Haier QDT125 Series Owner's Manual

18” Built-In Dishwasher Lave-Vaisselle Incorpere 18” Lavavajillas Empotrado 18”

Owner's Manual

Manuel d’utilisation

Manual del propietario

QDT125 Series

49-55125-1 05-18 GEA

ENGLISH

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................................................3

USING THE DISHWASHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Getting Started ........................................................................................................ 5

Dispensers ............................................................................................................ 6

Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CARE AND CLEANING ............................................................................................10

TROUBLESHOOTING TIPS ........................................................................................12

LIMITED WARRANTY .............................................................................................15

CONSUMER SUPPORT ........................................................................................... 16

RECORD KEEPING

Thank you for purchasing this Haier product. This Owner's Manual will help you get the best performance from your new dishwasher.

For future reference, record the model and serial number located on the the tub wall just inside the door.

Staple your proof of purchase to this manual to aid in obtaining warranty service if needed.

____________________________________________________ Model number

____________________________________________________ Serial number

____________________________________________________ Date of purchase

2 49-55125-1

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

ENGLISH

WARNING

For your safety, the information in this manual must be followed to minimize the

risk of fire, explosion, electric shock, and to prevent property damage, personal injury, or death.

WARNING

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at haierappliances.com.

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an equipmentgrounding conductor with the circuit conductors and connect to the equipment-grounding terminal or lead of the appliance.

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

Dispose of discarded appliances and shipping or packing

material properly.

PROPER INSTALLATION AND MAINTENANCE

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

Use only cord kit WX09X70910 or hard-wire to building

electrical. Failure to follow this instruction, could result in risk of fire and personal injury.

To minimize the possibility of electric shock, disconnect

this appliance from the power supply before attempting any maintenance.

NOTE: Turning the dishwasher off does not disconnect

the appliance from the power supply. We recommend having a qualified technician service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

Use only detergents or wetting agents recommended

for use in a dishwasher and keep them out of reach of children. Using a detergent that is not specifically designed for dishwashers will cause the dishwasher to fill with suds.

Locate sharp items so that they are not likely to damage

the door seal.

Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

Do not wash plastic items unless marked dishwasher

safe or the equivalent. For plastic items not so marked, check the manufacturer’s recommendations.

READ AND SAVE THESE INSTRUCTIONS

Do not operate your dishwasher unless all enclosure

panels are properly in place.

Do not tamper with controls.

Do not abuse, sit on or stand on the door or dish rack of

the dishwasher.

To reduce the risk of injury, do not allow children to play

with, on or inside this appliance at any time.

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.

Small parts can be a choke hazard to small children if

removed from the dishwasher. Keep out of reach of small children.

49-55125-1 3

ENGLISH

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks. HYDROGEN GAS IS EXPLOSIVE. If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.

WARNING

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting rid of your dishwasher, please follow the instructions below to help prevent accidents.

Do not allow children to play with, on, or inside this or any discarded appliance.

Take off the door of the washing compartment or remove the latch by disengaging

the two retaining snaps using a flat-blade screwdriver (as shown).

CAUTION

During or after wash cycle, contents may be hot to the

touch. Use care before handling.

Close supervision is necessary if this appliance is used

by or near children. Do not allow children to play around the dishwasher when closing the door, closing the upper rack, or while vertically adjusting the upper rack due to

WATER HEATER SAFETY

RISK OF CHILD ENTRAPMENT

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

the possibility of small fingers being pinched.

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and paint brushes in your dishwasher. Damage to the dishwasher and discoloration or staining of the dishwasher may result.

Disengage

both

retaining

snaps

CAUTION

This appliance must be supplied with 120V, 60 Hz, and

connected to an individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time-delay fuse.

If the electric supply provided does not meet the above

ELECTRICAL REQUIREMENTS

NOTICE

ʄ

If your dishwasher is connected to a wall switch, ensure that the switch is on prior to use.

