Haier LEC32B1380, LEC32B1380W Owner's Manual

TFT-LED LCD TV
LEC32B1380 LEC32B1380W
Contents
Safety and warnings.......................................................................................2-3
Introduction..................................................................................................4
Stand installation guide................................................................................. 5
Remote Control............................................................................................10
Operation..................................................................................................... 11-15
Trouble Shooting...........................................................................................16
DVD Operation............................................................................................. 17-20
DVD Trouble Shooting...................................................................................21
Warranty.......................................................................................................2 2
-1-
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install in accordance with the instructions.
8) Do not install near any heat sources such as radiations, heat registers, stoves, or other (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protected the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
Television.
11) Only use attachments/accessories specified by the manufacturer.
12) Unplug this during lighting storms or when unused for long periods of time.
13) Refer all servicing to qualified service personnel. Servicing is required when the has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the , the has been exposed to rain or moisture, does not operate normally, or has been dropped.
14) Mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
15) The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted candles, should be placed on the .
17) Attention should be drawn to the environmental aspects of battery disposal.
18) The use of in moderate climate.
Television
19) The shall not be exposed to dripping
or splashing and that no objects filled with liquids, such as vases, shall be placed on the .
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Television
Television
Television
;
Television Television
Television
Television
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
Television
Television
The symbol indicates that dangerous voltages constituting a risk of electric shock are present within this unit.
The symbol indicates that there are important operating and maintenance instructions in the literaturaccompanying this unit.
WARNING:
To reduce the risk of fire or electric shock, do not expose this to rain or moisture.Television
WARNING:
The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING: The excessive sound pressure from earphones and headphones can cause hearing loss.
This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Haier is committed to safely recycling electronic products and product materials. Please check for a local recycling location in the United States at: 1800RECYCLING.COM or call 1.800.RECYCLING.
-2-
High voltages are used in the operation of this television receiver. Do not the cabinet. Refer servicing to qualified service personnel.
open
SAFETY AND WARNINGS
Never stand on, lean on, or suddenly push the television or its stand. You should pay special attention to children. Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose the television receiver to rain or moisture.
Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver.
Do not block the ventilation holes on the back cover . Adequate ventilation is essential to prevent failure of electrical components.
of the TV
Do not place your television on an unstable cart, stand, shelf or table. Serious injury to an individual and damage to the television may result if it falls.
/or
When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet.
Avoid exposing the television receiver to direct sunlight and other sources of heat. Do not stand the television receiver directly on other products which give off heat, e.g. video cassette players and audio amplifiers. Do not place naked flame sources, such as lighted candles on
the television. or near
Do not trap the power supply cord under the television receiver s .' stand
If the television is to be built into a compartment or similar enclosure, the minimum distances must be maintained. Heat build-up can reduce the life of your television, and can also be dangerous.
-3-
Dim:515*320mm(
Main features
Integrated ATSC TV tuner for HDTV broadcast reception High brightness provides a vivid and brilliant picture Deeper blacks and brighter whites with high contrast Wide Screen aspect ratio (16:9) for a complete home theater experience HDMI input for true digital connection VGA port for connection to PC Built-in stereo speaker system Full-function Remote Control
Main parameter
INTRODUCTION
Accessories
Accessories
Power Cable.....................................
Infrared Remote Control....................
User s M anual .................................
Battery(AAA)................................... 2
1
1
1
Viewing Picture Size (diagonal)
Resolution:
Power consumption:
Audio Output Power (THD 7%):
Input Power Voltage:
Aspect Ratio:
TV System:
Video Signal System:
Receiving Channel:
High-Definition Multimedia Interface (HDMI) Input
YCb(Pb)Cr(Pr) Input
Composite Video Input
Analog RGB (VGA) Input
Audio Input x 2
Headphone Output
Coaxial Output
USB Input
Horizontal definition (TV line)
32 inches
1920x1080
90W
2x8W
AC 100V-240V 50/60Hz
16:9
ATSC Digital system and NTSC Analog system
NTSC
Cable :1-135/ Air: 2-69 (ATV&DTV)
x 2
x 1
x 1
x 1
x 1
x 1
x 1
Composite Video Input >=350
Video Input >=400
YCb(Pb)Cr(Pr) >=400
-4-
Base Stand Assembly Instruction
1. Attach the base stand neck to the base stand bottom with the included 3 screws.
2. Place the TV with the display side down on a flat surface. Use a cloth or the material from the TV packaging to protect the screen.
