Haier HWM100-828A User Manual
Specification table
Water level/Water
quantity (about)
Water Injection pressure
Washing / spinning capacity
1/23L 2/32L 3/40L 4/49L 5/58L 6/66L 7/76L 8/86L
0.03MPa 1.0MPa
-
10.0kg/10.0kg
Full Automatic W
ashing Machine
User's manual
This manual is for
HWM100-828A
WARRANTY:
Two years free for motor
One year free for other parts
Please read this manual
carefully before using.
Retain it for future reference.
0030508582A
Names of the parts 1
Safety precautions 2
Installation and adjustment 4
Install the water inlet hose 7
Preparation before washing 9
Put in the laundries 10
Usage of the detergent
10
Close the top lid 10
Use the operation button 11
Finish washing 14
Disposal after washing 15
Trouble shooting answer to question 16
Packing list 17
Specification table the back cover
Packing list
User's manual
Components of the water inlet
hose
Bottom plate
Full Automatic
washing machine
One
One
One
One
Inside the document bag
Inside the accessory bag
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
17
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Names of the parts
Phenomena The reason How to settle
The digitron displays E0.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work,
the digital displays E4.
The digitron displays E6.
The machine does
not act
Not wash
Not spin
There's abnormal sound
inside the machine
The water tap leaks
The top lid is opened during reserve procedure.
Is the drain hose put down?
Is the drain hose blocked?
The top lid is not closed.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water level sensor is bad.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Close the top lid.
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Close the top lid.
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales
service department.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
Meaning and description of the symbols
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Common phenomena
Phenomena Explanation
The spinning is intermittent when it starts.
The wash procedure is paused.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
There may be some water flowing out of the
drain hose in the first use of the machine.
Balance the laundries to avoid slanting.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
It is to avoid splashing during water inlet.
It is the water remained in the factory inspection of performance.
16
Forbidden sign
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in damage of
the machine or influence the personal safety of the users.
1
Loading...