ʄ

If you choose to turn the wall switch off between wash cycles, allow 5-10 seconds after turning the switch on before touching Start to allow the control to initialize.

READ AND SAVE THESE INSTRUCTIONS

4 49-55125-1

specifications, it is recommended that a licensed electrician install an approved outlet.

Your dishwasher circuit should not be used for any

other appliance while the dishwasher is in operation as the dishwasher requires the full capacity of the circuit.

ʄ

Use only powder, Finish Dishwashing Detergent, liquid detergents or rinse

agents recommended for use in a dishwasher and keep them out of the reach of children. Finish® Quantum®

Automatic Dishwashing Detergent, and Finish Dry® Rinse Aid rinse agents have been approved for use

in all Haier Appliances dishwashers.

Quantum® Automatic

Jet-

USING THE DISHWASHER

Features and appearance will vary throughout this manual

Clean

Sanitized

LOAD DISHWASHER

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of normal food

Hold 3 Sec To Cancel

Start

1-12 hrs

Delay Start

Heavy

AutoSense

Light

Cycle

Select

Hold 3 Sec

Wash Temp

soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat trimmings, and excessive amounts of grease or oil.

ADD DETERGENT

Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish® Quantum® Automatic

Dishwashing Detergent. See Dispensers section.

ADD RINSE AGENT

Add rinse agent such as Finish® Jet-Dry® Rinse Aid to the rinse agent dispenser. See Dispensers section. NOTE: The

use of rinse aid can further enhance the dishwasher’s drying performance.

SELECT CYCLE

Open the door and press the Cycle Select pad for the desired wash cycle. The light next to the Cycle Select pad will be lit to indicate which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected. The cycle must be selected with the door in the open position. The cycle will not start until the Start pad is pushed and

the door is closed within 4 seconds. AutoSense This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant for daily,

regular, or typical use to completely wash a full load of normally soiled dishes and is designed to conserve both water and energy. NOTE: AutoSense was used to rate the energy efficiency of this dishwasher.

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle.

Light This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected.

ENGLISH

Boost Sanitize

SELECT OPTIONS

Wash Temp

Boost This option raises the water temperature and extends the cycle time in order to achieve better wash

Sanitize

Delay Start This option allows you to delay the start of a wash cycle for up to 12 hours. With the door open and a

Control Lock

Allows you to select a higher wash temperature. These options are only available for Heavy and AutoSense cycles. Press the Wash Temp pad until the light next to the desired option comes on.

performance.

This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length may vary depending on the temperature of your inlet water. NOTE: Cycles using this option are monitored for sanitization requirements. If the cycle is interrupted during or after the main wash portion or if the incoming water temperature is so low that adequate water heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the Sanitized light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the requirements of Section 6, NSF 184 for soil removal and sanitization efficacy. NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

cycle selected, press the Delay Start pad to choose the number of hours you want to delay the start of the wash cycle. The hours will show in the display window. NOTE: You may cancel the Delay Start timer by holding the Start pad for 3 seconds. This will also cancel the wash cycle.

You can lock the controls to prevent selections from being made. You can also lock the controls after you have started a cycle to prevent cycle changes. For example, children cannot accidentally start the dishwasher by pressing pads with this option selected.

To LOCK/UNLOCK the dishwasher control, press and hold the Cycle Select and Wash Temp pads for 3 seconds. The lock control light ( ) will turn on to indicate the control is locked and will turn off to indicate the control is unlocked.

49-55125-1 5

ENGLISH

USING THE DISHWASHER

START DISHWASHER

Start Press the Start pad and close the door within 4 seconds to start the cycle or begin the Delay Start

countdown. The Start light will turn on. The wash cycle will begin after 10 seconds and then pump out for 60 seconds prior to filling the dishwasher with water. To activate the display, press any pad with the door open.

Interrupt or Pause

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

INDICATOR LIGHTS

Sanitized Displayed at end of the cycle when Wash Temp - Sanitize has been selected and dishwasher has met

Clean Displayed when a wash cycle is complete. The light stays on as a reminder that the dishes are clean.

