Haier WM6002A User Manual
User's manual
WM6002A
Computerized Full-auto
Washing Machine
TWO DRIVE
TWO 50% CONSUMPTION SAVER
Please read this manual carefully before using.
Retain it for future reference.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
The manufacturer will not take responsibility for those
risks occurred from not obeying this manual.
CONTENTS
Before using
Names of the parts.............the 2nd cover
Safety precautions .............................................1
Installation and adjustment .........................3
Install the water inlet hose............5
Using process
Preparation before washing ...............7
Put in the laundries .............................8
Put in the detergent ............................9
Use the operation buttons ...................10
Close the top lid .................................14
Finish washing ...................................14
Disposal after washing .........................15
Trouble shooting..............................16
Packing list.....................................17
Specification................the back cover
Names of the parts
Before Using
Before Using
Top lid component
Inner cover component
Detergent box
Control pannel
Outer tub cover
Lint filter fixing
Balance ring
Inner tub
Lint filter
Filter cover
Pulsator
Attachment block
(3 pieces)
Cabinet
Liquid whitener inlet
(3 pieces)
Fixed leg
Adjustable leg
Accessories
standby screws
and nut for earth-
ing wire
Adjustable leg film
water inlet valve
water absorption
cushion
power cord
round cover
back cover
rear faceplate
front control board
cabinet handle
drain hose hang-
ing hole
drain hose
drain hose jacket
the end connecting to the washing machine
Inner cover (1 piece)
one piece
Bottom plate (1 piece)
Fastening screws
ST4X16-A (8 pieces)
Water inlet hose (1 piece)
Water inlet hose joint (1 piece)
Meaning and description of the symbols
Contents marked with that symbol are related to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents.
jointer connecting the water
inlet hose and the water faucet
the end connecting to the water
inlet hose jointer
Lint filter (1 piece)
Contents marked with that symbol are actions forbidden to perform. Performing of those
action may result in damage of the machine or influence the personal safety of the users.
Safety precautions
Before Using
Before Using
Please plug the plug on special 220-240V AC receptacle.
Be sure to use three phase power receptacle.Ensure
the earthing prong of the power receptacle is earthed reliably.Use leakage protector if possible.
earth
Do not bend, stretch, twist, bind the power cord by force, or reformit.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent,or the after-sales service
department to avoid any risk.Keep the prong of the power plug clean.If
dust is found on the power plug, please wipe it off with dry cloth.
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hand.
Be sure to pull the plug off and close the water faucet
when occurring power failure,delivering the machine,
setting the machine idle or cleaning the machine,Do
not plug or pull the power plug with wet hand.
Do not use water with temperature higher than 50
The ventilation
holes at the bottom
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the control panel coating
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
.
Do not wash water-proof laundry like the raincoat,
bikecovers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries.
Safety precautions
Before Using
Before Using
Do not put hand into the rotating tub.It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not decompose, repair or alter the machine by
yourself.
Do not wash laundry with volatile materials
(such as thinner, petrol etc.).
Benzene
The handicapped or children without care shall not
use the machine.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
Keep the machine away from direct sunlight and
heat source like the heater.
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpins
and other foreign materials before washing.
Dismantle
Install
Dismantle
Install
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
Before Using
Installation and adjustment
Before Using
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
Install the inner cover and lint filter
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming
the inner cover shaft to the installation hole of the corresponding
outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the correspon
-ding outer tub cover shaft groove, then push the another inner
cover shaft into the corresponding outer tub cover shaft groove.
Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner
cover, and the operation shall be smooth. Do not dismount the
inner cover component after washing.
4.Install the lint filter in the balance ring.(See to the right figure)
Install the bottom plate
After opening the package, please lean the washing
machine gently down on soft items (like towel cloth,
blanket, etc.). Installthe bottom plate to the bottom of
the machine with eight screws by a cross screwdriver,
then lift the machine up gently. (See to the figure)
Outer tube cover
Inner cover shaft
Inner cover
Install the lint filter
Back
Front
bottom plate
Soft object
Screw
Adjust the Installation position
The washing machine away from wall should be overrun 20mm.The largest allowable slope of the shank base of
the machine is 2 .The slanting or rough ground will result in unstable running or stoppage of the machine.
Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
High
Low
the adjustable nut
FastenLoosen
the adjustable foot
How to change the direction of the drain hose
Before Using
Before Using
1. Dismount the back cover of the washing machine.
2. Put down the drain hose. Take off the drain hose
frame. As indicated in Figure 1, put the drain hose
into the cabinet. Then put one hand into the cabinet
to nip the claw of the drain hose bushing to release
the claw from original position. Take off the drain
hose bushing with the other hand. (As indicated in
Figure 2 and 3).
hose
drain
g
u
re
Fi
1
hose bushing claw
frame
cabinet
i
Push
Push
drain hose
nner
drain
t ake off
gu
Fi
Fi gur e 2
drain hose bushing
drain protecting cover
hose bushing
re
3
3. Dismount the protecting cover of the drain
outlet at the other side ( method the same as
the drain hose bushing). Install the drain hose
bushing as per indicatedin Figure 4.
4. Extend the drain hose from the other side.
Fix the drain hose onto the cabinet with the
drain hose rack. (As indicatedin Figure 5)
••••• •• •• ••••••••••••
Fi gur e 4
dr ai n hose bushing
Fi gur e 5
Fi gur e
6
Attention: To guarantee the proper installation, it is suggested to have the direction changing of drain
hose performed by the after-sales service technicians of our company.
Useage the drain hose
The drainage shall be smooth with the drain hose.
The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and cost
such long time that the machine may stop at mid
way.
Do not step on or press the drain hose.
<10cm
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
> 30mm
<1.5m
If the extra hose is too long,cut
it either at A or at B point.
B
A
A
Loading...