3. Place the base stand neck in the slot on the bottom of the TV and push firmly upwards. Attach with the included screw.
-5-
INSTALLATION
Front panel
30 30
1: Remote control sensor.
2: Indicator LED: BLUE POWER ON.
RED STANDBY.
3: Side panel keys
Side panel
3
1
2
1. SOURCE: Display the input source menu.
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or "CH-" to
change the channel up and down. In MENU mode, press "CH+" or "CH-" to select items in standby mode, press "CH+" or "CH-" to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU mode, press "VOL+ " or "VOL- " to adjust the item that you selected.
5. STANDBY: Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to STANDBY.
SOURCE
MENU
CH+
CH-
VOL+
VOL-
STANDBY
1
2
3
4
5
REAR Connections
AC-INPUT 100-240V~50/60Hz
L R
COMPOSITE COMPONENT
Y Pb Pr
VIDEO
All the terminals are (from left to right): POWER SOCKET, VIDEO, AUDIO INPUT, YPbPr INPUT Note: AV and YPbPr share one audio channel.
SIDE Connections
HDMI1HDMI1 HDMI2HDMI2
All the terminals are (from left to right): HDMI1, HDMI2, USB, VGA, HEADPHONE, PC AUDIO, COAXIAL, RF. Note: 1. When HDMI1 has an input signal coming from a DVI source then the audio input signal must be
connected to the PC audio input.
2. When HDMI2 has an input signal coming from a DVI source then the audio input signal must be connected to the YPbPr/AV audio input.
USBUSB
VGA
-6-
HEADPHONERFPC AUDIO
COAXIAL
ANTENNA
Note: Aerial connections: IEC (female). Input impendance:75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are set to Power off.
1.Connect VGA and audio cable.
2.Connect the power cord.
3.Power on the TV, switch to PC mode.
4.Power on the PC. This sequence is very important.
INSTALLATION
HDMI1HDMI1 HDMI2HDMI2
USBUSB
VGA
HEADPHONERFPC AUDIO
-7-
COAXIAL
PC
PRESET MODE
RESOLUTION
1
2
3
4
5
6
7
8
9
10
AC-INPUT 100-240V~50/60Hz
720*400
640*480
640*480
800*600
800*600
1024*768
1024*768
1024*768
1280*1024
1280*1024
INSTALLATION
VIDEO
L R
COMPOSITE COMPONENT
Y Pb Pr
V.Freq.(Hz) H.Freq.(KHz)
70
60
75
60
75
60
70
75
60
75
31.47
31.47
37.50
37.88
46.88
48.36
56.48
60.02
63.98
80.00
-8-
AV EQUIPMENT
You can use the input terminals on TV set rear as follows.
INSTALLATION
HDMI1HDMI1 HDMI2HDMI2
HDMI
VIDEO EQUIPMENT with YPbPr
G
R
B
Y
Yellow (video)
W
White(audio L)
R
Red(audio R or Pr)
B
Blue(Pb)
G
Green(Y)
AC-INPUT 100-240V~50/60Hz
USBUSB
W
R
VIDEO
COMPOSITE COMPONENT
VGA
W
L R
HEADPHONERFPC AUDIO
R
Y Pb Pr
COAXIAL
G
R
B
W R
VIDEO EQUIPMENT
W R
TO AUDIO OUTPUTS
TO VIDEO OUTPUTS
The television's inputs can be connected to the following types of equipment: VCR, multi disc player,
DVD, camcorder, video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i.
