L30CV6-A1
TFT-LCD COLOUR TV
Owner s Manual
30 TFT-LCD TV High Brightness & Contrast NICAM/A2 Stereo Sound
Please read this manual carefully before
using your television and keep this manual
in a good place for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence
of uninsulated magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
CONTENTS
General Precaution..............................................................................................2
Position of keys and plug-ins...............................................................................4
Front panel........................................................................................................4
Back cover interface..........................................................................................4
Function of remote controller...............................................................................5
Precaution for the remote control and the screen...............................................6
Basic operation....................................................................................................7
Switching your television on and off..................................................................7
Programs selecting and volume adjusting.........................................................7
Quick view function............................................................................................7
Mute function.....................................................................................................7
Choosing the language of the display on the screen.........................................7
Menu sections......................................................................................................8
Programs setting up.............................................................................................9
Automatic search
Manual searching
Manual fine tune
Skip the channel ...............................................................................................10
Sound System Select
Adjusting the picture............................................................................................11
Adjusting the picture settings.............................................................................11
Selecting the picture formate.............................................................................12
Adjusting the sound.............................................................................................12
Adjusting the sound
TV set up.............................................................................................................13
OSD tune setting
Signal source setting.........................................................................................13
Changing the picture standard..........................................................................13
Others.................................................................................................................14
Setting the timer................................................................................................14
Auto adjusting function......................................................................................14
Picture still function...........................................................................................14
Teletext function................................................................................................15
External audio and video device connections...................................................17
Connected to PC as a monitor..........................................................................18
Specifications.....................................................................................................19
Troubleshooting guide........................................................................................20
ing...........................................................................................9
...............................................................................................9
................................................................................................10
........................................................................................11
...........................................................................................12
...............................................................................................13
General Precautions
The unit should not be placed in a built-in installation
such as a book-case, limited space rack unless proper
ventilation is provided.
- This may cause fire by overheating or damage the
unit by falling.
Do not use the unit near water, oil or inflammables.
- This may cause a fire.
Do not use a damaged plug and do not let the
power cord touch a heat source.
- This may cause an electric shock or fire.
Do not use the unit in direct sunlight and keep
it away from heaters, stoves, and other sources
of heat.
- This may cause a fire.
During storm conditions (especially when there
is lighting) unplug your TV set from the main
electrical outlet and antenna.
Do not connect too many extension cords or
plugs to an outlet.
- This may cause a fire.
Place the unit on a flat and stable surface.
- The unit can cause injury or damage the unit by falling.
Keep the power adapter away from any heat source.
- This may cause a fire.
Do not attempt to service the unit. Contact an
authorized dealer or repair service.
- Servicing the unit yourself may cause an
electric shock or fire.
If there are any unusual sounds or smells coming
from the unit, unplug it immediately and contact
an authorized dealer or repair service.
General Precautions continued
Do not use or store inflammable substances
near the unit
- This may cause an explosion or fire.
Place the antenna away from the electric wire,
not to touch even though it falls down by wind.
- This may cause an electric shock.
Be sure to plug in tightly and hold the plug,not the
cord when disconnecting the plug from the wall outlet.
- This may cause a fire.
Place the unit away from the wall for well ventilation.
- This may cause a fire.
Do not touch the plug with wet hands.
- This may cause an electric shock.
If an outside antenna is connected to the unit, do not let
the rain water get into the unit by bending or antenna wire
sealing
- This may cause an electric shock or fire.
Unplug the unit from the wall outlet before cleaning.
Use a smooth cloth. Do not use industrial chemicals.
- This may cause an electric shock or fire.
Do not touch the antenna wire and disconnect the
plug from the electrical outlet during storms or lightening.
- This may cause an electric shock or fire.
If the connector between the plug and the pin is dusty or
dirty, clean it. Do not spray detergent directly on the unit.
- This may cause an electric shock or fire.
Disconnect the plug from the outlet if it is not
used for a long period of time.
- This may cause an electric shock or fire.
Function Of Remote Controller
TEXT
MENU
?
INPUT
MUTE
MIX
SUBTITLE
PCCHSTILL
AUTO CLOCK
Q.VIEW/HOLD
I/II
INDEX TIME
POWER
DISPLAY
PIC/SIZE
EXIT
VOL
Buttons and Descriptions
PC input button
switch the signal source to PC
DC power standby button
switch on or standby
Picture still button
Input source switch button
Auto adjustment button(PC status only)
Information display button
Sleep time button
Mute button
Digital button
Quick view button /hold function(text)
Picture Mode Button/size function(text0
I/II A2 and NICAM button
Disappear menu button
Used as the left/right buttons in the OSD
menu screen;used for the adjustment of
volume when the OSD menu is not shown
on the screen.
Used as the up/down buttons in the OSD
menu screen; used for the adjustment of
channel when the OSD menu is not shown
on the screen.
Menu button and used to confirm an action
Channel back and forward buttons
Volume up and down buttons
(The teletext function buttons,refer to
the TELETEXT Application)
Note: The figure of the remote controller
is only for reference.
Preparation For The Remote Control And The Screen
1 Remove the cover of battery
compartment as shown in the figure
2 Properly load one 1.5V Alkaline
battery(AA) 2
of the remote controller.
Do not mix new and used
batteries.
in the compartment
Cautions:
1 Ensure that there is no obstacle
to signals from the remote controller
to the receiving sensor of the
television set.
3 Do not operate the remote
controller directly in floodlight
or strong sunlight.
3 Replace the cover of the battery
compartment.
Do not recharge the
batteries.
2 Keep the remote controller away
from heat source or high moisture
and avoid impacts to the remote
controller.
TV game/PC
If the TV set is used for playing TV games or PC for a long time, permanent shadows will
appear on the screen. Please follow instructions below to avoid such retrieval damages
to the LCD screen.
---Set the brightness and contrast to a lower level;
---Please avoid display a static image on the screen, otherwise a permanent afterimage
will appear on the LCD screen.
---static image, including sign, video game, computer image, teletext, and 4:3 picture
mode;
---The damages of the LCD screen panel below don't belong to the operation bugs,
therefore they are not included within the guarantee;
Caring of the TV cover and the LCD screen panel:
Unplug the power cable from the outlet on the wall, use a soft cloth moistened with
neutral detergent to clean the cover and the screen.
Don't use benzene, alcohol-based or gasoline to clean the TV.
NOTE:
If the environment temperature is much low, the picture will reach the
normal brightness after a period of time. It is not the trouble of the TV (the picture will
reach a normal brightness after a while).
There might be separate brightness or scotomas on the screen, or there might be some
blue, green or red dots which are dead pixels. These won't affect the LCD screen.
Switching Your Television On And Off
Standby set plug the lead into an appropriate socket,
then press the Power Switch button on the back ,and the
red power indicator will light.
PC STILL INPUT POWER
CLOCK
AUTO
MUTE
DISPLAY
Programs Selecting And Volume Adjusting
CH
Quick View Function
Mute Function
VOL
1 If the TV is in the state of standby,press the Power key
on the remote control or on the back panel of the set,then
you can switch standby to on state.
2 Press the Power button again to get into the standby state.
NOTE: If the set is on state, press the Power button, the set
can switch into the standby state.
Press CH / buttons or direct-digit button to select the
program which you favorite.
Press VOL / keys to adust the volume .
Press the Q.VIEW/HOLD key to go back to the channel you
viewed.
1 press MUTE button, a sign will appear of the screen, and
the sound of the set is cut off.
2 In order to recover the sound, press the MUTE button or
VOL / buttons.
Choosing The Language Of The Display On The Screen
Language English
Off
Display the sub menu and select the language item.
1 Press the MENU button to select the Setup sub menu.
2 Press buttons to select the Language item.
3 Press buttons to select the language.
Tint
50
Manual Fine Tune
If the reception is clear, you do not have to fine-tune the channel,
as this is done automatically during the search and store operation.
If however the signal is weak or distorted, you may have to fine-tune
the channel manually.
1 Press MENU button repeatedly to select Ch.
2 Press buttons to select Fine Tune.
3 Press buttons repeatedly to start fine-tune
until the picture and the sound becomes satisfactory.
And press EXIT button to disappear the menu.
Skip The Channel Which You Don't Want
1 Press buttons or direct-digit choosing
button to select a channel you want to skip.
2 Press MENU button continuously to select Ch
Manual Store
ATM
Fine Tune
Add/Erase Off
Sound System D/K
<V->/<V+> key to change
3 Press buttons to select Add/Erase.
4 Press buttons to switch it On.
5 Press EXIT key disappear the menu.
When you select channels with button, this channel
will be skipped, However, you can also use the Direct-digit
Choosing button on the remote control to select this channel
directly.
Note recover the skipped channel
1 Use Direct-Digit Choosing button to select the number of the
channel to be recovered.
2 Press MENU button to select Ch.
3 Press button to select Add/Erase and press
to switch into Off.
Tint
50
Signal Source Setting
The information provided on this page is useful if you find
that some channels have not been stored during the initial
set-up process.
There are some different signal sources in this set, and
you may select the signal source that show up as the following
Language English
Source TV
Osd Tone Off
Size Fill Screen
sequence:
1 Press MENU button repeatedly to select Setup menu.
2 Press button to select Source item.
3 Press button to select the signal source that you
want.
4 Alaso you can select the required signal source by
simply pressing theINPUT or the PC/TV button on the remote
control.
NOTE: In the sub menu, the Source may show up as in the following
sequence:
TV AV SCART AV S-Video SCART RGB YCbCr YPbPr DVI PC
Changing The Picture Size
Language English
Source TV
Osd Tone Off
Size Fill Screen
There are some different signal size in this set, and
you may select the size that show up as the following
sequence: Fill Screen 4:3 Wide Cinema Sub Title.
1 Press MENU button to selectSetup menu.
2 Press button to select Size.
3 Press button to select the size that you want.
Setting The Timer
Using this function. The TV set can be changed into the
standby status after a period of preset time from when
this function is activated.
Press CLOCK button to enter the sub menu then press
button repeatedly and cycle through the preset time
intervals( 0-10-...-180-240 minutes), press MENU button to
active the function
NOTE Press CLOCK button on the remote control If the sleep
timer is set on ,the screen will display. To cancel the sleep
timer function, press the CLOCK button repeatedly and select
0.
Auto Adjusting Function
NOTE this functiong is only available in PC mode.
Press the AUTO button on the remote control to start auto
adjusting the display .
PC STILL
AUTO
PC STILL
AUTO
CLOCK
CLOCK
INPUT POWER
DISPLAY
MUTE
INPUT
POWER
DISPLAY
MUTE
Picture Still Function
Press the STILL button to freeze(or suspend) the current
screen. you may press the STILL button or any other key
again to continue the playing.
NOTE This function is not available in PC DVI YPbPr
mode.
PC
STILL INPUT POWER
CLOCK
AUTO
MUTE
DISPLAY
TELETEXT FUNCTIONS
Teletext is an information system, broadcast by certain channels,
which can be read like a newspaper . It also provides subtitles for
people with hearing difficulties or those who are unfamiliar with the
language in which a particular programme is being broadcast (cable
networks, satellite channels, etc.).
You can press TEXT button into TEXT mode, press again to leave TEXT
mode. All menu related functions are notavailable in TEXT mode. Only a
few direct button control functions are available in TEXT mode, they are:
1 Page up/down
Result:
2 Page number entering
Result:
Use the PRO+/- buttons to browse next or previous page.
To select a teletext page either directly enter the page number
using the numeric button pad on the remote control or use the
PRO+/- buttons, or the coloured Fast Text buttons.
TELETEXT FUNCTIONS
MIX
While in Teletext mode press the MIX button will show the teletext data
superimposed on top of the TV picture. Press the MIX button again to revert
back to Full text.
HOLD
Q.VIEW/HOLDPressing the button will stop the teletext page automatically
updating. This feature is very useful where there are several teletext pages
or data on the same page number.
SIZE
PIC/SIZEPressing the button to change from different screen display size.
This feature is very useful as it magnifies the image making the characters
easier to read.
REVEAL
Pressing the button will reveal hidden text. This feature is used to reveal
information such as answers to Teletext on-line interactive puzzles.
TIME
By entering its 4-digit number to enter a secondary page;While in normal TV
mode only, pressing the button TIME will display the teletext time in the top
right corner for a few seconds.
TEXT
Press the TEXT button on the remote control to turn teletext On/Off.
SUBTITLE
SUBTITLEPressing the button will get the teletext decoder to automatically
search for the subtitle page. In NZ the subtitle is usually page 801.
INDEX
Press the INDEX button to show the list of teletext contents
Fast text coloured buttons
Fast text automatically displays the four most commonly used pages that the
broadcaster thinks that you may want to choose next. Press the same
coloured button on the remote control as the coloured link at the bottom of
the teletext page to go directly to that page.
EXTERNAL AUDIO AND VIDEO DEVICE CONNECTIONS
Some external signal sources, such as VCR, video camera or PC,
can be linked to the television.
ANTENNA INPUT
Connect the CATV or antenna to the
ANT input terminal of TFT-LCD;
NOTE: For better effect of the signal, it is recommended
that you use an outdoor aerial or coaxial cable.
A/V INPUT
1 Connect the audio output terminal of VCD.
to the AUDIO-IN input terminal of LCD TV;
2 Press button to select multi audio mode;
3 Press PLAY button of the VCD and begin to watch.
S-VIDEO INPUT
If we select the S-VIDEO as the signal input terminal
,the picture effect would be better than the (A/V) video input
terminal.
1 Connect the S-VIDEO input terminal of DVD to the
S-VIDEO input terminal of TV
2 Connect the left/right audio output terminal of DVD to
the corresponding terminal
3 Press button repeatedly till you get
4 Press the PLAY button on the DVD player ,and the TV would play
the program of the DVD disk.
INPUT
INPUT S-VIDEO
L
R
S-VIDEO
AUDIOIN
Laser DVD with output terminal
L
AUDIOIN
Laser DVD with output terminal
IN
R
S-VIDEO
IN
VIDEOIN
VIDEOIN
DTV INPUT
1 The chromatism(Y/PbCb/PrCr) terminal connect the
chromatism output terminal of the picture output equipment
such as the DVD,HDTV.and the audio may transfers
through the AUDIO IN terminal.
2 Press the button to select YCbCr mode or the
INPUT
Laser DVD with output terminal
YPbPr mode
3 Press the PLAY button on the equipment to watch the TV.
Headphone port
Plug the headphone in the television headphone port, then the
television program sound will be heard from the headphone, not
by the television speaker. Press VOL+/- buttons to increase or
decrease the sound volume. No sound will be heard if MUTE button
is pressed.
LRL
POWER ANT.
HEADPHONE
PCÂAUDIOIN
AUDIOIN
AUDIOIN
R
L
AUDIOIN
R
SCART
Y Cb/Pb Cr/Pr
S-VIDEO
VIDEOIN
IN
Y Cb/Pb Cr/P r
CONNECTED TO PC AS A MONITOR
VGA INPUT
LRL
POWER ANT.
HEADPHONE
PCÂAUDIOIN
AUDIOIN
R
AUDIOIN
SCART
S-VIDEO
IN
VIDEOIN
Y Cb/Pb Cr/Pr
D-SUB IN DVIIN
To PC AUDIO IN
To D-SUBIN
1 Connect PC VGA output port with television D-SUBIN port.
2 Connect PC audio cable to television PC Audio IN port.
3 Press PC button for PC mode option.
4 Turn on PC and PC images will be displayed on the television screen.
Resolution
Resolution
Horizontal (KHz)
1 When the television temperature is low, initial pictures might flicker a bit.
2 Some red, green and blue spots may appear on the screen.
It is recommended that television screens be set at 1024X768(pixel)/60Hz.3
Vertical (Hz)
DVI input
Press the INPUT button to select DVI mode.
Mode
800x600
1024x768
Vertical
Frequency
(Hz)
60Hz
60Hz
800X600, 1024X768
TROUBLESHOOTING
Verify and try to solve the problems by yourself according to the
instructions specified in the table below before contacting the
after-sales service for technical assistance.
Do not set the television with a still picture for an extended period
as this might result in image residue on the screen. Normal picture
images will be resumed within 12 hours after normal programmes
are displayed.
No picture sound or
No picture/AV mode
Good picture, no
sound or with noise
Excessive brightness Brightness not properly set
Dark image Brightness not properly set
Failed remote control
Obscure or flickering
picture
Television not properly plugged to power socket
Standby mode set (power indicator is red)
Brightness not properly set
Screen not in good condition
No signals received at input port
Sound setup and system not properly set
Mute mode activated
Headphone plugged
Screen not in good condition
Battery out of power
Remote controller in direct sunlight
Weak signals (poor signals or incorrect antenna
direction)
Antenna not properly connected
Overlapped pictures
Unstable pictures
Antenna set to incorrect direction
Electric wave reflection due to mountain or
buildings
Disturbance of auto,hi-voltage main or neon lights
Disturbance of antenna and power input cable
Loading...