Haier HSU-24LEA13-M User Manual

Installation Manual of Room Air Conditioner

Read this manual before installation
Explain sufficiently the operating means to the user
according to this ma

Necessary Tools for Installation

nual.

1.Driver

2.Hacksaw

3.Hole core drill

4.Spanner(17,19 and 26mm)

Accessory parts

No. Accessory parts

1

2

3

4

5

Remote controller

ry battery

R-03 d

Mounting plate

Drain hose

4X50

Steel nail, cement

Number
of
articles

1

2

1

1

6

5.

Torque wrench(17mm,22mm,26mm)

6.Pipe cutter
ring tool

7.Fla
fe

8.Kni

9.Nipper 12.Reamer

10.Gas leakage detector or
soap-and-

water solution

11.Measuring tape

Drawing for the installation of indoor and outdoor units

m
c
5

n
a
h

t
e

r
o

m

m

o

r

e

t

h

a

Optional parts for piping

Ma

rk

Parts name

A

Non-adhesi

Adhesi

B

Saddle(L.S) with scr

C

Connecting elect

D

for indoor and outdoor

E

F

Heating insulating mate

G

ve tape

Drain hose

Piping hole c

ve tape

ews

ric cable

rial

over

n

1

0

c

m

Attention must be paid to
the

rising up of drain hose

m

o

r

e

t

ah

n

01

c

m

A

6

7

8

10

Scr

4X25

ew

Plastic cap

Cover

Cushion

9

Pipe supporting plate

Drain-elbow

No.0010518785

4

1

4

1

Arrangement of piping directions

Rear left

Bel

Rear
right

Right

ow

Left

m

o

r

e

t

h

a

n

1

0

c

m

m

c

0

1

n

a

h

t

e

r

o

m

C

1

D

E

m

o

r

m

c

06

n

a

h

t

e

r

o

m

G

The marks from to in the figure are the parts numbers.

The distance bet

A

ween the indoor unit and the floor should be

more than 2m.

e

t

h

a

n

1

5

c

m

5.913

6.433

583

113.5

113.5

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

PAS24L03-N(T3) HSU-32LEA13-W
HSU-24HEA03(T3)
HSU-24LEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)
HSU-24LEA13-M
HSU-24LEA03
HSU-24HEA03
HSU-28LEA03(T3)

HSU-30LEA03(T3)

HSU-26HEA03
HSU-30HEA03
HSU-24LA2

AMS24H03-N

633

113.5

AMS30H03-N(T3)

HSU-24LEA03-T
HSU-30HEA13(T3)
HSU-30HEA03(T3)

PAS30H03-N(T3)

HSU-36LEA03(T3)
HSU-30LEA13(T3)

HSU-24LEB03(T3)

HSU-24LEA13-M

HSU-24LE03(T3)

HSU-18LEB03(T3)

113.5

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

(microchannel heat-exchanger)

Selection of pipe

To this unit, both liquid and gas pipes shall be insulated

as they become Iow temperature in operation.

Use optional parts for piping set or pipes covered with

equivalent insulation material.

Liquid pipe ( )

Gas pipe ( )

Indoor unit

1.Fitting of the Mounting Plate and Positioning of the wall Hole

HSU-24LE03(T3)

For

HSU-18LEB03(T3)

6.35mm(1/4")

12.7mm(1/2")

For 24K-36K

9.52mm(3/8")

15.88mm(5/8")

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

When the mounting plate is first fixed

1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.

3. Find the wall hole location A using a measuring tape

B= 60mm

mm03

mm03

HSU-24LEA03
HSU-24HEA03
HSU-24LEB03(T3)
HSU-24LEA13-M
HSU-18LEB03(T3)
HSU-26HEA03
HSU-24LA2

A=145mm

B= 60mm

A=145mm

HSU-24LE03(T3)

2.Making a Hole on the Wall and Fitting the Piping Hole Cover

Make a hole of 60 mm in diameter,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation

Indoor side

Wall hole

60mm

(Section of wall hole)

2

Outdoor side

G

Piping hole pipe

Thickness
of wall