Haier HSU-36LEA03 User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

PAS24L03-N(T3)
PAS30H03-N(T3)
ASM30H03-N(T3)
HSU-32LEA13-W
HSU-24HEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)
HSU-24LEA03(T3)
HSU-24LEA03-T
HSU-30HEA03(T3)
HSU-30HEA13(T3)
HSU-24LEB03(T3)
HSU-36LEA03(T3)
HSU-18LEB03(T3)
HSU-30LEA13(T3)

Contents

PARTS AND FUNCTIONS

OPERATION

MAINTENANCE

CAUTIONS

TROUBLE SHOOTING

1
2-4

5

6.7
7

HSU-28LEA03(T3)

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010518784

POWER/SOFT

Parts and Functions

Indoor Unit

1

2

3

7

5

4

1

1

Inlet

2

2

Inlet grille

3

3

Air Purifying Filter (inside)

5

4

Outlet

Actual inlet grille may vary from the one shown in the
manual according to the product purchased

8

Display board

3

1

1

Signal receiver hole

HEALTH display

2

(If the unit which you purchased

has healthy function,follow it.

If not,please ignore.)

TIMER OFF display

3

TIMER ON display
SLEEP display

2

5

Horizontal flap

(adjust up and down air flow
Don't adjust it manually)

6

6

Vertical blade

(adjust left and right air flow)

7

Anion generator

4

Ambient temp.display

4

When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.

AUTO display

5

COOL display

6

Dry display

7

HEAT display

8

6

5

7

(inside)

Remote controller

7. MODE button

AUTO COOL DRY FAN HEAT

8. HOUR button

19

4

5

6

8

POWER/SOFT

1.CODE

Used to select CODE A or B with a press,A or B
will be displayed on LCD.

8

Please select A without special explanation.

2.RESET

When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.

3.LIGHT button

Control the lightening and extinguishing of
the indoor LED display board.

4. TIMER button

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.

5. CLOCK button

Used to set correct time.

6. HEALTH button

Used to set healthy operation.

NOTE:

Cooling only unit do not have displays and functions related with heating

If the unit which you purchased has healthy function,follow it.If not,please ignore.

28

30

Loading of the battery

Used to set clock and timer setting.

SWING button

9.

Used to select up or down air sending direction.

. ON/OFF button

10

Used for unit start and stop.

11. TIMER ON display

12. FAN SPEED display

LOW HI

MED AUTO

13. LOCK display

14. SWING UP/DOWN display

15. SLEEP display

16. HEALTH display

17. Operation mode display

AUTO

Operation mode

Remote controller

Display board

18.Signal sending display

19. POWER/SOFT display

20. Left/right air flow display

21. TEMP display

Remote controller: to display the TEMP. setting.

22. TIMER OFF display

23. CLOCK display

24. TEMP button

Used to select your desired temperature.

25. FAN button

Used to select fan speed: LOW,MED, HI, AUTO.

26. HEALTH AIRFLOW button

Used to set the health airflow mode.

27. SLEEP button

Used to select sleep mode.

28. SET button

Used to confirm timer and clock settings.

29. POWER/SOFT button

Use to set power/soft function.

30. LOCK

Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
cancelled and lock condition display disappears.

COOL DRY

HEAT

FAN

Outdoor Unit

OUTLET

INLET

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press

or decrease 1min. If the

change quickly.

"AM "and "PM" stop flashing,while clock starts working.

After time setting is confirmed,press SET,

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

14

will increase

button is kept pressed,time will

Remove the battery cover;

1

2

Load the batteries as

2

illustrated. 2 R-03 batteries,

1

resetting key(cylinder);

3

Load the battery,then put on the cover again.

4

Note:

The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation,

please

remove the batteries and

Hint:

Remove the batteries in case unit won't be in usage for a long period.

If there are any display

after taking-out, just need to press reset key

Be sure that the loading

3

is in line with th

e" + "/"-";

Please change batteries.

reload several minutes later.

1

Operation

Unit start / stop

Press ON/OFF button, unit starts or stops.

Select temp.setting

Operation
Mode

AUTO

COOL

DRY

HEAT

FAN

Display Board

nothing

Remote
Controller

Note

Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
according to room

In DRY mode, when room temperature becomes
lower than temp.setting+2
at LOW speed regardless of FAN setting.

In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.

When FAN is set to AUTO, the

automatically adjusts the fan speed

temperature.

o

C,unit will run intermittently

Auto Operation

According to the automatic
choice system in temperature

in indoors cold or make the
hot movement.

Dry Operation

Note:

In DRY mode, when room
temperature becomes lower

than temp.setting+2 C, unit will

run intermittently at LOW speed regardless of FAN setting.

0

Fan Operation

Cool Operation

Heat Operation

Note:

In HEAT mode,warm air will blow out after a short periodof the time

due to cold-draft prevention function.

When FAN is set to AUTO, the air conditioner automatically adjusts
the fan speed according to room temperature.

Cooling only unit do not have displays and functions related with heating

1.

When FAN is set to AUTO,
the air conditioner
automatically adjusts

the fan speed according

temperature.

to room

2.In FAN operation mode
the unit will not operate

in COOL mode but only
in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled.

AUTO LO MED HI

Air Flow Direction Adjustm

Vertical flap

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

(Auto swing)

Health airflow Operation

The setting of health airflow function

1).Press the button of health airflow, appears
on the display. Avoid the strong airflow blows
direct to the body.

2).Press the button of health airflow again,

appears on the display. Avoid the strong

3.The cancel of the health airflow function
Press the button of health airflow again, both the inlet and outlet grills of the
air conditioner are opened, and the unit goes on working under the condition
before the setting of health airflow function.
After stopping, the outlet grille will close automatically.
Notice: Cannot pull direct the outlet grille by hand. Otherwise,the grille will run
incorrectly. If the grille is not run correctly,stop for a minute and then start,
adjusting by remote controller.

Note:

1 .After setting the health airflow function, the position of inlet and outlet grills is fixed.

2.In heating, it is better to select the mode.

3.In cooling, it is better to select the mode.

4.In cooling and dry, using the air conditioner for a long time under the high air humidity,
a phenomenon falling drips of water occurs at the outlet grille .

5.Select the appropriate fan direction according to the actual conditions.

Remote controller can memorize each operation status. When starting it
next time,just press ON/OFF button and unit will run in previous status.

strong airflow blows direct to the body.

2