Haier HTR13 User Manual

0 (0)

OWNER S MANUAL'OWNER'S MANUAL

ATSC color Television

HTR13 HTR20 HTF20 HTF201

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

CH+

VOL-VOL

CH-

CC SLEEP S.MODE

CH.LIST

ARC

GUIDE

FAV.LIST AUDIOLIST

EXIT

VIDEO

L-AUDIO-R

TV/AV MENU VOL- VOL+ CH- CH+

Before operating the unit, please read this manual thoroughly.

PRECAUTIONS

FCC WARNING-This equipment may generate

or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

LASER SAFETY

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.

LOCATION:INSIDE,NEAR THE DECK MECHANISM.

CONTENTS

Before Operation

Important Safety Instructions............................................................

Installation...........................................................................................

Antenna Connection

..........................................................................

Preparation of the remote control......................................................

Function buttons and ...................................

Front panel of the TV set..................................................................

Rear panel of the TV set....................................................................

Using the remote control...................................................................

The other video and audio equipment .................................................

Antenna connections ...........................................................................

Cable TV connections .........................................................................

Connections the other equipment .......................................................

Basic operation

Setting the language and blue screen .................................................

Channel menu .....................................................................................

Channel selection ................................................................................

Volume adjustment .............................................................................

Screen information ..............................................................................

Video menu ........................................................................................

Manual time setting ............................................................................

Setting the ON/OFF timer ..................................................................

Function menu ...................................................................................

Closed caption ...................................................................................

DTV setup menu ................................................................................

Other function ...................................................................................

Others

Troubleshooting guide

Specifications .....................................................................................

Warranty ............................................................................................

External Connections

........................................................................

1 5 5 5 6 6 7 8 9 10 11 12

13 14 16 17 18 19 21 22 23 28 29 34

36 37 38

IMPORTANT SAFEGUARDS

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol indicates that dangerous voltage constituting a risk of electrical shock is present in this unit.

This symbol indicates there are important operating and maintenance instructions in packaged with this product.

Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure

Product complies with radiation performance standards under the Federal Food, Drug and Cosmetic Act

1. READ THESE INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. KEEP THESE INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED ALL WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW ALL INSTRUCTIONS

All operating and use instructions should be followed.

5.CLEAN ONLY WITH DRY CLOTH.

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning the exterior cabinet only.

6. DO NOT BLOCK ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE

MANUFACTURER`S INSTRUCTIONS.

7. DO NOT USE THIS APPARATUS NEAR WATER

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

PORTABLE CART WARNING

(symbol provided by RETAC)

10. Only use attachments/accessories specified by the manufacturer.

11.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

12. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation, to ensure reliable operation of the unit, and to protect it from overheating.

S3126A

These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the manufacturer`s instructions have been adhered to.

13. POWER SOURCES

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.

Important safety Instructions

14. GROUNDING OR POLARIZATION

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

15. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

16. Unplug this apparatus during lightning storms or when unused for long periods of time.

17. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

18. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

19. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

20. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

21. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

22. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Important safety Instructions

23. DAMAGE REQUIRING SERVICE

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service.

24. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

25. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

26. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

27. DISC SLOT

Keep your fingers well clear of the disc slot as it is closing. It may cause serious personal injury.

28. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

29. SOUND VOLUME

Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage.

30. SOUND DISTORTION

Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.

31. LASER BEAM

Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

32. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

33. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Installation

Antenna connection

If the picture is not clear or is snowy, it is recommended that an External Aerial is used, this is usually mounted outside.

300 twin-lead cable

Antenna adapter

(Not supplied)

75 coaxial cable

Plug

Aerial input

75 standard

coaxial type

(Not supplied)

AC power socket

Note: * It is recommended that a 75 ohm coaxial antenna is used to avoid interference. *To avoid interference from electrical signals, do not bind the antenna cable together with any mains lead.

Preparation for the remote control

Battery installation

Remove the battery cover.

Insert two size AAA batteries matching

the +/-polarities of the battery to the +/marks inside the battery compartment.

