Haier Service-1200 User Manual

Service

Twin-tub Washing Machine with Pump

User's manual

Model:Service-1200

Please read this manual carefully before using.
Retain it for future reference.

0030806758C

Contents

Names of the parts

Safety precautions
Installation and adjustment

Preparation before washing

The musts in washing

Usage of the detergent

Washing sequence

Disposal after washing

Trouble-Shooting *Answer to question

Packing list *Specification

Names of the parts

Water-filling entrance

Water inlet selector handle

Buzzer

Wash selector

Wash timer

Control panel

Overflow filter

Lint filter

Wash tube

Pulsator

Wash tube cover

Drain hose

Outer cover of the spin tub

Inner cover of the spin tub

Spin timer

Spin tub frame

Spin tub

Valve cover

Cabinet

Base frame

Notes: All illustrations in this Manual are given for reference only. Your
products and accessories may show differences from these
illustrations due to our continuous improvement.

Meaning and description of the symbols

Warning sign

Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.

Forbidding sign

Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.

Please check if the power receptacle has good earthing
condition before using to guarantee your safety.

1

Safety precautions

Please insert the power cord into
special receptacle with rated vol­tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.

When the machine is normally
using, please put the power plug
at the location easily to be insert­ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.

If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.

Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.

Ventilation hole at
the bottom of the
washing machine

Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.

Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.

2

Safety precautions

Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.

Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.

Handicapped or children without care
shall not use the machine.

Do not decompose, repair or alter the
machine by yourself.

Do not wash laundries with volatile
materials (such as thinner, petrol etc.).

Petrol

Thinner

Keep the machine away from direct
sunlight and heat source like the
heater.

To protect your laundries and wash­ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.

Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.

It is suggested to use foamless washing
powder.

3

Installation and adjustment

Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.

Install the lint filter

Put the underside of the lint filter into overflow filter
then push the upside into overflow filter

overflow filter

After installation,please refer that the lint filter
installed to the right station,otherwise the lint
filter may be falled off when washing,influencing
your use.

Usage of the drain hose

The drainage shall be smooth with the drain hose.

1.put the drain hose up to suitable position.

2.Do not tramp or press the drain hose.

lint filter

H

0.7m<H

<1.2m

4

How to change the direction of the drain hoses

Figure 1 indicates the ex factory installation
position of the drain hose.

Extend the drain hose from the side of spin tub

Soft item

Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.

Drain hose fixing clamp

Back

Front

Figure 1

Dismantle the drain hose fixing clamp and take
the hose out of the fixing groove.
(See to Figure 2).

Soft item

Figure 2

Embed the drain hose into the groove along the side
of the spin tub in the order of (1)~(3), heading for the
side of the spin tub. (See to Figure 3).

Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.

Extend to the
spin tub side

Embed into the
groove in turn

Figure 3

Install the water inlet hose; Select the water level

Insert the water inlet hose into the water-filling
entrance on the control panel

To dismantle the water inlet pipe,
just push the control handle as indicated in the
figure and pull it out

Maximum

Select water level according to the
quantity of the laundries.
Set the water level adjusting lever

Medium

Minimum

to needed line.

5

Water inlet hose

Water level
indicator

Max

Med

Min

Water level
adjusting lever

Water-filling
entrance

Preparation before washing

Preparation before washing

1.Connect the water inlet hose.

2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.

3.Put the drain hose up to suitable position.

4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.

Pay attention to followings before washing the laundries

Check if
the laundries
has special
requirement
on washing

Clear the
pocket. Take
out the coins,
sand, hairpins
etc.

Tie the long
strips; fasten
the buttons;
close zippers.

The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.

When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.

a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.

6

The musts in washing

The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity.

The thickness ,size , type of the cloth will influ­ence the actual washing capacity. It is suit­able to put in reasonable amount of laundries
and the laundries can be turned round in wash­ing for one time washing.
Do not select " Maximum " water level for
laundries less than 4.0kg , so as to avoid splash­ing of water.

It is suggested not to use high sudsing detergent.

Usage of the detergent

How to use the whitener

Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into thewashing tub.

Avoid using whitener on laun­dries with color or pattern as they
are prone to lose color.

The whitener shall not touch
the laundries directly.

Refer to the user's manual for
the usage and quantity of the
whitener.

For powder whitener, please
dissolve it before using.

How to use the washing powder

Direct dissolved in the machine:

1.Fill small quantity of water.

2.Add the powder . Run for 30
seconds to dissolve it completely.

3.Put it in the laundries. Select suitable
water level.

The instant dissolving of the washing
powder:

1.Prepare warm water of 30 C and a
container.

2.Add the powder while stirring to fully

dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.

Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.

7

Washing sequence

Water-filling selector

Wash timer

(To set to below 2 minute,
first set to 5 minute then
turn it back. it can increase
the service life of the timer).

OFF

WASH TIMER

Wash selector

(standard current,
strong current)

STRONG

STANDARD

WASH SELECTOR

Buzzer

(The buzzer will ring when
the washing finishes)

OFF

MAX

DRAIN

BUZZER

Wash

1.Water-filling selector
Set the water inlet selector at the "WASH" side.
(Figure 1)

2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.

3.Put in the laundries. If the water quantity is
insufficient, please add water.

4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)

5.Select the washing time
Select the washing time according to the laundries.
(Figure 4)

Water-filling entrance

WASH

STRONG

STANDARD

WASH SELECTOR

WASH TIMER

Spin timer

(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).

OFF

SPIN TIMER

SPIN

Figure 1

Figure 2

DRAIN

Figure 3

OFF

Figure 4

6.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).

8

STRONG

STANDARD

WASH SELECTOR

DRAIN

Figure 5

Midway spinning

1.Put the laundries into the spin tub evenly and smoothly.

2.Spin

(1) Put the gland in properly.

Please put in the gland properly even if the

laundries quantity is small.

Push

Gland

Push

Proper

The laundries
are slanting

(2) Close the inner and outer cover of the spin tub.

Outer cover of
The spin tub

(3) Spin for 1-2 minutes.

3.Run the foam-removing spinning.

1

Set the inlet selector handle on spin side and

fill water for about 1 min.

In case water flows out from wash tub side

due to too much inflow, please turn down

the water tap a bit.

2

Close the spin tub outer cover and spin

for about 1 - 2 min.

Proper

No gland

Inner cover of
The spin tub

WASH

SPIN

9