Hamilton Beach 76250, 76350 Use And Care Manual
Customer Service Number
In USA: 1-800-851-8900 • In Canada: 1-800-267-2826
Web Site Address – http://www.hambeach.com
Keep these numbers for future reference!
Use & Care for Penguin™ Can Openers
Utilisation et entretien des ouvre-boîtes Penguin™
Numéro d’assistance aux clients
Aux États-Unis : 1-800-851-8900 • Au Canada : 1-800-267-2826
Conservez ces numéros, ils peuvent vous être utiles!
32
When using electrical appliances, basic safety precautions should
always be followed, including the following:
1. Read all instructions.
2. To protect against risk of electrical shock, do not put can opener
body, cord, or plug in water or other liquid.
3. Close supervision is necessary when any appliance is used by
or near children.
4. Unplug from outlet when not in use, before putting on or taking
off parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug,
or after the appliance malfunctions or is dropped or damaged
in any manner. Call our toll-free customer service number for
information on examination, repair, or electrical or mechanical
adjustment.
7. The use of attachments not recommended or sold by Hamilton
Beach/Proctor-Silex, Inc. may cause fire, electric shock, or injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
10. Do not open pressurized (aerosol-type) cans.
11. Do not open cans of flammable liquids such as lighter fluid.
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
CONSUMER SAFETY INFORMATION
This appliance is intended for household use only.
This appliance is equipped with a polarized plug. This type of plug
has one blade wider than the other. The plug will fit into an electrical
outlet only one way. This is a safety feature. If you are unable to
insert the plug into the outlet, try reversing the plug. If the plug
should still fail to fit, contact an electrician to replace the obsolete
outlet. Do not attempt to defeat the safety purpose of the polarized
plug.
KNOW YOUR CAN OPENER
Flip up the magnet to easily check correct can position.
Cutting assembly with
removable
flip-up magnet
Cutting assembly
release button
Figure 2
Figure 1
54
HOW TO CLEAN YOUR CAN OPENER
HOW TO USE YOUR CAN OPENER
1. Place can opener on level surface.
2. Plug cord into electrical outlet.
3. For first time use, push front of cutting
assembly to lift blade. See Figure 3.
4. Make sure that flip-up magnet is in the
up position. Tilt top of can in, to position
cutting blade inside rim of can.
5. Push down top of cutting assembly.
6. The motor will begin turning can and
cutting lid. (It is not necessary to hold
the cutting assembly down or to hold
the can during the cutting action, unless
opening large or heavy cans.)
7. The motor will automatically stop when
the can is open.
8. Hold can and push front of cutting
assembly to release can. See Figure 4.
1. Unplug cord from electrical outlet.
2. To remove cutting assembly, turn
release button clockwise. See
Figure 5. Then remove cutting
assembly.
3. Wash cutting assembly in hot, soapy
water. Rinse and dry thoroughly.
4. Or remove flip-up magnet and place
the cutting assembly in automatic
dishwasher. To remove magnet,
grasp one side near hinge and pull
out slightly. See Figure 6. This will
release the magnet from the hinge.
Hand wash flip-up magnet.
5. Wipe body of can opener with damp
cloth. NEVER immerse the can
opener in water.
6. To reassemble, place cutting assembly into position and firmly press
both sides until the unit snaps into
place. See Figure 7. Replace
magnet if it was removed.
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Loading...