Haier HW-07LM03, HW-09LM03-HK, HW-12LM03-HK User Manual

ROOM AIR COMNDITIONER

OPERATION MANUAL

HW07M HW09M HW12M HW18M

Please read this operation manual before using the air conditioner

Please keep it attentively

0010517091

CONTENTS

Safety precautions...................1

Air conditioner operation..........2

Care and Maintenance ............4

Air conditioner installation........5

Troubleshooting.......................7

SAFETY PRECAUTION

Do not install,remove and reinstall the unit yourself.

leakage,electric shock or fire.Please engage an authorized dealer or specialist for the installation work.

The room air conditioner must be earthed. Do not touch or operate with wet hands. Do not turn on the unit by inserting the power plug.Do not switch off the unit by pulling out the power plug.

Do not insert sticks,fingers or other objects into the unit.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. After installation, the power plug should be easily reached.

The wiring method should be in line with the local wiring standard.

OPERATION CONDITIONS

Improper installation may cause

CAUTION

Operation panel

Auto swing switch

HW07M HW09M HW12M

Thermostat switch

This switch controls the preset indoor temperature to make the air conditioner start or stop automatically, so as to reduce power consumption and operate the system both comfortably and economically.

The compressor stops running when the set temperature is reached but the fan continues to operate to keep an even indoor temperature.

CAUTION

Switch off the breaker and set the main control knob to the off position before plugging the power plug into an electrial outlet. In cooling mode, after you turn thermostat switch counter-clockwise,do not turn it back until at least 3 minutes have elapsed.Otherwise, the fuse may blow due to overload. Do not exceed the selection range.

HW18M

Mode selection switch

Applicable ambient temperature range:

Cooling

Max.Temperture:

Min.Temperture:

AIR CONDITIONER OPERATION

Indoor

W.B

D.B D.B

23 C

32 C

18 Co14 C

Outdoor

W.B

43 Co26 C

18 Co/

PART INDENTIFICATION

Machine body

Front panel

Air inlet (indoor side)

Air filter (inside)

Operation

panel

Ventilation

Power plug

Air filter cleaning

When dirt accumulates on air filter, air circulation will be blocked, which causes poor cooling. It is advisable to clean air filter every two weeks for longer operation.

Take out the air filter

1.Press the concave parts on both sides at the lower part of air inlet grille to open the air inlet grille.

2.Hold the hump of filter mesh with fingers (as illustrated) and take it out.

Clean the filter

1.Gently flap the dirt off the air filter.

2.Carefully wash air filter in warm water(below 40°CTo obtain better cleaning effect,soap water or neutral detergent may be used.

3.Flush air filter carefully with clean water after removing dirt.Let it dry completely.

Hump

Air outlet (indoor side)

Machine body

Air inlet

(outdoor side)

CAUTION

Before cleaning, turn off the power Do not raise the front panel any higher than 70° to the unit or damage to the tabs may occur.

D.B :Dry Bulb Temperature

W.B :Wet Bulb Temperature

Ventilation

OPENCLOSE

The ventilation lever must be CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is exhausted.

Airflow Direction

Airflow Direction Vane

The Vertical Airflow Direction Vane is manually controlled by positioning the vane to discharge the air upward,downward or straight out.

Vertical

airflow direction

The horizontal air direction is adjusted by setting the AUTO SWING switch to the ON position.

Note:

It is advisable not to keep horizontal flap at downward position for a long time in COOLor FAN mode,otherwise , condensate water might occur.

Don't move the vertical flap with hand in order to avoid the vertical flap abnormal, using the

AUTO SWING switch to adjust the move of vertical flap.

CARE AND MAINTENANCE

Air filter cleaning

It is advisable to clean air filter every two weeks for longer operation. (You will find how to clean the filter on page 2 .)

Notes

Avoid opening doors and windows unless necessary.

Use curtain or blind Direct sunlight may reduce cooling effect, always use window curtain.

Don't hang clothes in the vicinity of air inlet. This will decrease cooling effect and cause abnormal operation.

Always turn off the air conditioner and the main power supply before clean the unit. Switch off the power supply if the unit is not going to be used for a long period of time.