-9-
1
27
28
23
19
21
22
16
17
RETURN DISPLAY AUDIO SUBTITLE
MTS/
CC/
GOTO
EPG/
MENU
FAV/
SETUP
ASPECT
REPEAT
CH LIST/
3 8
4
CH
DISPLAY
TV
5
S.M
6
VOL
P.M
7
REMOTE CONTROL
1: POWER To set the TV standby or on.
9
2: NUMBER KEY For direct access to program. 3:
29
Displays the main on-screen menu.
30
4: CURSOR To move within the menu.
25
5: EXIT Used to exit menu.
20
6: VOL+/VOL-
24
To adjust sound level. 7: P.M
26
To switch picture mode.
15
8: Press to display and select the available video sources.
18
9: MUTE To disable or enable the sound. 10: RECALL To access the previously viewed program.
11
11: ENTER Confirms selection. 12: TV DISPLAY Displays/removes the program Information 13: S.M To switch sound mode. 14: CH+/CH­ To access the next or previous Program.
12
15: ASPECT To change picture aspect .
13
16: CH LIST /
Used to display the channel list / Eject or Insert the disc.
17: EPG Display all the information of DTV programs.
14
18: FAV Used to access your favourite channels in digital TV mode. 19: CC Enable or disable the CC function. 20: MTS Switch the sound stereo.
2
10
For a description of the DVD player function buttons on the remote, please refer to page 20 of this manual.
-10-
1. PICTURE MENU
The first item of the MENU is PICTURE MENU.
This menu provides several video adjustment options for fine tuning the video display.
Press to select, press to adjust, press MENU to exit.
Picture Mode: Select the user picture mode (Standard,
1).
Sports, Movie, Custom, Vivid).
2). Brightness: This will adjust the light output of the complete picture, which will mainly affect the dark areas of the picture.
3). Contrast: This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged.
4). Color: This will adjust the saturation level of the colors to suit your personal preference.
5). Tint: Allows you to select color mix (tint) of the picture.
6). Sharpness: This will adjust sharpness of fine details in the picture.
Picture Mode
Contrast
Brightness
Color
Tint
Sharpness
Advanced Video
Adjust
Note: If you want to adjust contrast, brightness, color, and sharpness, the picture mode must to "Custom".
the
Standard
< >
>
Menu
Select
be set
50
50
50
0
50
Exit
Advanced Video: Press to select Advanced Video, press , and
the screen shown below will be displayed.
1). Color Temp: This will adjust color temperature (Cool, Normal, Warm) suit your preference.to
2). Aspect: This will vary the size of the image on the TV screen. There are four modes which can be selected (Wide, Zoom, Cinema and Normal).
3). Noise Reduction: Adjust to reduce the appearance of noise in the picture (dots). There are five modes to choose from (Strong, Auto, Off, Weak and Middle).
OPERATION
2. AUDIO menu
The second item of the MENU is the AUDIO MENU. You can adjust sound here. Press to select, press to adjust, press MENU to exit.
Sound Mode: Select the user sound mode (Standard, News,
1).
Music, Theater, Sports, Custom).
2). Bass: Adjust to increase or decrease lower-pitched sounds.
3). Treble: Adjust to increase or decrease higher-pitched sounds.
4). Balance: Adjust to emphasize left or right speaker balance.
5). Surround: Turn on or off the simulated surround sound feature.
6). AVL: Auto Volume Level, this will the differences in volume level
7). Digital Output: Select the digital sound signal that will output from the coaxial audio output.
8). Audio Language: Select the audio language (English, French, Spanish).
Sound Mode Standard
Bass
Treble
Balance
Surround
AVL
Digital Output PCM
Audio Language English
Note: The Audio language is available for ATSC (DTV) programs.
options
between TV programming.
< >
< > < > < > < >
Adjust
Select
option only
reduce
50 50
Menu
0
Exit
Off Off
3. SETUP MENU
The third item of the MENU is the SETUP MENU. You can here.
set system settings
Press to select, press to adjust, press MENU to exit.