Tips for remote operation

!When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries to prevent leakage.

!Do not throw the batteries into fire. Dispose of used batteries in the specified manner.

!Do not drop, dampen or disassemble the remote control.

Front panel the TV set Video 1

HTR13/HTR20/HTF20

L-AUDIO-R

VIDEO

TV/AV

VOL- VOL+ CH- CH+

Parts and functions

VIDEO IN jack

AUDIO IN (L/R) jacks

HTF201

Power Button

Power Indicator and remote receiving window

TV/AV switching

Volume decrease/ increase

TV/AV MENU

V+V- CH- CH+

TV/AV MENU

Input

source

display

Channel down/up

Volume down

V+V-

Volume up

Indicator light

Signal Receiver

CH-

Channel down

Power Switch

CH+

Channel up

Parts and functions

Rear panel of the TV set

HTR13/HTR20/HTF20

Component video input terminal

Y Cb Cr

Video output terminal

Video input terminal

OUT

VIDEO1

L R

AUDIO1

Antenna input socket Audio right channel output terminal Audio left channel output terminal Audio right channel input terminal

Audio left channel input terminal

HTF201

Component video input terminal

Video output terminal

Video input terminal

OUT

VIDEO1

Y Cb Cr

L R

AUDIO1

VIDEO

AUDIO

Video input terminal

Audio left channel output terminal

Audio right channel output terminal

Antenna input socket Audio right channel output terminal Audio left channel output terminal Audio right channel input terminal

Audio left channel input terminal

Remote control

11 12 13

17 18 19 20 21

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

1 2 3

5 6

8 9

TV/DTV

MODE

ARC( Button

Aspect Ratio Control)

(only in 16 9mode)

FAV.LIST Button CH.LIST Button

Q.VIEW Button

INPUT Button SAP Button (only be available

14.

for HTF20,HTF201)

OK Button

15.

MENU Button

16.

17.

SLEEP Button

18.

CC(Closed Caption) Button

19.

GUIDE Button

20.

21.

The other video and audio equipment Connections

You can connect the DVD,VCR and stereo system to the output to enjoy a higher quality of picture and sound effect.

ANT IN

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see the Cable TV connections.

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Connect the 75 ohm cable from the combination VHF/UHF antenna to the RF IN jack.

RF IN

jack

75 ohm coaxial cable

300-75 ohm matching transformer

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

RF IN

jack

300-75 ohm matching transformer

RF IN

jack

If using a flat UHF 300 ohm twin-lead wire, connect these flat wires to an optional 75/300 ohm matching transformer/adapter (available at many retailers), and then connect the adapter to the 'RF' IN connector on the back of the television.

Connect the UHF 300 ohm twin-lead wire to the combiner (not supplied). Connect the VHF 300 ohm twin-lead wire to the 300-75 ohm matching transformer. Attach thetransformer to the combiner, then attach the combiner to the RF IN jack.

Combiner

UHF 300 ohm

VHF 300 ohm

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

RF IN

jack

Combiner

VHF 75 ohm

UHF 300 ohm

Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the combiner. Attach the combiner to the RF IN jack.

Cable TV connections

This unit has an extended tuning range and can tune most cable channels without using a Cable TV Converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE

For basic cable service not requiring a Converter/Descrambler box, connect the 75 ohm Coaxial Cable directly to the RF IN Jack on the back of the unit.

75 ohm coaxial cable

RF IN

jack

FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack of the converter/descrambler box to the RF IN jack on the unit. Follow the connections shown below. Set the unit to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels.

Incoming 75 ohm cable TV cable

Converter/

descrambler

75 ohm cable to

unit

RF IN

jack

FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH SCRAMBLED PREMIUM CHANNELS

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the "B" position, you can directly tune any nonscrambled channels on your unit. With the switch in the "A" position, tune your unit to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to tune scrambled channels.

Incoming 75 ohm cable TV cable

Splitter

Converter/

descrambler

A/B switch

75 ohm cable

to unit

RF IN

jack

Connections to other equipment

Using the audio/video inputs

If you connect the TV to a camcorder or Video Game, you can select different modes by pressing

Press TV/AV repeatedly to select the desired mode.

