Haier WQP12-HFM ME User Manual

Domestic Dishwasher
WQP12-HFM
WQP12-HFM ME

Code:0120502225

GB

NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and
proper installation, use and maintenance of the appliance.

This appliance complies with the following EEC

directives:

-73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.

- Carefully dispose of the packing material.

- After removing the packing, check to make sure that the appliance
is not damaged. If in doubt, contact a qualified professional.

- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.

- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be exces­ sively or dangerously bent or flattened;

Safety Is a Good Habit to Get Into

Close-up View (control panel)

A
B
C

ON-OFF Light

ON-OFF Button

Handle For Opening Door

D
E
F
G

"Eco" Button

A

FE

Low Salt Indicator Light

"1/2" Button

* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.

- Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.

- This appliance cannot be installed outdoors, not even if the area
in which it is installed is covered by a roof; it is also very dangerous
to leave it exposed to the rain and elements.

- Do not touch the heating element during or after a wash cycle.

- Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.

- If the appliance malfunctions, turn off water supply to the appli­ ance and disconnect the plug from the wall socket. Then, con­ sult the section entitled, "Troubleshooting". If you cannot resolve
the problem, contact a service centre.

- Only specialised personnel are authorised to make repairs.

- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the
door lock.

- The appliance must be positioned so that the plug is accessible.

- The carpet must not obstruct the opening when the appliance installing
on the ground with carpet.

- If the supply cord is damaged, it must be replaced by a special
cord or assembly available from the manufacturer or its service
agent.

.1.

GB

BC D

G

Knob For Selecting Cycle

Close-up View (Interior)

A
B
C
D

Upper Rack
Rack Height Adjustor

Top Spray Arm
Lower Rack

E
F
G
H

Washing Filter

Bottom Spray Arm

Detergent and Rinse Aid Dispenser
Salt Container Cap

Technical characteristics

Width

60 cm

Depth

60 cm

Height

85 cm

Capacity

12 standard place settings

Mains water pressure

0.03-0.6 MPa

Power voltage

220V~

2000W

Total absorber power

.2.

GB

Salt







Salt

The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a
salt specifically designed to eliminate lime and minerals from
the water.

Loading the Salt into the Softener

Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:

- Remove the lower rack and then unscrew and remove the cap
from the salt container;

- If you are filling the container for the first time, fill it with water;

- Place the end of the funnel (supplied) into the hole and intro­ duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.

- Carefully screw the cap back on.

The salt container should be filled after about every 30 wash
cycles.

To prevent the formation of rust, load the salt just before begin­ning a wash cycle.

Adjusting Salt Consumption

The dishwasher is equipped with a system to adjust the level of
salt consumption in function of the hardness of the water being
used in order to optimize and customize the level of salt con­sumption while keeping it to a minimum.
To adjust the salt consumption level, follow these instructions:

- Unscrew the cap on the salt container;

- On the neck of the container there is an arrow (see above the
figure). If necessary, turn the arrow in the anti-clockwise direction
from the "-" setting to the "+" setting based on the hardness of
the water being used.

- It is highly recommended that the table be consulted when making
adjustments .

.3.

GB

Water Hardness

Clarke
degrees

ºdH

mmol/l

Selector
position

Salt
consumption
(Grams/cycle)

Autonomy
(cycles/2kg)

014 MNT MNIT

NIUQIQNUQQNQPS

PSTN QRUV QIRUIV

[UV[TN [UIV

L

=?J?

jba

LM

OM

QM

SM?H?

SM

QM

OR

Level

1

2

3

4