Parental Controls
Timer
Closed Caption
Menu Settings
VGA Settings
Restore Default
> > > > > >
Color Temp. Normal
Aspect Wide
Noise Reduction Middle
Adjust
< > < > < >
Select
Menu
Adjust
Note: Restore Default: Reset all settings to the factory default value. Channel names that have been changed through the option
in the Channel Menu are not reset when a restore default is initiated.
Exit
3.1. Parental Controls:
Press to select , press , and the screen
shown below will be displayed.
Parental Controls
Select
Menu
Exit
-11-
Enter Password ----
Adjust
Input the password, and you will
menu. The factory default password is 0000.
Control
Change password
P.G switch
US
Canada
RRT setting
Reset RRT
Adjust
Menu
Select
enter the Parental
>
Off
< > < > < > < > < >
Menu
Select
Exit
Exit
Change Password: Press , and the screen shown below will be
displayed.
Old password
New password
Confirm password
Adjust
Select
----
----
----
Menu
Exit
1). Old password: Input the old password
2). New password: Input the new password
3). Confirm password: Input the new password again
P.G switch: When the is ON, the options
below
Parental Control shown
can be adjusted.
US: Press , and the screen shown below will be displayed.
OPERATION
1): TV: Press , and the screen
displayed.
Rating Content
Suggested age
ALL
FV
V
S
L
D
Adjust
TV-Y (All children)
TV-Y7(Direct to order children) TV-G(General audience)
TV-PG(Parental Guidance suggested)
TV-14(Parents strongly cautioned)
TV-MA(Mature audience only)
FV (Fantasy violence)
X
Press the ENTER key to lock/unlock .Parental Controls
2). MPAA: switch the movie-rating control level: N/A, G, PG, PG-13, R, NC-17, X.
Rating
G General audiences, All Ages admitted
Parental Guidance suggested. Some material may not be
PG
Suitable for children.
Parents strongly cautioned. Some material .may be
PG-13
Age
Canada: Press , and the screen
displayed.
Inappropriate for children under 13.
Restrict. Under 17 requires accompanying parent or adult
R
guardian (age varies in some jurisdictions).
NC-17
No one 17 and under admitted.
X is an order rating that is unified with NC-17 but may be
X
encoded in the data of older movies.
shown below will be
Select
Content
V
S
(Violence)
(Sexual situation)
X
X
X
X
X
X
Description
shown below will be
Menu
Exit
L (Adult language)
X
X
X
D (Sexually suggestive dialog)
X
X
TV
MPAA N/A
Adjust
> >
< >< >
Select
Menu
Canada English
Canada French
Adjust
Exit
1): Canada English: switch the English-rating control level: EXEMPT, C, C8+, G, PG, 14+, 18+.
-12-
EXEMPT
< >< >
EXEMPT
< >< >
Menu
Select
Exit
OPERATION
Rating
E Exempt: Includes news, sports, documents and other information programming: talk shows, music videos, and variety programming.
C Children: Intended for younger children under the age of 8 years. Pays careful attention to themes that could threaten their sense of securityand well-being.
C8+ Children over 8 years old: Contains no portrayal of violence as the preferred, acceptable, or only way to resolve conflict; nor encourage children to imitate dangerous acts which they may see on the screen .
G General: Considered acceptable for all age groups, Appropriate viewing for the entire family, contains very little violence, physical, verbal or emotional.
PG Parental Guidance: Intended for a general audience, but may not be
Age
suitable for younger children (under the age of 8) because it could contain controversial themes or issues.
14+ Over 14 Years: Could contain themes where violence is one of the dominant elements of the storyline, but it must be integral to the development of plot or character. Language usage could be profane and nudity, present within the context of the theme.
18+ Adults: Intended for viewers 18 years and older and might contain depictions of violence, which while related to the development of plot, character or themes, are intended for adult viewing. Could contain graphic language and portrayals of nudity.