"AV1", "AV2", "COMPONENT" or TV channel will display on the screen for 4 seconds, no signal will be displayed on the screen when no signal input.

TV/AV.

AV1 AV2 COMPONENT TV Channel

AV 1

To connect the TV to a camcorder

To playback from the camcorder, connect the camcorder to the unit as shown.

Camcorder

VIDEO IN

To Audio/Video OUT

Audio/Video cord (not supplied)

Front of TV

AUDIO IN (R)

AUDIO IN (L)

To connect the TV to a Video Game

The TV can also be used as a display device for many video games. However, due to the wide variety

of formats, they have not all been included in the suggested connection diagram. Youl need to consult

each component's Owner's Manual for additional information.

VIDEO IN

Front of TV

Video Game

To Audio/Video OUT

Audio/Video cord (not supplied)

AUDIO IN (R)

AUDIO IN (L)

Setting the language and blue screen

ou can choose from three different languages (English, French and

Spanish) for the on-screen displays.

SETTING THE LANGUAGE

1 Press POWER ( ) to turn on the TV.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

2 Press MENU, and then

press VOL+/- button to select FUNCTION menu, then press CH- button to enter.

LANGUAGE ENGLISH BLUE SCREEN ON NTSC CAPTION C1 PARENTAL LOCK

FUNCTION

3 Press CH- button to select the LANGUAGE option,

then press VOL+/- to select the desired language: English, Spanish or French.

4 Press MENU until the MENU screen disappears.

SETTING THE BLUE SCREEN

1 Press MENU, and then

press VOL+/- button to select FUNCTION menu, then press CH- button to enter.

LANGUAGE ENGLISH BLUE SCREEN ON NTSC CAPTION C1 PARENTAL LOCK

FUNCTION

0101

2 Press CH+/- button to select the BLUE SCREEN option,

then press VOL+/- to select OFF or ON.

3 Press MENU until the MENU screen disappears.

Channel menu

Here describes the case for searching and memorizing channels for DTV/ATV.

AUTO SCAN (DTV/ATV) (When using antenna) The channels broadcasted in DTV and ATV are

MUTE

Q.VIEW INFO

INPUT TV/DTV

automatically scanned and memorized. Only the receivable channels in the area where this TV is used will be memorized.

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

AUTO SCAN (CATV) (When using basic cable) The channels broadcasted in CATV are automatically scanned and memorized.

NOTE:

Be sure that antenna or cable is connected properly before plugging the power cord.

1 Press MENU, and then press VOL+/- button to select

CHANNEL menu, then press CH- button to enter.

2 Press CH+/- button to

select the RECEPTION option.

SKIP OFF

3 Press VOL +/- button

to select AIR/ CABLE.

RECEPTION AIR AUTO SCAN COLOR SYSTEM AUTO

4 Press CH +/- button

to select AUTO SCAN option.

CHANNEL

Only in analog signal

0101

5 Press VOL+ button to start scanning.

When you press VOL+ on the remote control, scanning the channels in both analog and digital modes will automatically start.

When scanning is completed, the memorized smallest channel will be displayed.

When you press MENU button while scanning, the scanning is interrupted and the memorized smallest channel is displayed.

Channel menu

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CH+

VOL

CH-

SETTING SKIP

After the programs are presetting, you can skip some programs so that to select your favorite channels only.

1 Press MENU, and then

press VOL+/- button to select CHANNEL menu, then press CH- button to enter.

SKIP OFF RECEPTION AIR

2 Press CH+/- button to

AUTO SCAN COLOR SYSTEM AUTO

select the SKIP option, then press VOL+/- button to select ON or OFF.

NOTE: When tuning DTV channels and no signal is present,

the SKIP-over option will be available.