DISPLAY

Time Remaining

To interrupt or pause a cycle, slowly open the door. Opening the door will cause the wash cycle to pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume the cycle, press Start, and close the door within 4 seconds. If the door is not closed within 4 seconds, the Start light will start blinking and the dishwasher will beep once every minute to signal that the cycle did not restart. If the Start light is blinking, the dishwasher is waiting for input.

The dishwasher will dr

requirements for sanitization. See Wash Temp - Sanitize, for complete description. Opening the door will turn off the light.

Opening the door will turn the light off.

During operation, the display shows the total number of minutes remaining in the cycle. During a delay start, the display will show hours of time remaining until the cycle starts.

ain, emit a beep sound, and the wash cycle light will turn off.

CHECK THE WATER TEMPERATURE

The entering water should be at least 120°F (49°C) and not more than 150°F (66°C) for effective cleaning and to prevent dish damage. Check the water temperature with a candy or meat thermometer.

Turn on the hot water faucet nearest the dishwasher, place the thermometer in a glass and let the water run continuously into the glass until the temperature stops rising.

SABBATH/DOOR WAKE UP MODE

To turn this option ON/OFF, press and hold the Start and Wash Temp buttons for 5 seconds, close the door and wait 3

minutes for the dishwasher to go into sleep mode. In the OFF mode, the control display, control sounds, and interior lights (on some models) will not respond to the door opening/ closing. This mode can be used when observing certain religious holidays such as the Sabbath. To activate the control and interior lights (on some models), press any button.

DISPENSERS

Use a Rinse Agent

Rinse agents, such as Finish® Jet-Dry® Rinse Aid are designed for great drying action and to protect against spots and film build-up on your dishes, glasses, flatware, cookware, and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.9 oz. (115 ml) of rinse agent. Under normal conditions, this will last approximately one month.

Make sure the dishwasher door is fully open.

Open the dispenser door. (Rinse agent compartment is

on the right side of dispenser.)

6 49-55125-1

Slowly add rinse agent until the cup is full. You may need

to pause several times to allow rinse aid to settle.

Clean up any spilled rinse agent with a damp cloth to

prevent foam from forming inside the dishwasher.

Close the dispenser door.

USING THE DISHWASHER

DETERGENT DISPENSER

To open, press the button and the cover will flip back. The detergent dispenser has two compartments. The pre-wash compartment is the smaller compartment on the left side. Use the pre-wash compartment only when your water is extremely hard or when you have a heavy soiled load. The pre-wash compartment is not used when tablet or packet detergents are used.

NOTE: Do not block detergent dispenser with large or tall utensils.

Detergent Dispenser

You may use tablet, packet, powder, liquid or gel automatic dishwasher detergent. Make sure you use only detergents specifically labeled for use in automatic dishwashers. Never use liquid hand dish detergent in an automatic dishwasher. Sudsing and poor wash performance will result with the use of improper detergents.

Detergents should be stored in a dry location and in their original container to prevent loss of effectiveness. Place detergent in the cup just prior to starting the dishwasher and then close the cover. The cover will open during the wash cycle.

FILLING THE DETERGENT

Main Wash

Pre-Wash

Rinse

Agent

Use the table as a starting point and then adjust the amount of detergent you use. Use just enough to get good wash performance. Using just the right amount of detergent will provide great wash performance without wasting detergent or etching glassware.

Number of

Grains/Gal.

Less than 5 Fill main cup to line 20

5 to 10 Fill main cup to line 30

Greater than 10

Using too much detergent with very soft and/or very hot water may cause a condition called etching on your glassware. Etching is a permanent cloudiness in your glassware. This condition is irreversible. However, using too little detergent will cause poor wash performance.