2).Canada French: switch the French-rating control level: E, G,8ANS+,13 ANS+,16ANS+,18ANS+.
Rating
E Exempt programming
G General: All ages and children, contains minimal direct violence, but may be integrated into the plot in a humorous or unrealistic manner .
8ans+ General but inadvisable for young children: May be viewed by a wide public audience, but could contain scenes disturbing to
Age
children under 8 who cannot distinguish between imaginary and real situations. Recommended for viewing with paren . tal guidance
13ans+ Over 13 years: Could contain scenes of frequent violent scenes and intense violence.
16ans+ Over 16 years: Could contain frequent violent scenes and violence.
18ans+ Over 18 years: Only for adult viewing. Could contain frequent violent scenes and extreme violence.
Description
Description
3.2 Timer
You can adjust sleep timer and time related settings here.
Press to select, press to adjust, press MENU to exit.
Sleep timer
Time zone
DST
Clock
Adjust
Off
< >< >
Pacific
< >< >
Off
< >< >
1999/12/31 04:03PM
Menu
Select
Exit
Sleep Timer: You can set the sleep timer.
Note: Time zone, DST and Clock are available in ATSC , and the Clock can't be adjust .
ed
mode
3.3 Closed Caption: switch the closed caption mode.
Press to select Closed Caption, press , and the screen shown below will be displayed.
CC Mode
Basic Selection
Advanced Selection
Option
Adjust
Off
< >< >
CC1
< >< >
Service 1
< >< >
> >
Menu
Select
Exit
RRT setting: in ATSC digital TV mode, it could be adjusted
Reset RRT: Press , and the screen
displayed.
Press¡°ENTER¡±Key To Select
Adjust
Are you sure?
NO
Select
shown below will be
YES
Menu
Exit
1): Advanced selection: only ATSC mode.available in
2): Option: You can edit the closed caption options. Press , and the screen shown below will be displayed.
Mode
Font style Font size Default Font Edge style Default
Font Edge color Default FG color Default BG color Default FG opacity Default
BG opacity Default
Adjust
Custom
< >< >
Default
< >< > < >< > < >< > < >< > < >< > < >< > < >< >
Menu
Select
Exit
NOTE: Only available in ATSC mode.
-13-
3.4 Menu Settings
You can adjust Menu Settings here. Press to select, press to adjust, press MENU to exit.
OPERATION
1). Air/Cable: Select Air TV signal or Cable TV signal.
2). Auto Scan:
should perform a full channel scan in order to capture and store all available channels. Press the to confirm shown below will be displayed.
If it's the first time using the TV, you
, and the screen
Menu Language English
Adjust
3.5 VGA Settings: O nly available in VGA (PC input)
mode.
Press to select VGA Settings, press , and the screen
H-pos
V-pos
Clock
Phase
Auto
Adjust
1). H-Pos: Adjust the horizontal position of the screen.
2). V-Pos: Adjust the vertical position of the screen.
3). Clock: Fine tune the screen width.
4). Phase: Fine tune the phase of the screen. Usually don't adjust this item .
you need to option
5). Auto: Auto adjust to fit the screen.
< >
Menu
Select
shown below will be displayed.
>
Menu
Select
Exit
50
50
50
50
Exit
4. Channel MENU
Here you add/skip TV channels and customize displayed channel info.
Press to select, press to adjust.
Are you sure?
YES
NO
Press¡°ENTER¡±Key To Select
Adjust
Select "YES" and
and the screen
shown below will be displayed,
which indicates that the auto search is progressing.
press the ENTER to confirm,
R F CH: 4 Found: 4 Analog: 1 Digital: 3
Adjust
Select
Select
Menu
Menu
Exit
Exit
3). Favorite: Press to /delete favorite channels.add
4). Show/Hide: Press the ENTER button to display or
hide channels.
5). Channel NO . : Display the current channel number.
Press to change the channel.
6). Channel label: Press to edit the current channel
name.
7). DTV signal: Display DTV signal strength.
Signal strength indicator is for reference only, it
cannot be selected or adjusted.