If you want to recover the skipped channel

CHANNEL

0101

CC SLEEP FAV.LIST

CH.LIST

ARC

GUIDE

EXIT

1. Use Direct-digit Choosing button to select the number of the channel to be recovered.

2. Do the above steps again.

3. Press VOL+/- button to set SKIP as Off.

SETTING COLOR SYSTEM(only in ATV mode)

1 Press MENU, and then

press VOL+/- button to select CHANNEL menu, then press CH- button to enter.

2 Press CH+/- button to

select the COLOR SYSTEM option, then

press VOL+/- button to select AUTO or NTSC.

CHANNEL

SKIP OFF RECEPTION AIR AUTO SCAN COLOR SYSTEM AUTO

0101

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

Channel selection

You can select the channel by using either CH +/- button or Channel number buttons. How to select the channel in each way is shown below.

1 Using CH +/- button

Using CH +/- button on the remote control, change the channel. Same operation is available with CH +/- button on the front panel

of the main unit.

Press the Direct Channel selection

Antenna Mode Direct Channel Selection

When the Antenna/Cable menu option is in the Antenna position, all channels

can be instantly selected by using

2-9: Press 2-9 as needed. Example, to select channel 2, press "2". 10-69: Press the 2 digits in order. If you select the channel more than 69,

the channel will not be change, it is no available.

buttons to select the channel.

digits button. For example:

CH+

VOL

CC SLEEP FAV.LIST

GUIDE

EXIT

CH-

ARC

VOL

CH.LIST

CABLE Mode Direct Channel Selection

When the Antenna/Cable menu option is in the Cable position, channels

can be selected as follows:

1-9: Press 1-9 as needed. Example, to select channel 2, press "2". 10-99: Press the 2 digits in order. Example, to select channel 32, press "3" then "2". 100-125: Press the digital 1 button, the "1--" will appear on the screen, then press the 2 digits of remain in order.

VHF 2-13

UHF

14-69

CABLE

VHF 2-13

STD/HRC/IRC

14-36

(A) (W)

37-59

(AA) (WW)

60-85

(AAA) (ZZZ)

86-94

(86) (94)

95-99

(A-5) (A-1)

100-125

(100) (125)

(5A)

NOTE:

In the DTV broadcasting, one channel sometimes broadcasts multiple programs depending on the air time. In this case, the main channel is called major channel and the sub channel is called minor channel.

Volume adjustment

This section describes how to adjust the volume when viewing TV. The MUTE function, which is useful when you have a visitor or a phone call, will be also described.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

1 Using VOL +/- button

You can adjust the audio volume with VOL +/- button on

the remote control.

The volume bar is displayed at the bottom of the screen

when adjusting the volume.

Same operation is available with VOL +/- on the front

panel of the main unit.

2 Using MUTE button

Press MUTE button on the remote control to mute the sound. The colored volume bar is displayed on the screen while muting.

To release the MUTE status, press MUTE button again or press VOL+ button. MUTE will displayed continuously When CC is OFF, MUTE will disappeared 5 seconds later When CC is ON.

SWITCHING AUDIO

This section describes how to switch the audio language in the digital mode.

2 Switch the audio language.

When you press SAP button on the remote control, the currently selected language and the number of received languages will be displayed on the screen.

Every time you press SAP button on the remote control,

the language will be switched.

Languages you can switch differ depending on the

receiving broadcast.

NOTE:

Pressing the SAP button works only with the some TV channels, and does not work with external equipment such as DVD players.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

Screen information

You can display the currently selected channel number or other information such as the audio mode on the screen for checking.

In the analog mode, the currently selected channel number and the audio mode are displayed.

1 Display the channel number and the audio mode.

Press INFO button on the remote control. The currently selected channel number and the audio mode are displayed at the top right of the screen.

AUTO

To clear the display, press INFO button again.

In the digital mode, the detailed information for the currently selected channel such as the program GUIDEe is displayed.

Display the detailed information for the channel. Every time you press INFO button, the display mode will be switched as below.

14.1

DTV-AIR

INFORMATION

ENCODE 17:00-18:30

America Masters

4 5

ENGLISH 1/3 CC

Satchmo: The Life of Lauis

Armstrong A self-taught

9.2

2 3

The following information is displayed in the INFO mode. (1) Program air time (2) Channel number (3) Closed caption (4) Channel title (5) Audio language (6) Program content

NOTES:

When the program guide is displayed in more than 6 lines, use VOL+/-

button and scroll for reading.

