Haier HSU-24LEK13, HSU-18LEK13, HSU-12LEK03 User Manual

Installation Manual of Room Air Conditioner

Read this manual before installation
Explain sufficiently the operating means to the user
according to this manual.

Necessary Tools for Installation

1.Driver
cksaw

2.Ha

3.Hole core d

rill

4.Spanner(17,19 and 26mm)

Accessory parts

No. Accessory parts

1

2

3

4

5

6

Remote controller

R-03 d

Mounting plate

Drain hose

Steel nail, cement

4X25

Screw

Plastic cap

ry battery

4X50

Number
of
articles

1

2

1

1

6

4

5.

Torque wrench(17mm,22mm,26mm)

6.Pipe cutter
ring tool

7.Fla
fe

8.Kni

9.Nipper 12.Reamer

10.Gas leakage detector or
soap-and-

water solution

11.Measuring tape

Drawing for the installation of indoor and outdoor units

mc5na

h

ter

Optional parts for piping

Mark

A

B

C

D

E

F

G

Parts name

Non-adhesi

Adhesi

ve tape

Saddle(L.S) with scr

Connecting elect
for indoor and outdoor

Drain hose

Heating insulating material

Piping hole c

ve tape

ric cable

over

ews

m

o

r

e

t

h

a

n

1

0

c

m

om

Attention must be paid to
the rising up of drain hose

m

o

r

e

t

h

a

n

1

0

c

m

A

1

1

4

1

1

10

11

7

8

9

Drain-elbow

Cover

Cushion

Pipe supporting plate

Connecting cable

Note:Cooling only units don't have Drain-elbow

No.0010518787

Arrangement of piping directions

Rear left

Below

Rear
right

Right

Left

m

c

m

o

r

e

t

h

a

n

1

0

c

m

m

c

0

6

n

a

h

t

e

r

o

m

A

The marks from to in the figure are the parts numbers.

G

0

1

n

a

h

t

e

r

o

m

m

o

The distance between the indoor unit and the floor should be
more than 2m.

C

D

E

r

e

t

h

a

n

1

5

c

m

140 140415

Floor fixing dimensions

of the outdoor unit

(Unit:mm)

280

500

140

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

140

256

583

113.5

113.5

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

5.91

3

HSU-09LEK13
HSU-12LEK13
HSU-07LEK03
HSU-07HEK03

HSU-09LEK03
HSU-12LEK03
HSU-09HEK03
HSU-12HEK03

HSU-09LEK03/(DB)
HSU-12LEK03/(DB)

HSU-18LEK13

HSU-108CH09
HSU-138CH09

HSU-12LEK13-M

HSU-24LEK13

Selection of pipe

To this unit, both liquid and gas pipes shall be insulated

as they become Iow temperature in operation.

Use optional parts for piping set or pipes covered with

equivalent insulation material.

Liquid pipe ( )

Gas pipe ( ) 9.52mm(3/8")

For 07 09

6.35mm(1/4")

Indoor unit

1.Fitting of the Mounting Plate and Positioning of the wall Hole

When the mounting plate is first fixed

For 12 18

6.35mm(1/4")

12.7mm(1/2")

For 24

9.52mm(3/8")

15.88mm(5/8")

1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.

3. Find the wall hole location A using a measuring tape

B= 60mm

HSU-12LEK13-M
HSU-09LEK13

HSU-12LEK13
HSU-07LEK03
HSU-07HEK03

HSU-09LEK03/(DB)
HSU-12LEK03/(DB)

HSU-09LEK03
HSU-12LEK03
HSU-09HEK03
HSU-12HEK03

HSU-108CH09
HSU-138CH09

A=145mm

HSU-24LEK13

30mm

HSU-18LEK13

B=

A=145mm

A=145mm

60mm

2.Making a Hole on the Wall and Fitting the Piping Hole Cover

Make a hole of 60 mm in diameter,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation

Indoor side

Wall hole

60mm

Outdoor side

Thickness
of wall

B= 60mm

30mm

30mm

(Section of wall hole)

2

G

Piping hole pipe