Air/cable
Auto Scan
Favorite
Show/Hide
Channel NO.
Channel Lable.
DTV signal: Good
Adjust
Air
< >
> > >
2-1
< >
>
Menu
Select
Exit
-14-
OPERATION
5. Multimedia MENU
With an external storage device attached to the USB input, you can use the Multimedia Menu to display JPEG pictures and play MP3 music.
Before starting operation, verify USB storage device is of FAT32 file system format. This television does not support NTFS or other formats. Please use a high-speed USB 2.0 device with a maximum capacity of 50GB.
1. Select a Photo
The screen shown below will be displayed.
USB
Photo Music
..
C:
011.jpg
200812222178878787.jpg
20081.jpg
20087.jpg
20287.jpg
20787.jpg
20087.jpg
20787.jpg
20087.jpg
Total size:3.7 GB 1024 x 768 372.72KB Unused size: 3.7 GB 2006:07:14 15:37:42
Use select the. Jpg files or folders,
press previous
to play, EXIT to stop playing or go to the menu.
2. Select Music
The screen shown below will be displayed.
:17 001/018
C:\photo\
011.jpg
press ENTER
: play
: pause
: stop
: fast backward
: previous
: next
: fast forward
: repeat all
: random play
Random
USB
Photo Music
..
C:
Everything I do.mp3
Sealed With A Kiss.mp3 .mp3 .mp3 .mp3 .mp3 .mp3 .mp3 .mp3
Total size:3.7 GB Unused size: 3.7 GB
Use select the. MP3 files or folders, to play, EXIT to go to menu.
press the previous
:17 001/018
C:\laoge\
Everything I do.mp3
Title:
Artist:
Album:
Year:
Bit Rate: 128kbps
Play 05:49 06:33
press ENTER
Random
-15-
TROUBLE SHOOTING
Trouble phenomenon Symptom
Picture Audio
Snow Noise
Ghost
Interference
Normal Picture
No picture Mute
No color Normal audio Color control
Normal audio
Noise
Mute
Inspection Check
antenna position, direction or connection
antenna position, direction or connection
electronic equipment,car/ motorcycle,fluorescent light
Volume (check if mute is activated or if the audio system connections are not correct)
Power cord is not inserted Power switch is not opened Contrast and brightness/volume setup Press standby key on the remote control for inspecting
Picture breaking up
No color
Normal audio or weak
Noise
Retune channel
TVsystem
The LCD TV panel is built with very high precision technology giving you fine picture details in vibrant color. Occasionally, a few non-active pixels may appear on the screen as a fixed point of red, green, blue, black or white. Please note this does not affect the performance of the product.
-16-
DVD SIDE PANEL
SOURCE
OPEN/CLOSE
PLAY/PAUSE
MPEG4 files on discs
DVD OPERATION
9
Multi-angle
OPEN/CLOSE
PLAY/PAUSE
Disc with its content side (shiny side) facing the front of the unit, insert vertically into the disc tray
How to play a DVD disc
1. Change TV input source to "DVD" mode by pressing button on remote or Source button
on the side of the TV.
2. Place DVD disc in player with the content side
(shiny side) facing the front of the unit.
3. DVD disc will automatically be loaded in to the player
and begin to play.
4. To eject the DVD disc, press Eject/Insert
CH LIST/
button on remote or the button on the side of the unit
Caution
This DVD Player has a Class 1 laser which may be harmful to your eyes. Do not attempt to disassemble the cabinet or make any adjustments. Refer all servicing to a qualified professional.
Features
Disc formats supported by this player:
32
Dolby Digital
KODAK picture CD
MP3 files on CD-R/CD-RW
DVD video
This product incorporates copyright protection technology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macro vision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macro vision Corporation, and is intended for home and other limited viewing uses only. Unless otherwise authorized by Macro vision Corporation. Reverse engineering or disassembly is prohibited.