Cleaning of the

air filter

Don't be exposed to cold air for a long time.

Keep heat source away from air conditioner.

Temperature should be set properly when there are infant,child, the aged or disabled in the room.

Baby has gone sleep, better to adjust suitable temp.

Set temp . a little bit higher before going to bed.

Proper temperature

After unit stops, don't restart it until 3 min. have elapsed.

OK! Enjoy a 3-min nap

Before operating mode selection switch, check that if the air inlet or outlet have been blocked.

AIR CONDITIONER INSTALLATION

SELECTION OF THE INSTALLATION POSITION

1,The air-conditioner is better installed in shadow or in a place with short period of sunshine. In case the air-conditioner is installed at the point exposed directly to the sunshine, it should be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered. (As illustrated in Fig. 1).

2. For the convenience of operation, it is recommended that air-conditioner be installed at least at the height of 760-1300 mm above the floor and no obstacles before it for a free airflow.

3.The shutters at both sides and the top of air-conditioner should be protruded outdoors free from being blocked by wall, window,ect.

4.The back of air-conditioner should be kept over 500mm from the obstacles (for example, wall, etc.) (As illustrated in Fig. 2).

5.To have an efficient drainage, the back part of the air-conditioner should be inclined downward by 5-10mm (As illustrated in Fig. 3).

>500mm

cover

fig.2

(ONLY FOR REFERANCE)

support

INSTALLATION PROCEDURES

1. Fix the prefabricated iron frame to stable position by expansible screws.

2. Put the whole machine with all the accessories installed,

on the iron frame. If there's water outlet flexible pipe, lead it to needed position(see Fig.1).

fig.1

3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to

5-10mm

prevent the entering of outer noise and the leaking of the coolness.

4. After installation of the conditioner, insert the power plug into the outlet and perform test-run.

fig.3

Wall

Water outlet flexible pipe(provide by user)

Fig.1

NOTES:

For longer and trouble-free operation of the unit, pay special attention to the following:

Install air-con at a place strong enough to support the unit. Leave enough space around air inlet and outlet for better circulation. Avoid places where flammable gas leaks. Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blows and hot spring area with sulphurous gas in the air.

THE ENCLOSED ACCESSORIES OF THE CONDITIONER

Name

Figure

Quantity

Rubber lid

11114

Manual

Drain pan

Sealed gasket

PREPARATIONS BEFORE INSTALLATION

Make the wall hole or window hole (see Fig.1)

MODEL A B

HW07M HW09M

HW12M

HW18M

Prepare unit for installation:

370mm 485mm

395mm 615mm

440mm 635mm

Fig. 1

Iron frame

Width of the wall

Screw

Cautions

TROUBLESHOOTING

Phenomenon SolutionCause or check points

Switch on the machine but it does not work immediately.

Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit. Always use at the rated voltage and with specfic air conditioning circuit

Before calling for service.

Check the following points before calling for repairs or service.

If the machine is started after stop,it will need about 3 minutes to re-start so as to prevent the fuse from break.

1.Take out the conditioner and accessories from the package .

2.Disposal of the condensed water.

Install

Drain pan

make the condensed water flow out from the bottom plate. (See Fig.1) If necessary the above method can have extra pipe added on the (available on the market).

to the bottom hole.which can

Drain pan

Cautions

To ensure the safty in transportation, some machines are fixed paper guard by the side of the machine (as figure shows).Please check and remove the paper guard first before you fixed your machine.

Condenser

Fig.1

Bottom plate hole

Drain pan

Paper guard

Screw

Switch on the machine but it does not work.

The cooling effect is not good.

Is plug firmly inserted? Is there power failure?

Does fuse get burned?

Is thermostat switch wrongly adjusted?

Is there any direct sunlight in the room?

Are doors or windows left open?

Are there any obstacles blocking air inlet and outlet?

Is air filter clogged?

Is there too much heat source in the room?

Readjust power supply

Replace fuse.

Readjust the thermostat.

Use curtain or blind.

Shut doors and windows.

Remove the obstacles.

Clean it.

Remove the heat source

If problems can not be solved please pull out power plug and contact your dealer.