Detergent Cup(s) to Fill

Fill both main cup

and pre-wash cup

DO NOT USE HAND DISH DETERGENT

ENGLISH

DISPENSER

We recommend using detergent in tablet or packet form. Independent testing has shown this form of detergent is very effective in the dishwasher. Finish® Quantum

Powerball® is an example of this type of detergent. Simply

put a tablet or packet into the main wash compartment and close the detergent cup cover. Please notice that the tablet or packet must be placed in the main wash compartment of the detergent cup. If the tablet or packet is placed in the prewash compartment or tossed in the bottom of the dishwasher, the detergent will be flushed down the drain in a very short period of time and will thus be wasted. Wash performance will be very poor as a result.

If you choose to use detergent in powder, liquid or gel form, the amount of detergent you use will be determined by the hardness of your water, the temperature of your water, and the food soil load inside the dishwasher. Contact your water company to get information about the hardness of the water in your area. Water hardness is measured in grains per gallon. Use this information and the table above to determine the amount of detergent to use. You may purchase a hard water test strip from Haier Appliances. Call 877-337-3639 and ask for part number WD01X10295. In Canada, call 800-661-1616.

NOTE: Using a detergent that is not specifically designed for

dishwashers will cause the dishwasher to fill with suds. During operation, these suds will spill out of the dishwasher vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike, store the dishwasher detergent in a separate space from all other cleaners. Show anyone who may use the dishwasher the correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher, your dishes will not get clean using a dishwashing detergent that is not formulated for automatic dishwashers.

49-55125-1 7

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model.

UPPER RACK

The upper rack is for glasses, cups, and saucers. This is also a secure place for dishwasher-safe plastic items. The upper rack can be used for odd sized utensils. Sauce pans, mixing bowls, and other similarly shaped items should be placed face down for best wash performance.

The cup shelf may be placed in the up or down position to add flexibility.

IMPORTANT: Ensure that items do not protrude through the bottom of the rack where they will block the rotation of the upper spray arm. This could result in noise during operation and/or poor wash performance.

UPPER RACK - ADJUSTMENT

CAUTION

injury or damage to the contents, do not raise or lower the upper rack after the rack is loaded.

The upper rack may be adjusted to items.

To adjust the upper rack:

Fully extend the upper rack and rotate open the two plastic

end caps

Remove the upper rack.

Select the set of rollers on the side of the rack that

provides the desired height, and reinstall the upper rack by guiding the rack rails between the appropriate set of rollers.

on the front of the rails.

A loaded upper rack may be heavier than anticipated. To prevent minor

accommodate larger

Remove:

Replace:

End Cap

Rollers

Rail

8 49-55125-1

Rail

End Cap

With the rack reinstalled, rotate closed the two plastic end

caps, ensuring properly engage the from the dishwasher.

the snap is properly engaged. Failure to

end caps may result in the rack falling

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model.

LOWER RACK

When loading the lower rack, do not load large platters or trays in the front left. They may prevent detergent from

circulating during the wash cycle. The lower rack is best used for plates, saucers and cookware. Large

items should go along the sides. Load platters, pots along the sides, in corners or in the back. The items should face the center of the rack.

and bowls

soiled side of

SILVERWARE BASKET

The silverware basket may be used without the topper for quick loading. With the topper, flatware is better positioned for the dishwasher to thoroughly wash and dry all pieces by preventing nesting.

Without the topper

Put the flatware in the removable basket with fork and knife handles up to protect your hands. Place spoons in the basket with handles down. Mix knives, forks and spoons so they don’t nest together. Distribute evenly. Small plastic items, such as measuring spoons and lids from small containers, should go in the bottom of the silverware basket with silverware on top.

ENGLISH

IMPORTANT: Ensure that items do not protrude through the

bottom of the rack or the silverware basket where they will block the rotation of the lower spray arm. This could result in noise during operation and/or poor wash performance.

With the topper

Place small plastic items, such as measuring spoons and lids from small containers, in the bottom of the basket and snap the topper in place. Insert spoons and forks, handles first, through the holes in the topper. Place knives, blades first, through the holes in the topper.