The product complies with the KODAK Picture CD format and will display KODAK Picture CDs. The "KODAK Picture CD Compatible" logo is a trademark of Eastman Kodak Company and is used with permission.
Subtitle choices
8
Audio choices
LB
16:9
TV Aspect Ratio modes
RESTRICTED
R
Parental Lock
Manufactured under license from Dolby Laboratories."Dolby" and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories, Inc. All rights reserved.
-17-
MENU OPERATION
Press the SETUP button on the remote control, the SETUP MENU will be displayed. After accessing the setup menu, press the direction buttons for up and down movement to select an item desired, and press RIGHT direction button to select the SUBMENU item. Then press the ENTER/OK button to confirm. Press LEFT direction button return to the menu of upper level. To exit the setup, press the SETUP button again. In the SETUP MENU, you may choose any of the following options as you like.
LANGUAGE SETUP Select Language in the setup menu, and display the Language submenu:
DVD OPERATION
SYSTEM SETUP
Aspect Ratio
Select the aspect ratio.
Notes:
The image display ratio is related to the recorded disc format. Some disc can not display images in the aspect ratio you choose. If you play a disc recorded in 4:3 format on a wide screen TV, black bars will appear on the left and right side of the screen. You must adjust the screen setting depending on the type of the television you have.
TV System
Select the different TV system.
Note: The DVD player setting should be matched to your TV set.
refer to the instructions or your TV set.
RATING SETUP
Select Rating in the setup menu, and display the Rating submenu:
For more information of output format,
OSD Language
Use this item to select the language for the setup menu and screen display.
Subtitle
This option provides the preset subtitle language.
MPEG4 Subtitle(optional)
Select different MPEG4 subtitle encoding option.
Note: Not all players support this item.
Audio
Select the built-in disc dubbing language options.
DVD Menu
This option provides the film's menu language options.
VIDEO SETUP Select Video in the setup menu, and display the Video submenu:
desired
Parental Control
Set the parental control feature of the player Note: Password is needed before setting Parental Control.
Set Password Input four digits (password), then press ENTER /Okto confirm.
Note: If you forget your password, please use the universal password 6666 to unlock.
MISC SETUP
Select MISC in the setup menu, and display the submenu:
Use Default Settings
Reset setup data to factory default value.
-18-
DVD OPERATION
MP3/WMA/JPEG PLAYBACK
The MP3/WMA disc has such a directory structure as shown picture above. Press Direction key to choose the root directory and then press ENTER/OK button to enter into the sub directory. Press Direction key to choose the desired track and then press ENTER/OK or PLAY to enjoy the music or movie. If you want to return to the upper menu, press Direction key to choose the icon and press ENTER/OK button.
Filter: Allows selecting the categories of files displayed in the browser list. Repeat: To switch different repeat playing mode Mode: Select different playing mode as follows: Normal: Shuffle mode is cancelled. Shuffle: Shuffle mode enabled. When playback reaches the end of the currentchapter/track, playback jumps to a random chapter/track. As the end of each chapter/track is reached, another random chapter/track will be played until all tracks/chapters have been played or the Shuffle mode is cancelled by toggling to a different Mode Option. Edit Mode: To enable programmed playback mode. When you select the mode, press LEFT Direction key to directory and press ENTER/OK to choose the desired track and press Add to program and press Program view and press the Edit mode to cancel the edit mode. At last press Left key to display program track and press ENTER/OK to start program playback.
Program view: Display program track. Brower view: Display track directory. Add to program: Choice the track press Add to program to add the track of the program play
directory.
Clear program: In the complete stop state(press the STOP button twice), First press Edit mode to enable
the edit mode. Press Left key to program track and press ENTER/OK to cancel the desired track. press Clear program to delete the track of the program play directory.
PICTURE CD PLAYBACK
The PICTURE CD disc has such a directory structure structure as shown in the following picture.
Press Direction key to choose the root directory and then press ENTER/OK button to enter into the sub directory. Press Direction key to choose the desired picture and then press ENTER/OK or PLAY to enjoy the picture. If you want to return to the upper menu, press Direction key to choose the icon and press ENTER/OK button.