"No description provided" is displayed when the program guide is not

provided.

Video menu

SETTING VIDEO

1 Press MENU button. The main menu screen will appear.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

2 Press VOL+/- button to

select VIDEO Option, then press CH- button to enter.

VIDEO

CONTRAST 80 BRIGHTNESS 80 COLOR 50 SHARPNESS 50 TINT 0

0101

3 Press CH+/- to select the desired option, then press

VOL+/- to adjust.

Contrast

This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged.

Brightness

This will adjust the light output of the complete picture, which will mainly affect the darker areas of the picture.

Color

This will adjust the saturation level of the colors to suit your personal preference.

Sharpness

This will adjust the sharpness of fine details in the picture.

Tint

Allows you to select the color mix (Tint) of the picture.

Audio menu

SETTING AUDIO

1 Press MENU button. The main menu screen will appear.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

2 Press VOL+/- button to

select AUDIO Option, then press CH- button to enter.

VOLUME 20

3 Press CH+/- to select

the desired option, then press VOL+/- to adjust.

Volume

This will adjust the sound output level.

0101

AUDIO

Manual time setting

You must set the time manually for ON/OFF Timer.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

EXAMPLE: Setting the time to "8:30 AM"

TO SET TIME

1 Press MENU. The main menu screen will appear.

2 Press VOL+/- button to

select TIME option, then press CH- button to enter the submenu.

TIME --:-- AM TIMER OFF --:-- AM TIMER ON --:-- AM

TIME

3 Press CH+/- button to

select TIME, then press CH+/- button to select "--:--","AM"; press VOL+/- button to set the value & AM &PM.

4 Press MENU until the MENU screen disappears.

0101

NOTE:

After a power failure or disconnection of the power, the

time will get lost. In this case, reset the preset time.

Setting the ON/OFF timer

This feature allows you to have the TV automatically turn on/off at a

predetermined

time. If you program

The ON/OFF TIMER, the TV will turn on/off at the time your predetermined.

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

SETTING THE TIMER ON

1 Press MENU. The main menu screen will appear.

2 Press VOL+/- button to

select TIME option, then press CH- button to enter the submenu.

TIME --:-- AM TIMER OFF --:-- AM TIMER ON --:-- AM

TIME

3 Press CH+/- button to

select TIME ON, then press CH+/- button to select "--:--","AM"; press VOL+/- button to set the value.

4 Press MENU until the MENU screen disappears.

SETTING THE TIMER OFF

1 Press MENU. The main menu screen will appear.

0101

2 Press VOL+/- button to

select TIME option, then press CH- button to enter the submenu.

TIME --:-- AM TIMER OFF --:-- AM TIMER ON --:-- AM

TIME

3 Press CH+/- button to

select TIME OFF, then press CH+/- button to select "--:--","AM"; press VOL+/- button to set the value.

4 Press MENU until the MENU screen disappears.

0101

Function menu

MUTE

Q.VIEW INFO

INPUT TV/DTV

123

456

789

SAP P.MODE

VOL

CC SLEEP FAV.LIST

ARC

GUIDE

EXIT

CH+

VOL

CH-

CH.LIST

SETTING THE NTSC CAPTION

This allows you to configure the way you choose to view the captioning.

1. Press the MENU button and then use VOL+/- button to select the

FUNCTION menu.

Press CH- button to enter,

then p to select NTSC CAPTION.

ress CH+/- button

3.Then use VOL+/- button to

select caption:

C MUTE,TEXT1, TEXT2.

OFF,C1, C2,

FUNCTION

LANGUAGE ENGLISH BLUE SCREEN ON NTSC CAPTION C1 PARENTAL LOCK

0101

You can also press CC button on the remote control to select the desired caption.

4. When you are satisfied with

your choice, press MENU button to return to the previous menu.

CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

+ 56 hidden pages