IMPORTANT:

may block the detergent dispenser or upper spray arm. This could result in noise during operation and/or poor wash performance.

Do not load large or tall utensils where they

49-55125-1 9

ENGLISH

CARE AND CLEANING

CONTROL PANEL

To clean the control panel, use a lightly dampened cloth. Then dry thoroughly.

EXTERIOR DOOR PANEL

Before cleaning the front panel, make sure you know what type of panel you have. Refer to the last two letters of your model number. You can locate your model number on the left-hand tub wall just inside the door. If your model number ends with BB or WW then you have a painted door panel. If your model number then you have a Stainless Steel door panel.

Follow the instructions below for cleaning the door panel for your specific model.

Painted Door Panel (model numbers ending in BB–black or WW–white)

Use a clean, soft, lightly dampened cloth, then dry thoroughly Do not use scouring pads or powered cleaners because these

products can scratch the finish.

Stainless Steel Door Panel (model numbers ending in SS) For cleaning rust and tarnish, cleaners with oxalic acid such

as Bar Keepers Friend Soft Cleanser™ will remove rust, tarnish and small blemishes. Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge. Do not use appliance wax or polish on the stainless steel.

For other blemishes and marks, use Stainless Steel Magic or a similar product using a clean soft cloth. Do not use appliance wax, polish, bleach or products containing chlorine on Stainless Steel. You can order Stainless Steel Magic # WX10X29 through Haier Appliances Parts by calling 877-337-3639. In Canada, call 800-661-1616.

ends with SS,

SPRAY ARMS

Because hard water chemicals will clog the spray arm jets and bearings, it is necessary to clean the spray arms regularly. Wash the arms in soapy, warm water and use a soft brush to clean the jets. Replace them after rinsing thoroughly.

To remove the upper spray arm, twist the retaining nut 45° and pull the spray arm off the water supply tube.

Water Supply Tube

Upper

Rack

Upper Spray Arm

IMPORTANT: When replacing make sure to twist lock the retaining nut securely onto the water supply tube. Check that the spray arm is secure and that it rotates freely.

To remove the lower spray arm, remove the lower rack and lift spray arm out.

Arm

Clips

Retaining

Ring

Retaining nut

Lower Spray Arm

DISHWASHER INTERIOR

To clean and de-odorize your dishwasher, use citric acid or

Finish® Dishwasher Cleaner, a detergent additive. Finish® Dishwasher Cleaner will break up mineral deposits, and

remove hard water film and stains. You can order citric acid Haier Appliances kit #WD35X151

through Haier Appliances Parts by calling 877-337-3639 or visiting haierappliances.com. In Canada, call 800-661-1616. You can purchase Finish® Dishwasher Cleaner at your local grocery store.

UPPER SPRAY HEAD

Do NOT remove the upper spray head.

Clean with warm soapy water using a small plastic bristle brush.

10 49-55125-1

IMPORTANT: When replacing make sure to seat the arm clips over the retaining ring. Check that the spray arm is secure and that it rotates freely.

CARE AND CLEANING

FILTER ASSEMBLY

Inspect and clean the filters periodically. This should be done every month or more depending on usage. If there is a decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.

Lower Spray Arm

To clean the filter assembly, remove the bottom rack and lower spray arm. Twist the filter assembly counterclockwise and lift to remove. Remove the filter plate.

Filter Assembly

Filter Plate

STAINLESS STEEL INNER DOOR AND TUB

The stainless steel used to make the dishwasher tub and inner door provides the highest reliability available in a Haier Appliances dishwasher.

If the dishwasher tub or inner door should be scratched or dented during normal use, they will not rust or corrode. These surface blemishes will not affect their function or durability.

PROTECT AGAINST FREEZING

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

Turn off electrical power to the dishwasher. Remove fuses or

trip circuit breaker.

Turn off the water supply and disconnect the water inlet line

from the water valve.

