Haier HT-20216C User Manual

LCD Monitor

User Manual

Model
HT-20216C

• Please read this manual carefully before use.

• The company reserves the right to final interpretation of the instructions.

• Product appearance, please prevail in kind.

• Please keep it with the invoice after reading it.

• In case of product technology or software upgrade, without prior notice

1

2

Table of Contents

Important safety precautions........................3

Product introduction.....................................5

Installation instruction..................................6

Monitor overview.........................................7

Functional operation instructions.................8

Technical Information ................................12

1. Please read all the instructions in this manual in detail and save this
manual for future reference.

2. Observe all cautions and instructions marked on the display.

3. Do not use accessories that are not recommended by the manufacturer, as
this may be dangerous.

4. Do not place the monitor near water, such as a bathtub, washbasin, kitchen
sink, washing machine, wet basement, or swimming pool.

5. Do not place the monitor on an unstable platform or table to prevent the
monitor from falling or hurting the user, or the monitor itself is damaged.
Use only the placement table recommended by the manufacturer or sold with
the monitor. For wall panel or rack mount, please follow the manufacturer's
instructions and use the manufacturer's approved installation tools.

6. The grooves and openings on the cabinet or at the rear and bottom are designed
for ventilation and are also used to ensure the reliability of the machine
and prevent it from overheating. Do not place the monitor on a bed, sofa, rug,
or other similar surface to prevent clogging of the vents. Do not place the
monitor near or on a heat source such as a radiator. Do not place the monitor
in an embedded device unless adequate ventilation is provided.

7. This monitor can only be used with a power supply of the type shown on its
nameplate. If you have questions about the type of power supply you are using,
please consult your monitor dealer or local power supply office.

8. The power cord is the main power supply connection. Do not leave anything on
the power cord. Do not place the power cord in a location where the user
could touch it accidentally.

9. As an additional protection, turn off the power when the monitor is not in
use; when power is off or when the monitor is not in use for a long time,
unplug the power cord from the outlet to prevent the surge from being caused
by the power cord.

10. Do not overload or extend the power cord, otherwise it may cause fire or
electric shock.

11. Do not allow any foreign objects to fall from the casing groove into the
display to prevent fire or electric shock from hitting high voltage points
or shorting the parts. To prevent liquid from splashing onto the display.

12. If the display is faulty, do not open the case. Do not repair the display

by yourself. Please contact Haier Service Center 4006 999 999 for repair.

13. Unplug the monitor from the outlet and contact Haier Service Center for

repair when the following cases happen:
a. The power cord or power plug is damaged or worn out.
b. There is liquid spilled into the display.
c. The display is watered.
d. If the monitor is not working properly according to the instructions,

please adjust only the buttons specified in the instruction manual, because
improper adjustment of other buttons may cause danger and require a lot of
maintenance by the maintenance personnel to restore the machine to normal.

e. The display is dropped or the case is damaged.
f. When the display is obviously abnormal, it indicates that it needs to be

repaired.

14. When replacing parts, make sure that the service personnel use the

replacement components specified by the manufacturer that have the same
performance as the original parts. Unauthorized replacement components may
cause fire, electric shock or other hazards.

15. After the display inspection is completed, the maintenance personnel should

be required to perform routine safety checks to ensure that the display is
in safe operation.

3

Important safety precautions

16. The power outlet should be located near the display or in an easy-to-use
location.

17. The power cord is the primary power outage.

Note: The pictures and icons in this manual are for aesthetic use only and do not show the
actual situation of the product itself.

4

1.1

Product Features

1.2

Packaging and Accessories

After unpacking the carton, please check if your LCD monitor box has the
following accessories:

a, LCD Monitor
b, Power Cord

c, Signal cable

d, User manual

If there is any missing, please contact the dealer from which you purchased.

5

Product Introduction

Microprocessor multi-button OSD menu control
Compatible with IBM standard VGA, extended VGA, super VGA, XGA,
SXGA, WSXGA+, and VESA standard.
Support Windows xp/vista/7/8/10 system

Note:
Please save the carton and packing materials for later use
when moving the monitor.