Image rotation
In picture play state, press Direction key to rotate the picture.
-19-
DVD OPERATION
Function Buttons
INSERT/EJECT
Eject the disc, press the INSERT/EJECT key; Insert the disc, press the INSERT/EJECT key again. Insert a disc into the DVD player but could not get it to work press the INSERT/EJECT key on the remote or on the TV unit to eject the disc. When a disc is ejecting or is ejected but not take out, press the INSERT/EJECT key on the remote or on the TV unit to insert the disc.
SUBTITLE
Press the button to choose different captions(Requires support from disc)
GOTO
For DVD discs, press the button to choose the desired title and chapter andsearch the desired title time and chapter time.For Super VCD,VCD,CD discs, press this button to search the desired disc time and track time and choose the desired track. Note: During VCD playback, the PBC mode must be set to OFF.
0-9 keys
These keys are used to input the time, as well as title, chapter and track numbers.When a numeric item is displayed on the screen, press the 0-9 keys to select the desired entry, and press ENTER/OK to confirm. When a VCD is playing(with PBC off), press the 0-9 keys to select a track directly.
MENU
During DVD playback, press MENU to display the disc menu of the current title. During VCD/SVCD playback, press MENU to control PBC ON/OFF.
SETUP
Press the button to enter the system setting menu. Press the button again to exit the menu. RETURN When DVD/SVCD/VCD displaying, press RETURN button to the menu(PBC ON only).
DISPLAY
Press the button to show the information of the current playing disc.
ENTER
Press the button to confirm your choice on screen.
REV
During DVD, CD Mp3 or VCD playback, press REV to scan in reverse. The player will review the disc at different times speed. Press PLAY/PAUSE to resume normal playback.
FWD
During DVD, CD,MP3, or VCD playback, press FWD to scan forward.The player will cue the disc at different speed. Press PLAY/PAUSE to resume normal playback.
PREV
During DVD, CD,MP3, or VCD playback, press PREV to play the previous chapter, title or track.
NEXT
During DVD,CD,MP3, or VCD playback, press NEXT toplay the next chapter, title or track.
STOP
Press the button once and the player will be in memory stop state. Continuously press this button twice and the player will be in complete stop state.
Play/Pause
In pause state or stop state, press the button, the player will be in playing state.In play state, press the button the player will be in pause state.
REPEAT
Press to select between different repeat modes Repeat Chapter / Repeat Title / Repeat Off for DVD discs , Repeat Single/ Repeat Folder/All/ Repeat Off(for VCD/CD/MP3 discs)
AUDIO
Changes the audio language or audio channel.
-20-
DVD TROUBLE SHOOTING
If you have any questions, please consult the troubleshooting guide below:
NO PICTURE OR SOUND
Ensure the power button is on.
Ensure the power outlet is operational.
Ensure the power cord is not damaged.
Ensure the power plug is connected
firmly to the outlet.
PICTURE BUT NO SOUND
Ensure the audio is not set to mute.
Ensure you have set the player s AUDIO settings correctly.
POOR PICTURE OR SOUND
Ensure you have set the player s AUDIO settings correctly
Ensure the disc is not scratched or stained.
BAD DISC DISPLAYED
Ensure the disc is not warped, damaged or deformed.
Ensure the disc is not badly stained or damaged.
Ensure the disc format is compatible with the player.
Please check whether you have tried to play a software CD. If so, please restart the player.
REMOTE NOT WORKING
Make sure the Main unit s POWER button is on
Ensure the remote batteries are working.
Point the remote control directly at the player s
IRsensor.
Remove any obstacles between the remote and
theIR sensor.
UNIT NOT WORKING
Turn off the power, and then turn it on again.
NO DISC DISPLAYED
Ensure you have put the disc on the tray.
Ensure the disc is not upside down.
Ensure the disc is not distorted, stained or
scratched.
-21-
WARRANTY
-22-
Loading...