Drain water from the water inlet line and water valve. (Use a

pan to catch the water.)

Reconnect the water inlet line to the water valve.

ENGLISH

Twist counterclockwise and lift to remove

Rinse the filters with warm soapy water. Scouring pads or brushes can scratch the filter surfaces but a soft brush or sponge may be needed to remove stubborn soils or calcium deposits caused by hard water.

Press tabs on

the fine filter

and pull to

separate from

the coarse filter

Once cleaned, replace the filter plate, insert the filter assembly through the plate and twist it clockwise until it locks in place. Make sure the filters are fully seated as improper replacement of the filters may reduce the performance level of the appliance. Replace the lower spray arm and lower rack.

IMPORTANT: Before replacing, make sure no objects have fallen into the opening in the bottom of the dishwasher.

Filter Plate

Fine Filter

Coarse Filter

Replace the filter plate.

Snap the fine filter back

into the coarse filter. Place filter assembly

through the filter plate

and twist clockwise to

lock into the dishwasher

DOES YOUR DISHWASHER HAVE AN AIR GAP?

An air gap protects your dishwasher against water backing up into it if a drain clogs. The air gap is not a part of the dishwasher. It is not covered by your warranty. Not all plumbing codes require air gaps, so you may not have one.

Air gap

Check the air gap any time your dishwasher isn’ t d raining well.

The air gap is easy to clean:

Turn off the dishwasher and lift off the air gap cover.

Remove the plastic cap under the cover and clean with a

toothpick.

Replace the cap and cover when the air gap is clean.

If the dishwasher tub or inner door should be scratched or

dented during normal use, they will not rust or corrode. These surface blemishes will not affect their function or durability.

49-55125-1 11

ENGLISH

Start status indicator light flashing

Dishwasher BEEPS once every minute

Beeping at the end of the cycle

Dishes and flatware not clean

Spots and filming on glasses and flatware

Cloudiness on glassware

Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

The door was opened or the cycle was interrupted.

This is a reminder that your dishwasher door has been left open during operation. It will continue beeping until you press Start and close the door.

This is normal. Dishwasher will beep at end of cycle.

Filter assembly is clogged See the CARE AND CLEANING section. Low inlet water temperature Make sure inlet water temperature is correct (see the USING

Water pressure is temporarily low

Air gap or disposer clogged Clean the air gap or flush the disposer. High drain loop or air gap not

installed Improper rack loading Make sure large dishware or utensils do not block the detergent

Poor performing detergent Use a highly rated detergent such as Finish® Quantum®

Extremely hard water Use rinse agents such as Finish® Jet-Dry® Rinse Aid to prevent

Low inlet water temperature Make sure inlet water temperature is at least 120°F (49°C). Overloading or improper

loading of the dishwasher Old or damp powder

detergent Rinse agent dispenser empty Too little or low performing

detergent Combination of soft water

and too much detergent

Low performing phosphatefree detergent

Water temperature entering the dishwasher exceeds 150°F (66°C)

Rinse agent was spilled Always wipe up rinse agent spills immediately.

Press the Start pad once and close the door within 4 seconds to start the dishwasher. Press the Start pad a second time when the dishwasher is running only if you wish to cancel the cycle.

Press Start and close the door.

The dishwasher will beep (unless interupted) and the Clean light will display at the end of the wash cycle.

THE DISHWASHER section). Turn on the hot water faucet nearest the dishwasher, let run until the water temperature stops rising. Then start the dishwasher and turn off the faucet. This ensures the entering water is hot. Select Wash Temp - Boost.

Turn on a faucet. Is water coming out more slowly than usual? If so, wait until pressure is normal before using your dishwasher. water pressure to the dishwasher should be 20-120 psi.

Refer to the Installation Instructions for proper drain line installation.

dispenser or the wash arms. See the Loading section.

Automatic Dishwashing Detergent.

spots and prevent new film build-up.

