow the heads of the Mounting

Screws (#16) to come out through the large ends of the keyholes on the Canopy (#1).
Twist the Canopy (#1)

narrow ends of the keyholes. Tighten the Mounting Screws (#16) to secure the

the

clockwise

until the heads of the Mounting Screws (#16) slide into

Canopy (#1).

4. Before completing Installation, please return to Assembly Instruction #4.

5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the

light switch on to activate the fixture.

Page 6

INSTALLATION:

Page 7

TROUBLESHOOTING:

Problem Possible Cause Corrective Action

Light bulb will not
illuminate.

1. Light bulb is burned out. 1. Replace light bulb.

2. Power is off. 2. Make sure power supply
is on.

3. Faulty wire connection. 3. Check wiring.

4. Faulty switch. 4. Test or replace switch.

Fuse blows or circuit breaker
trips when light bulb is

Crossed wires or power wire
is grounding out.

Check wire connections.

illuminated.

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the glass and surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and
interior surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of
five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation,
and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that
the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any
way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not
relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant

and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be
liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs
involved in the replacement or repair of said product.

Page 8