Haier L26V6-A8K, L37V6-A8K User Manual

TFT-LCD COLOUR TELEVISION RECEIVER

OWNER'S MANUAL

This User's Manual is applicable for the following models:
L26V6-A8,L26V6-A8K,L32V6-A8,L32V6-A8K,L37V6-A8,L37V6-A8K,
L42V6-A8,L42V6-A8K,L32A9A,L32A9A-A,L32A1A,L32A1A-A

Please READ this manual carefully
before operating the unit, and keep
it for future reference.

*Please read this manual carefully before using your television and keep this
manual in a good place for future reference.

*To achieve the best performance of your television, read this User's Manual
carefully and properly store it for future reference.
*Information of screen displays and figures in the User's Manual may vary due
to technical innovations.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Warning
*To avoid electric hazards, it is strongly suggested that the back cover not be opened, as
there is no any accessory inside the casing.
*If necessary, please contact authorized after-sales services.
*A lighting flash mark in a triangle: A potentially hazardous situation, which, if not avoided,
could result in serious injury by high voltage.
*An exclamation mark in a triangle: Major part or accessory of which technical specifications
must be followed if it is to be replaced.

Warning:
To avoid fire or electric hazards, never place your television
receiver in an area with heavy moisture. Attention should be
paid to avoid accidental scratches or impacts onto the LCD
screen.

Caution:
Unauthorized disassembly of this product is prohibited.

Table of Contents

Safety precautions

.........................................................................................2

Keys and ports

...............................................................................................4

Front control panel

.......................................................................................4

Side AV control panel

...................................................................................5

Rear terminal row

........................................................................................6

Remote controller

...........................................................................................7

Keys of remote controller

...............................................................................8

Operation instructions

Power On/Off

...............................................................................................9

Suspend mode

.............................................................................................9

Menu

............................................................................................................9

Menu exit memory

........................................................................................9

Preset TV program

TV input

......................................................................................................10

Automatic program storage

.......................................................................11

Channel search

..........................................................................................11

Program swap

............................................................................................12

Program edit

...............................................................................................12

Program play

How to select program

...............................................................................13

AV1/AV2/S-Video/YUV/D-SUB/DVI/USB play

Input option

................................................................................................15

Picture quality setup

Picture quality setup

...................................................................................16

Sound adjust

Sound adjust

..............................................................................................18

System setup

System setup

.............................................................................................19

Other functions

Position and phase adjust

.........................................................................21

Timer setup

................................................................................................22

Stream media playing system(only for the models that have the USB functions)

Stream media playing system

........................................................... 23

Connection of external AV devices

...............................................................27

Connected to PC as monitor

.........................................................................28

Specifications

...............................................................................................29

Troubleshooting

............................................................................................30

Note: There is only one AV in L32A9A,L32A1A,L32A9A-A and L32A1A-A, instead of AV1 and AV2 .
That means, all AV1 and AV2 appearing in this manual should be one AV in these four models.

.........

English-1

Safety precautions

The product should be tightly fixed to
avoid drop damages and even fire.

Do not locate the product close to water
or oil, which may cause fire hazards.

Do not use damaged or worn electric
plugs, and keep electric cord away from
heat sources to avoid electric shocks or
fire hazards.

To avoid fire hazards, do not use this
product under direct sunlight or closely
to heat sources.

Unplug the power supply and antenna of
the product when there is a rainstorm,
especially thunderstorm.

Do not connect excessive sockets in
parallel or share the same socket by
multiple plugs to avoid fire hazards.

The product must be placed on a solid
and stable surface to avoid collapse.

Keep the product away from a transformer
or heat source to avoid fire hazards.

Unauthorized disassembly of the television
is prohibited to avoid electric shocks or fire
hazards. Contact authorized after-sales
service if technical service is needed.

Disconnect the product from power supply
and contact authorized after-sales service
if abnormal sound is heard in the product.

English-2

Safety precautions (continued)

Don't use or store inflammable

materials near the product to avoid
explosion or fire hazards.

The antenna of the product should
be away from electric cable to avoid
electric shocks.

Always make sure that the television
is well plugged as poor electric
connection might cause fire.

Unplug the television, use soft fabric,
never chemicals, if you are going to
make cleaning of the product. Make
sure that no water drops in the product.

Don't place the product in a humid area to avoid
fire hazards.

Never touch the plug when your hand is wet
as this might cause electric shocks.

When antenna is used, measures should be
taken to prevent water from flowing down along
the cable into the television.

The plug and electric cable must be kept
clean to avoid electric shocks or fire hazards.

Disconnect the television from power
supply and antenna when there is a
rainstorm or thunderstorm to avoid
electric shocks or fire hazards.

English-3

Disconnect the television from power
supply to avoid electric shocks or fire
hazards in a long vocation.

Front control panel

Keys and ports

MENU

TV/AV

P-

P+

V-

V+

POWER

1
2

3

4

5

MENU TV/AV

P- P+ V- V+

POWER

6

1.MENU: menu display

2.TV/AV: input source select

7

1 2 3 4 5 67

3.P+/- : program plus and minus, menu options

4.V+/V-: volume increase and decrease, menu reset and entry

5.POWER: DC ON/OFF

6.Remote indicator: in red when standby mode

7.Remote control signal receive window

26", 32" and 37" Series(not include L32A9A,L32A1A,L32A9A-A and L32A1A-A)

1.MENU: menu display

2.TV/AV: input source select

3.P+/- : program plus and minus, menu options

4.V+/V-: volume increase and decrease, menu reset and entry

5.POWER: DC ON/OFF

6.USB interface (only for the models that have USB function)

7.Remote indicator: in red when standby mode

8.Remote control signal receive window

English-4

Keys and ports

42" Series

1
2

MENU

3

VOL+

4

VOL-

CH+

5

CH-

TV/AV

6

7

1.Remote control signal receive window

2.Remote indicator: in red when standby mode

3.MENU: menu display

4.VOL+/VOL-: volume increase and decrease, menu reset and entry

5.CH+/CH- : program plus and minus, menu options

6.TV/AV: input source select

7.POWER : DC ON/OFF

Side AV control panel

26", 32" and 37" Series

(Not include L32A9A,L32A1A,L32A9A-A
and L32A1A-A)

Audio R

Audio L

Video

AV IN

(AV2 IN)

English-5

42" Series

USB port
()Only for models that

have USB function

Video

Audio L

Audio R

Power ON/OFF

Plug

VIDEO

L

AUDIO

R

POWER

(AV2 IN)

Keys and ports

Rear terminal row

26", 32" and 37" Series

L

D-SUB IN

DVI IN

YUV L R

YUV IN AUDIO IN

S-VIDEO
IN

L

V

VIDEO IN

AUDIO IN AUDIO IN

1.Power: Power ON/OFF

2.Power input

3.DVI IN: digital RGB input

4.D-SUB IN: computer input

5.YUV (YCbCr,YPbPr) IN: video component input

6.AUDIO IN: external YUV (YCbCr,YPbPr) audio input

7.S-VIDEO IN: S terminal input

8.VIDEO IN: external video input (AV1)

9.AUDIO IN: external S-VIDEO/VIDEO input

10.AUDIO IN: external D-SUB/DVI input

11.Earphone port

12.ANT: antenna input

13.AUDIO OUT: audio output

Note: 1. The sequence of 1.POWER and 2.Power input is as follows ( )
in L32A9A,L32A1A,L32A9A-A and L32A1A-A

2. The 13 AUDIO OUT terminal is only available in models L32A9A and
L32A9A-A

42" Series

R

R

ANT.

AUDIO OUT

L

AUDIO OUT

R

D-SUB IN

DVI IN

YUV L R

YUV IN AUDIO IN

S-VIDEO
IN

V

VIDEO IN

L

L

R

AUDIO IN AUDIO IN

R

1.AUDIO OUT: audio output (to external speaker)

2.DVIIN: digital RGB input

3.D-SUB IN: computer input

4.YUV (YCbCr,YPbPr) IN: video component input

5.AUDIO IN: external YUV (YCbCr,YPbPr) audio input

6.S-VIDEO IN: S terminal input

7.VIDEO IN: external video input (AV1)

8.AUDIO IN: external S-VIDEO/VIDEO input

9.AUDIO IN: external D-SUB/DVI input

10.Earphone port

11.ANT: antenna input

ANT.

English-6

Remote controller

Battery loading

1.Slide open the cover of the battery compartment on the back of
the remote controller.

2.Load two 5# alkaline batteries in the compartment. (plus and
minus poles to respective mark)

3.Replace the cover of the battery compartment.

1

2

3

Precautions

Make sure that there is no
obstacle between the remote
controller and television set.

Keep the remote controller
away from heat source or
humid area to ensure
effective performance of
the remote controller.

As strong light may interfere the
signals, change your position to
operate the remote controller if
the television cannot be turned
on or off as you expect.

Make sure that two 5# 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.

English-7

Keys of remote controller

The remote controller cannot be operated unless the batteries are
properly loaded.

DISPLAY

FAV. POWER

-/--/---

Q.VIEW SLEEP

PSM

TV/AV MUTE

CH+

VOL- VOL+MENU

CH-

UP LEFT

PREV.

DOWN

PAUSE ENTER

SWAP EXIT

NEXT

USB

RIGHT

1.FAV (Favorite)

2.I/II (NICAM)

3.Display
Display ON/OFF

4.Power ON/Standby

5.Digital TV program option

6.USB signal swap

Only for some models

()

7.Q. View (Quickly view)
To former program

8.Sleep
Displaying sleep time, adjustable

by every press

9.Digits
Program direct option

10.PSM (Picture mode option)

11. SSM (Sound mode option)

12.TV/AV swap

13.Mute

14.Program up and down, sound

increase and decrease, menu,
Menu reset

15.Up/down

16.Left/right

17.Prev. (Previous page)

18.Next (Next page)

USB

19.Pause

20.ENTER(Play)

21.Swap

22.Return

Only for the models that
have USB function

Note:
This User's Manual covers the functions of the remote controller, including P+/­(CH+/-), V-/+(VOL-/+), MENU, TV/AV and POWER keys for control of program up,
program down, volume decrease, volume increase, menu, TV/AV and power
ON/OFF.

English-8

Operation instructions

DISPLAY FAV. POWER

-/--/---

Q.VIEW SLEEP

VOL- VOL+MENU

CH+

USB

Suspend mode (ON/OFF)

If Suspend Mode is activated, under TV/AV1/AV2/
S-Video/YUV/D-SUB/DVI/USB status, 5 minutes
later after no signals are input, the television will
enter standby status automatically.

Menu

1.MENU: main menu entry, menu exit or return to
next higher level menu.

2.VOL+: next lower level menu entry.

3.VOL-/+: submenu options.

4.CH+/-: option of next higher/lower level menu.

Power ON/OFF

1.Switch on power supply (indicator in red)

2.If the television screen does not light, press
Power button on the remote controller or the
television.

3.If pause is needed, press Power button on the
remote controller or the television.

4.Disconnect the power supply or unplug the
television if it is intended to completely cease the
television performance.

CH-

English-9

Menu exit memory

When menu parameter is to be modified, the set
picture and sound status and preset program will
be remembered at menu exit.

Preset TV program

TV input

1.Press TV/AV button on television or remote
controller and the menu appears on the screen

( USB only displays on the ). models that have USB function

2.AV1 3.AV2 4.SVideo 5.YUV 6.D-SUB 7.DVI 8.USB1.TV

2.Press digit button 1 to swap to TV input terminal.

3.Press Menu button and then CH+ or CH- button
until the following menu appears on the screen.

TV/AV

CH+

Exchange
Prog. Edit
Search

A

B
C

Auto Search
Change Password

Tuning

Enter

Note:
Password must be entered when operating menu

tuning. The delivery password of this television is

0000.

Please Enter Password

Changing Password

Please Enter New Password

Press digit button on the remote control to enter
the digits.

Please Confirm New Password

VOL- VOL+MENU

CH-

English-10

Preset TV program

Automatic program storage

1.Press CH+/- button on preset menu to select
automatic scan.

2.Press VOL+ button on the remote controller for

CH+

automatic scan of programs with higher level.
The program on desired channel will be saved.

VOL- VOL+MENU

CH-

CH+

VOL- VOL+MENU

Auto Search

BAND VHF-L

FREQ. 188.16 MHz

<MENU>

Prog. 18

Cancel

Channel search

If excessive channel signals of unwanted programs
are received in local area, manual search function
is recommended.
After preset menu appears on the screen, press VOL+
button on the remote controller to enter menu manual
search mode as follows:

Search

BAND VHF-L

FREQ. 188.16 MHz

<MENU>

1.Press CH+/- button to change frequency bands.

2.Press VOL+ or VOL- to scan channel up or down.

Prog. 18

Cancel

CH-

English-11

When a desired television program has been
received by manual scan, the television will cease
scanning automatically and save the program with
current program number. Press the Menu button on
the television or remote controller to return to preset
menu.

Program swap

Press CH+/- button on the remote controller or
television for Exchange in preset menu. Press
VOL+ button to enter the submenu.

Exchange

Current Prog. 010

Exchange Prog. 020

Exchange OK

Program swap

CH+

VOL- VOL+MENU

1. Current program
Press VOL-/+ or digit button on the remote
controller for current program option.

2. Exchange program
Press VOL-/+ or digit button on the remote
controller for the program number to be exchanged.

3. Exchange
After current program and exchange program are
confirmed, select Exchange option and press
VOL+ button to exchange programs (OK on display).

Program edit

Press CH+/- button in preset menu for program
edit. Press VOL+ button to enter the submenu as
follows:

Prog. Edit

Current Prog.

Skip

Prog. Lock

Sound System

Fine Tune - +

OFF

OFF

D/K

CH-

CH+

VOL- VOL+MENU

CH-

Note: Sound system can be adjusted in sequence
of D/K, B/G, M, I, L and Auto.

English-12

Preset program

CH+

VOL- VOL+MENU

CH-

1. Current program
Press VOL-/+ or digit button on the remote controller
for current program option.

2.Skip
If current program number is to be cleared, press
VOL-/+ button to set Skip mode.

3.Program lock
If current program number is to be locked, press
VOL-/+ button to set on Prog. Lock.

4. Sound system
If current program sound is to be changed, press
VOL-/+ button and then the sound system will
change in sequence of Auto D/K B/G M I L.
Note: When channels are being scanned, sound
system will be automatically identified and set
according to television signals. If the sound system
is changed by manual operation, the correct sound
might not be broadcast.

5. Fine tune
If there is abnormal picture or sound in individual
program, press VOL-/+ button to make fine tune until
satisfactory picture and sound are achieved.
After Fine Tune is activated, AFC will be active for
the program, changing the program number into
yellow color. If green color is desired for the program
number, manually scan the same program.

Program play

DISPLAY FAV. POWER

-/--/---

Q.VIEW SLEEP

English-13

USB

How to select program

1.Select desired program

Select buttons in sequence

Press CH+/- button for program option. (Note:
If Skip mode is activated, the program will not
appear.)
Select buttons directly
If program number 1~9 is selected, press digit
1~9 directly.
If two-digit or 3-digit programs are selected,
press -/--/--- button twice or trice. When icon -­or --- appears on the screen, press digit 0~9
program numbers.

If selected channel program is set at Lock on mode and
no password has been entered after initiation of the
television, the screen will indicate require password
entry. If wrong password is entered, channel selection
will fail and previous program will still stay on the screen.
The program locking password can be modified in the
preset menu and previous password will be required.

How to select program (continued)

2. Press VOL+/- button to change sound volume.

3. Press Mute button to silence television sound. If the
same button is pressed again, the sound will resumed.

4. If current program number, color system and sound
system are to be displayed on the screen, press Display
button, and all the related information will appear at
up right corner of the screen. If the Display button is
pressed again, the displayed information will disappear.

5. Sound mode
If the SSM button is pressed again, the sound of
programs will change in following sequence:
Standard News User Music Standard
It is possible for users to select desired sound mode for
different television programs.

Program play

DISPLAY

FAV. POWER

-/--/---

Q.VIEW SLEEP

PSM

USB

6. Picture mode
Press the PSM button on the remote controller, the
picture on the screen will change in sequence as follows
for user's option.
Bright Standard Soft User Bright

7. Off-time
a) Every press of Sleep button, the timer will be set in
the following sequence:
Off 5 15 30 60 90 120 150 180 Off
b) If remaining time of set timer is to be displayed, press
the Sleep button once.

8.NICAM
Press of the I/II button will result in fast swap of NICAM
function (bilingual or stereo) of current program. Under
AV mode, single tune (R or L) and stereo channel can be
selected.

9.Quickly view
Press Q. View button to resume previous program.

10.Fav. Folder
a)Press the shortcut key of Fav. folder until icon is on
display, then current program will be added to the folder.
b)Press the shortcut key to open FAV folder.
c)Press CH+/- button for selection of programs in FAV
folder. Then press VOL+ button to confirm the program.

TV/AV MUTE

CH+

VOL- VOL+MENU

PREV.

CH-

NEXT

RIGHT

UP LEFT

DOWN

PAUSE ENTER

SWAP EXIT

English-14

AV1/AV2/S-Video/YUV/D-SUB/DVI/USB play

Input option

TV/AV

1. Press TV/AV button on the remote controller,
the following menu will appear on the screen.

(USB only displays on the models that have USB funtion)

2.AV1 3.AV2 4.SVideo 5.YUV 6.D-SUB 7.DVI 8.USB1.TV

2. Press the digit button for swap of relative terminal.

English-15

Picture quality setup

Picture quality can be adjusted in any channel.
The picture quality on the screen can be adjusted
as follows:

1.Press Menu button until the following menu
appears on the screen:

TV/AV1//AV2/S-Video menu:
Note: Tint option of Menu will appear only in
NTSC system program.

Picture Mode

User

CH+

VOL- VOL+MENU

CH-

Brightness
Contrast
Color
Sharpness

A

B

Tint

C

Advanced

Picture

YUV YCbCr,YPbPr /USB menu:

User

A

B
C

Picture Mode

Brightness
Contrast
Color
Sharpness

Advanced

Picture

D-SUB menu:

Brightness

Contrast

A

B
C

Color Temp

Red

Green

Blue

Advanced

Picture

User

Enter

Enter

Enter

50
50
50
50
0

50
50
50
50

50

50

50

50

50

English-16

Picture quality adjust

DVI menu:

CH+

VOL- VOL+MENU

CH-

50

50

50

50

50

Enter

A

B
C

Brightness

Contrast

Color Temp

Red

Green

Blue

Picture

User

2. Press VOL+ button to enter Picture menu on which
the current option is in red. Press CH+/- to select desired
item.

3. After one item is designated, press VOL-/+ button to
adjust.

4. Repeat step 2 and 3 until satisfactory picture quality is
achieved. 8 seconds after the latest operation, the menu
disappears from the screen automatically. The menu exit
can also be realized by manual operation.

5. If advanced menu is available, enter the advanced menu
as follows:
TV/AV1/AV2/Svideo/YUV(YCbCr) advanced menu:

Nature

Full

Standard

OFF

Adjust

A

B
C

Picture Advanced

AAA Windows

Display Mode

Color Temp

DNR

English-17

YUV (YpbPr)/USB advanced menu

AAA Windows

Display Mode

Color Temp

A

B
C

Picture Advanced

D-SUB advanced menu

AAA Windows

A

Display Mode

B
C

Picture Advanced

Nature

Full

Standard

Adjust

Nature

Full

Adjust

Sound of television programs can be adjusted in
any channel as follows:

1. Press Menu button and CH+/- button until the
following menu appears on the screen.

Sound adjust

User

50

50

0

OFF

Enter

A

B
C

Sound Mode

Treble

Bass

Balance

Surround

Sound

2. Press VOL+ to enter sound setup menu. Press
CH+/- button for desired option.

3. After your option is designated, press VOL-/+
button to adjust.

4. Repeat step 2 and 3 until satisfactory sound is
achieved. 8 seconds after the latest operation, the
menu disappears from the screen automatically.
The menu exit can also be realized by manual
operation.

Note:

1. Select Balance to balance right and left sound
channels of the television. The intermediate value
is 0. When indication value of Balance increases
toward 50, sound of the right and left speaker
becomes stronger and weaker, respectively. When
indication value of Balance decreases toward -50,
sound of the right and left speaker becomes
weaker and stronger, respectively.

2. The AAA Windows in advanced menu tracks
picture contrast and color to improve the quality of
picture in terms of brightness and sharpness.

3. The advanced menu is displayed on the screen
in various scales for user to select.

CH+

VOL- VOL+MENU

CH-

English-18

System setup

It is possible to select language, OSD transparency,
position and screen display of the menu as follows:

1. Press Menu button once, and the CH+/- button
until the following menu appears on the screen:

TV/AV1//AV2/S-Video:

CH+

VOL- VOL+MENU

CH-

Language

Suspend Mode

Background

OSD Position

A

B
C

OSD Transparency

OSD Stretch

Color System

Set

English

OFF

OFF

Top Left

Opague

OFF

Auto

Enter

YUV YPbPr YCbCr)/USB/D-SUB/DVI

Language

Suspend Mode

Background

OSD Position

A

B
C

OSD Transparency

OSD Stretch

Set

English

OFF

OFF

Top Left

Opague

OFF

Enter

English-19

2. Press VOL+ button on the remote controller to
enter the menu of system setup.

3. Press CH+/- to select desired item on the menu.

4. Press VOL+/- to adjust values level.

OSD language option

Repeat step 3 and 4 to select the language either
Chinese or English.

System setup

Suspend mode

Repeat step 3 and 4 to set on or off Suspend Mode.
5 minutes after the Suspend Mode is set, the
system will enter an energy efficiency status
(standby mode).

Background ON/OFF

Repeat step 3 and 4 to select Background ON/OFF
when no signal appears on the screen.

OSD Position

Repeat step 3 and 4 to locate OSD freely on the
screen for the most desirable position, including
top left , top center , top right , center left , center,
center right , bottom left , bottom center and bottom
right.
Note: OSD Position can only be selected when
OSD Stretch is not intended.

OSD Transparency

Repeat step 3 and 4 to select semi transparency
and opaque background of OSD.

OSD Stretch

Repeat step 3 and 4 for option of OSD Stretch on
or off.

CH+

VOL- VOL+MENU

CH-

Color system option

In TV/AV1/AV2/Svideo mode, repeat step 3 and 4
to set the color system of the front interface among
the options of automatic, PAL, PAL60, NTSC3.58,
NTSC4.43 and SECAM. Automatic mode is usually
set as default.

English-20

Other functions

CH+

VOL- VOL+MENU

CH-

Position and phase adjust

In YUV and D-SUB input mode, H-Position, Phase
and Scope of pictures can be adjusted to eliminate
transverse line interference and decentered picture
as follows:
When YUV/D-SUB input mode is set.

1. Press Menu button on the remote controller and
CH+/- for option of picture position adjust. The
menu display is as follows:

H-Position
V-Position

A

B
C

Phase

50

50

50

CH+

VOL- VOL+MENU

CH-

English-21

Enter

50

50

50

50

Enter

A

B

C

Picture Position

H-Position
V-Position
Phase

Frequency

Auto Adjust

Picture Position

2. Press VOL+ button on television and remote
controller to enter the menu of picture position
setup.

3. Press CH+/- button for desired adjust
parameter option.

4. Press VOL+/- for desired adjust parameter
option until satisfactory value is achieved. When
VGA signals are received, the automatic mode
is used for parameter adjustment. (excluding
HDTV 1080P, 1080i and 720P series)

Other functions

Timer setup

If Off-time, On-time and Remind Time are intended
in TV/AV1/AV2/S-Video/YUV/USB(USB only for the mo

dels that have the function) , follow the instructions as

below:

1. Press Menu button of television and remote
controller, and the CH+/- button for timer setup
menu. The menu display is as follows:

CH+

VOL- VOL+MENU

Clock -- --

OFF Time -- --

ON Time -- --

A

B
C

ON Prog. ---

Remind Time -- --

Remind Prog. -- --

Timer

Enter

2. Before activating timer setup, the clock must be
correctly calibrated or otherwise the timer cannot
be adjusted. If current time setting is cancelled, all
previously set performance of the timer will also be
inactivated.
Note: The timer setup will not affect setup of the
Sleep button and vice versa.

3. Time setup: Press VOL+ button to set minute
and VOL- to set hour.

4. Program setup: Press VOL-/+ button for program
number up and down. It is also possible to press
digit buttons for program number option.

Indication will appear on the screen 10 seconds
prior to expiry of set time.
Suppose off-time is set, and indication is as follows:

CH-

CH+

VOL- VOL+MENU

CH-

OFF TIME 8 S

Note: When the above indication appears on the

screen, set time may be changed if VOL+/- button

is pressed.

English-22

Stream media playing system

The USB port of some models receivers is connected
with the storage device (Note 1) at USB interface
for play of JPEG picture files, MP3 music files and
some format movie files. If TV/AV button of television
and remote controller is pressed, following menu
will appear on the screen:

2.AV1 3.AV2 4.SVideo 5.YUV 6.D-SUB 7.DVI 8.USB1.TV

Press digit 8 button to swap to USB function
interface (as shown in the figure below), or directly
press the USB shortcut button for USB status swap.
Then, connect USB storage device with the USB
port. All the buttons for the interface functions are
located at bottom of the remote controller as shown
in the figure below:

UP LEFT

PREV.

DOWN

PAUSE ENTER

NEXT

RIGHT

English-23

SWAP EXIT

It is possible to press Up or Down button to select
desired JPEG picture, MP3 music or movie, and to
confirm the format of the media files (Note 2) to be
read in the USB storage device.

AAA Multimedia Player

Pic & Music

Movie

Music

Set up

If USB includes two or more than two file system
partitions (Note 3), press Right button to enter the
partitions option mode (as shown in the figure below).
Then press the Right button again to display all
media files of relative formats under current partition
and root directory, and all directory names of relative
files included.

Stream media playing system

AAA Multimedia Player

C

D

Most flash memories and memory cards have one partition.
If Right button is pressed, all media files of relative formats
under current partition and root directory, and all directory
names (as shown in the figure below) of relative files
included will be displayed. Select correct directory name
from the information display window. If the Right button is
pressed again, the sub directory will be entered and all
media files under this directory will be displayed. If Left
button is kept pressed, the directory of next higher level or
main function option mode will be entered. After you move
the cursor to designate your desired files in the table with
the Up, Down, Prev. or Next buttons, press Play button to
play the selected files. Following are further
explanations for four circumstances:

UP LEFT

PREV.

DOWN

PAUSE ENTER

SWAP EXIT

NEXT

RIGHT

AAA Multimedia Player

Pic & music for option of JPEG file
If Pic & Music function is activated, set JPEG picture will
appear in full size on the screen. Press Play button to
scan all pictures automatically. Press of Pause button
will cease automatic scanning. Press Swap button for
scanning mode in 9 pictures. Press Exit button to enter
listed files. Under the 9 picture scanning mode (as shown
in the figure below), press of Up, Down, Left or Right
button to select picture in nine preview windows. Press
Prev. or Next button to view preceding nine pictures and
nine pictures behind. Press Play button to display in full
size currently selected pictures and press Exit button to
enter the listed files.

UP LEFT

PREV.

DOWN

PAUSE ENTER

SWAP EXIT

NEXT

RIGHT

English-24

Stream media playing system

Pic & music for option of MP3 files
If Pic & Music function is activated, MP3 will be played

UP LEFT

PREV.

DOWN

PAUSE ENTER

SWAP EXIT

UP LEFT

DOWN

PREV.

NEXT

NEXT

RIGHT

RIGHT

as background music and, at the same time, automatic
scanning of pictures starts. Press of Pause button will
cease automatic scanning but leave the music being
played. If Play or Pause button is pressed again,
automatic scanning of pictures will be resumed. Press
Swap button for track cycle mode of current background
music. Press Exit button to enter the listed files.

"" Movie for option of avi, dat and mpg files

If Movie function is activated, files of movies (Note 4)
with suffix of avi, dat or mpg will be opened. Press of
Pause button will cease broadcast files. If Play button
is pressed again, the mode will be resumed. Press of
Swap button will indicate the time (Note 5) of the movie
being played. Press Exit button to enter the listed files.

PAUSE ENTER

SWAP EXIT

English-25

Music for option of MP3 files
If Music function is activated, MP3 will be played with
the information (Note 6) of the title, singer, edition, play
time and mode of current MP3 files. Press of Pause will
cease play mode. If Play button is pressed again, the
play mode will be resumed. Press of Up or Down button
will result in playing previous and following music.
Press Swap button to change play mode and press of
Exit button will enter the listed files.

Stream media playing system

If Setup mode is activated, language and display

software version number can be selected. In this mode,

press of Up and Down will result in option of languages.

Press Right button to display version number.

Notes:

1.Supporting equipment

1)Equipment supporting Mass and Storage agreements include
flash memory, mobile hard disk, card reader, some MP3 and
digital camera.2)Equipment supporting PTP agreement includes
some digital camera.3)For mobile hard disk with USB interface,
the first step is to connect the ancillary electric wire of mobile
hard disk to the interface of relative equipment for power supply,
then insert the USB data wire of the hard disk into the product.

2.1)Supporting media: picture, music, MPEG4, MPEG2 and
MPEG1;Supporting file format includes *.AV , *.DIVX, *.MPEG,
*.DAT, *.MP3, *.WHA, *.JPG and *.JPEG. Due to variety of file
coding, it is possible that some files cannot be read.2)If Pic &
Music mode is activated, relative media file format will include
JPEG and MP3 files. After Picture is selected, MP3 files set for
play will open both music and picture files for sync play
performance. As some files must be read while music is being
played, the speed of picture operation response might be
affected.

3.Before starting operation, verify USB storage device is of FAT
32 and FAT file system format. At present, this television does
not support NTFS and the file systems of other format.

4.Many movie files use suffix of avi and mpg. However, many
kinds of format are used for internal files. This television can
only play some avi and mpg files of this format. Those files with
suffix of dat may not be movie files, but data files used by
computers, and cannot be played for movies.

5.Some movie files do not support time display. Press of Swap
might not display play time.

6.Some MP3 files partially include or do not include the
information of the title, singer and edition.

7.External card reader supports most digital cards available in
the market. Readable digital cards are classified according to
the property of card readers , standard mobile hard disks can be
connected (working voltage 5.0V, working current not over
500mA). In the playing process, do not unplug storage
medium or otherwise the television will be halted, files stored
in medium or even USB device damaged. Some time the
television operation may be halted due to excessive rate of
information code errors. In such case, restart the system. As
there are many nonstandard USB mobile devices in the market.
If this kind of USB mobile devices are used in the stream media
play system, the problem of identification failure might occur.
The same problem may also happen with computers, not fault of
televisions.

8.It is suggested that the external devices with USB2.0 interface
be used to improve velocity of information reading and continuity
of information play.

English-26

Connection of external AV devices

Some external signal sources, including VCR, VCD, DVD and PC, can
be connected to the television.

Antenna input

1. Link radio frequency output of VCR to the radio
frequency input on rear side of the LCD television.

2. Link the antenna to the antenna input of VCR.

3. Press TV/AV button for option of television signal
mode.

4. Press Play button on VCR for option of television
programs.

ANT.

AV input

1. Link audio output on VCD to AUDIO IN and VIDEO
IN ports on the television.

2.Press TV/AV button for option of AV1 or AV2 mode.

3.Press Play button on VCD for program play.

S-VIDEO input

If S terminal is used as signal input source, the picture
quality will be better than that by AV input.

1.Link S terminal of DVD to the input of S terminal of
the television.

2. Link the output of left/right sound channels of
Sterminal of DVD to relative port of the television.

3. Press TV/AV button to select S-VIDEO mode.

4. Press Play button on DVD to play the DVD programs
on the television.
Caution: S-VIDEO and AV1 input are multiplexing ports,
which cannot be inserted simultaneously.

DTV input

1. Link the color difference output of some other
equipment, such as DTV, to the YUV (YCbCr, YpbPr)
input terminals of the television. Sound is input by
AUDIO IN.

2. Press TV/AV button to select YUV (YCbCr, YpbPr)
mode.

3. Press Play button on external equipment for program
play.

L

R

AUDIO IN

L

R

AUDIO IN

YUV L R

YUV IN AUDIO IN

S-VIDEO
IN

S-VIDEO
IN

VIDEO IN

VIDEO IN

English-27

Connected to PC as monitor

VGA input

1. Link VGA output port of a PC to the D-SUB IN port of the television.

2. Link audio cable of a PC to AUDIO IN port of television.

3. Press TV/AV button to select D-SUB mode.

4. Turn on the PC and its screen picture will be displayed on the
television screen.
In this way, the television can be used as a PC monitor.

D-SUB IN

R L
AUDIO IN

DVI input

Select digital RGB mode input for DVI input.

Resolution

Mode Resolution

VGA

SVGA

XGA

SXGA

UXGA

640*480 31.5KHz 60Hz

800*600 37.9KHz 60Hz

1024*768 48.4KHz 60Hz

1280*1024

1600*1200 75KHz

63.9KHz

Note: All above listed are subject to VESA Criteria.

Note:
If external audio frequency is input as stereo input (R and L), the I/II
button can be pressed for stereo input mode. If only R or L sound is
input, press I/II button for R or L input mode.

Frame frequency (Hz)Line frequency (Khz)

60Hz

60Hz

English-28

Specifications

Following are some reference specifications, which may vary from
that of the television that you have just purchased due to technical
innovations.

Type

Screen

Viewing angle

Color system

Sound system

Video input

Sound UPO

Power

Standby consumption

Condition

User's Manual

Accessory

Note:Waranty card is only for the special countries and areas.

Model

L26V6-A8
L26V6-A8K

L32V6-A8
L32V6-A8K

L37V6-A8
L37V6-A8K

L42V6-A8
L42V6-A8K

L32A9A
L32A9A-A
L32A1A
L32A1A-A

Remote controller
Power cord
External speaker and fitting (for 42" series only)
Warranty card

Power

Max.140W

Max.160W

Max.180W

Max.240W

Max.160W

Max.160W

2x5W

~ 150-240V 50/60Hz

Working temperature: 0 ~35
Working humidity: 20%-80%
Store temperature: -25 ~45
Store humidity: 5%~90%

Dimensions (including base) (WxHxD)

794mmX514mmX285mm(With stand

940mmX595mmX285mm(With stand

1096mmX683mmX325mm(With stand

1131mmX748mmX338mm(With stand

810mmX610mmX235mm(With stand

807mmX643mmX236mm(With stand

Design and specifications contained in the manual might vary due to
technical innovations.
Sound system L is not available in these series.

English-29

Troubleshooting

Determine and try to solve the problems of your television by yourself before
applying for technical assistance by authorized after-sales service.
Do not leave the television with static picture in an extended period as it may
result in residual image on your television screen. If so happens, set your
television for dynamic operation and normal status will be gained within the
following 12 hours.

Troubleshooting

No picture, no sound

Blank screen

No sound

Poor sound

No picture in some
channel

No color for some channel

program (black and white)

Spots with some or
all pictures

Television out of control

Verify if the television is properly plugged.
Verify if the television is properly supplied power.
Verify if electricity is available.

Verify if correct signals are input.
Press TV/AV button to change signal input to TV input.
Restart the television of power supply is interrupted.

Press Mute button and verify if Mute mode is set.
Switch to other channel and verify if the same problem
happens.
Press VOL+ button to see if the problem can be solved.

Verify if sound system is correct. Refer to some chapter
for adjust.

Verify if correct channel is selected.
Adjust the antenna.
Make adjustments by Fine Tune and Manual Search.

Verify if the same problem exists in other channels.
Check out of picture and sound systems.
Refer to relative instructions in the Manual for color
adjust.

Verify if the antenna is correctly connected.
Verify if the antenna is in good condition.
Make fine adjustment of channel.

Disconnect the television from power supply and, 10
seconds later, connect the television to the power supply.
If the problem still exists, contact authorized after-sales
service for technical assistance.

English-30

07
0090506284