If water is extremely hard, a softener may be required.

Load dishwasher as shown in the Loading section.

Make sure detergent is fresh. Use a highly rated detergent such

as Finish® Quantum® Automatic Dishwashing Detergent.

Refill with rinse agent such as Finish® Jet-Dry® Rinse Aid. Make sure you use the proper amount of highly rated

detergent. This is called etching and is permanent. To prevent this from

happening, use less detergent if you have soft water. Wash glassware in the shortest cycle that will get it clean.

See A white film on glassware, dishware and the interior in this TROUBLESHOOTING TIPS section.

This could be etching. Lower the water heater temperature.

Quantum® Automatic Dishwashing Detergent has

for use in all Haier Appliances dishwashers.

Normal

Finish®

been approved

12 49-55125-1

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Detergent left in dispenser cups

Black or gray marks on dishes

Dishes don’t dry Door not opened immediately

Control panel responded to inputs but dishwasher never filled with water

Stained tub interior An overall yellow or brown

Dishwasher won’t run Fuse is blown or circuit

Control panel lights go off when you’re setting controls

Water standing in the bottom of the tub

Water won’t pump out of the tub

Dishes or utensils are blocking the detergent cup

Aluminum utensils have rubbed against dishes

after Clean light came on

Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Rinse agent dispenser is empty

Door may not be completely closed

Water valve may be turned off Make sure water valve (usually located under the sink) is turned

film can be caused by iron deposits in water

White film on inside surface— hard water minerals

breaker is tripped Power is turned off In some installations, the power to the dishwasher is provided

Control panel is locked Unlock control panel. See the Getting started section. Reboot your control Turn off power to the dishwasher (at circuit breaker or wall

Time too long between touching of selected pads

Air gap is clogged Clean the air gap. See the CARE AND CLEANING section.

High drain loop or air gap not installed

Drain is clogged If you have an air gap, clean it. See the CARE AND CLEANING

Reposition the dishes, so the water from the lower spray arm can flush the detergent cup. See the Loading section.

Reposition the tall utensils or heavy silverware that may be keeping the dispenser cup door from opening. See the Loading section.

Remove marks with a mild, abrasive cleaner.

For proper drying, the dishwasher door must be opened immediately after the Clean light comes on.

Use Wash Temp Boost. Select a higher cycle, such as Heavy.

Check the rinse agent dispenser and fill as required.

Make sure the door is firmly closed.

on. A special filter in the water supply line is the only way to correct

this problem. Contact a water softener company.

We recommend water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral deposits. Citric acid (Part number: WD35X151) can be ordered through Haier Appliances Parts. See back cover for ordering information. Alternatively, purchase Finish® Dishwasher

Cleaner and follow the directions on the label.

Replace fuse or reset circuit breaker. Remove any other appliances from the circuit.

through a wall switch, often located next to the disposer switch. Make sure it is on.

switch) for 30 seconds, then turn back on. Each pad must be touched within 30 seconds of the others. To

relight, touch any pad again or open the door and unlock.

Refer to the Installation Instructions for proper drain line installation.

section. If the dishwasher drains into a disposer, run disposer clear. Check to see if your kitchen sink is draining well. If not, you may

need a plumber.

Finish® Jet-Dry® Rinse Aid to help prevent hard

ENGLISH

49-55125-1 13

ENGLISH

Sanitized light does not illuminate at the end of the cycle

Noise Normal operating sounds:

A white film on glassware, dishware and the interior

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

The door was opened and the cycle was interrupted during final rinse

The incoming water temperature was too low

Beeping at the end of the cycle

Detergent cup opening Water entering dishwasher Motor stops and starts at

various times during cycle Spray arms start and stop at

various times Drain pump sounds during

pump out Drain pump starts and stops

several times during each drain

Rattling dishes when the spray arm rotates

Rattling silverware against door during wash

This problem is likely caused by a low quality phosphatefree dishwasher detergent

Do not interrupt the cycle by opening the door during the wash cycle.

Raise the water heater temperature to between 120°F and 150°F.

These are all normal. No action is required.

Make sure dishes are properly loaded. See the Loading section.

Tall utensils may be placed in the upper rack to avoid bumping against inner door during wash cycle.

To remove the white film, run your dishes through a dishwasher cycle with citric acid. Use a WD35X151 citric acid kit found online. Otherwise, use Finish® Dishwasher Cleaner found at your local grocery store.

Pour the citric acid in the detergent cup and close the cover. Place the filmed but otherwise clean glassware and dishware in the dishwasher. Leave silverware and other metal items out of the dishwasher. Turn the dishwasher on and let it run through a complete cycle without detergent. The glassware, dishware, and dishwasher should come out film free. Alternatively, a vinegar rinse may be used. Pour 1 cup of vinegar into dishwasher just after the detergent cup opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed. The use of a rinse agent such as

may help minimize a repeat build up of film. Also, the use of a highly rated detergent such as Finish® Quantum® Automatic

Dishwashing Detergent will help prevent film build-up.

Finish® Jet-Dry® Rinse Aid

FORGET TO ADD A DISH?

Additional items may be added to the dishwasher at any time, ideally items would be added shortly after starting a wash cycle.

Open the door to interrupt the cycle. Pull the door handle

to release the door. Do not open the door all the way until the water spray

action stops. Steam may rise out of the dishwasher.

14 49-55125-1

Add additional items.

Press Start and close the door within 4 seconds to

resume the cycle.

LIMITED WARRANTY

haierappliances.com

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service online, visit us at haierappliances.com, or call Haier Appliances at 877-337-3639. Please have your serial number and Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a Haier Appliances factory service technician the ability to quickly diagnose any issues with your appliance and helps Haier Appliances improve its products by providing Haier Appliances with information on your appliance. If you do not want your appliance data to be sent to Haier Appliances, please advise your technician not to submit the data to Haier Appliances at the time of service.

For the period of Haier Appliances will replace One year

From date of the original purchase

Any part of the dishwasher which fails due to a defect in materials or workmanship. During this limited one-year warranty, Haier Appliances will provide, free of charge, all labor and in-home

service to replace the defective part.

your model number available when calling for service.

In Canada, call 877-470-9174.

What Haier Appliances will not cover (for customers in the United States):

ʄ Service trips to your home to teach you how to use the

product.

ʄ Improper installation, delivery, or maintenance. ʄ Failure of the product if it is abused, misused or used for

other than the intended purpose or used commercially.

ʄ Replacement of house fuses or resetting of circuit

breakers.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a Haier Appliances Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized Haier Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home. Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

ʄ Product not accessible to provide required service. ʄ Damage to the product caused by accident, fire, floods,

or acts of God.

ʄ Incidental or consequential damage caused by possible

defects with this appliance.

ʄ Cleaning or servicing of the air gap device in drain line. ʄ Damage caused after delivery including damage from

items dropped on the door.

date is needed to obtain service under the warranty.

ENGLISH

Staple your receipt here. Proof of the original purchase

Warrantor: Haier Appliances, Louisville, KY 40225

What Haier Appliances will not cover (for customers in Canada):

ʄ Service trips to your home to teach you how to use the

product.

ʄ Improper installation.

If you have an installation problem, contact your dealer or

installer. You exhausting and other connecting facilities.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within Canada. In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide.

are responsible for providing adequate

WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.

electrical,

ʄ Failure of the product if it is abused, misused or used for

other than the intended purpose or used commercially.

ʄ Replacement of house fuses or resetting of circuit

breakers.

ʄ Damage to the product caused by accident, fire, floods,

or acts of God.

ʄ Damage caused after delivery including damage from

items dropped on the door.

Warrantor: MC Commercial Inc., Burlington, ON, L7R 5B6

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

49-55125-1 15

+ 33 hidden pages

Haier QDT125 Series Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual