Installation Manual of Room Air Conditioner
Read this manual before installation
Explain sufficiently the operating means to the user
according to this ma
Necessary Tools for Installation
nual.
1.Driver
2.Hacksaw
3.Hole core drill
4.Spanner(17,19 and 26mm)
Accessory parts
No. Accessory parts
Remote controller
1
10
2
3
4
5
6
4X25
Scr
7
8
9
ry battery
R-03 d
Mounting plate
Drain hose
Steel nail, cement
ew
4X50
Plastic cap
Cover
Cushion
Pipe supporting plate
Drain-elbow
Number
of
articles
1
2
1
1
6
4
1
4
1
1
5.
Torque wrench(17mm,22mm,26mm)
6.Pipe cutter
ring tool
7.Fla
fe
8.Kni
9.Nipper 12.Reamer
10.Gas leakage detector or
soap-and-
water solution
11.Measuring tape
Drawing for the installation of indoor and outdoor units
m
c
5
n
a
h
t
e
r
o
m
m
o
r
e
t
h
a
rial
Rear
right
Right
n
1
0
c
m
Attention must be paid to
the
rising up of drain hose
om
r
e
t
h
a
n
1
0
c
m
Optional parts for piping
Ma
rk
Parts name
A
Non-adhesi
Adhesi
B
Saddle(L.S) with scr
C
Connecting elect
D
for indoor and outdoor
E
F
Heating insulating mate
G
ve tape
Drain hose
Piping hole c
Arrangement of piping directions
Left
ve tape
ric cable
over
Rear left
Bel
ews
ow
m
o
r
e
t
h
a
n
1
0
c
m
A
C
m
c
0
1
n
a
h
t
e
r
o
m
No.0010518785
m
o
r
m
c
0
6
n
a
h
t
e
r
o
m
G
The marks from to in the figure are the parts numbers.
The distance bet
A
ween the indoor unit and the floor should be
e
t
h
a
n
1
5
more than 2m.
D
E
c
m
Fixing of outdoor unit
Indoor Unit
Selection of Installation Place
Power Source
Selection of pipe
Outdoor Unit
Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally.
When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with nails
or wires in consideration of earthquake and strong wind.
If vibration may a
ffect the house, fix the unit by attaching a vibration-proof mat.
Place, robust not causing vibration, where the body can be supported
su
fficiently.
Place, not a
ffected by heat or steam generated in the vicinity, where
inlet and outlet of the unit are not disturbed.
Place, possible to drain easil
y, where piping can be connected with the
outdoor unit.
Place, where cold air can be spread in a room entirel
y.
Place, nearby a power receptacle, with enough space around. (Refer
to drawings).
Place where the distance of more than lm from televisions, radios,
wireless apparatuses and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the
indoor unit can receive signals when the fluorescent lamps in the room
are lightened.
Place, which is less a
ffected by rain or direct sunlight and is
su
fficiently ventilated.
Place, possible to bear the unit, where vibration and noise are
not increased.
Place, where discharged wind and noise do not cause a
nuisance to the neighbors.
Place, where a distance marked is available as illustrated
in the above figure.
Before inserting power plug into receptacle, check the voltage without fail. The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the powe
r.
A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it.
To this unit, both liquid and gas pipes shall be insulated
as they become Iow temperature in operation.
Use optional parts for piping set or pipes covered with
equivalent insulation material.
2
Liquid pipe ( )
Gas pipe ( )
9.52mm(3/8")
15.88mm(5/8")
For 24 30
HSU-24HEA03(T3)
HSU-24LEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)
HSU-30HEA13(T3)
HSU-30HEA03(T3)
633
113.5
113.5
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
334.6
184.3
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
580
184.3
0
8
3
Indoor unit
Indoor unit
1.Fitting of the Mounting Plate and Positioning of the wall Hole
When the mounting plate is first fixed
1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.
3. Find the wall hole location
A using a measuring tape
B= 60mm
A=145mm
mm03
When the mounting plate is fixed side bar and lintel
Fix to side bar and lintel a mounting ba
the plate to the fixed mounting ba
Refer to the previous article, " When the mounting plate is first fixed ", for the
position of wall hole.
r, Which is separately sold, and then fasten
r.
2.Making a Hole on the Wall and Fitting the Piping Hole Cover
Make a hole of 60 mm in diamete
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation
r,
(Section of wall hole)
Indoor side
Wall hole
60mm
G
Piping hole pipe
Outdoor side
Thickness
of wall
3.Installation of the Indoor Unit
Drawing of pipe
[ Rear piping ]
Draw pipes and the drain hose, then fasten them with the adhesive tape
[ Left Left-rear piping ]
In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear
piping which is marked on heat insulation materials.
3
Indoor unit
1. Insert the drain hose into the dent of heat insulation materials of indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then
connect them.
3. Coat the flaring seal face with refrigerant oil and connect pipes.
Cover the connection part with heat insulation materials closely, and make sure fixing with adhesive tape
Heat insulation
material
Lid for right piping
Lid for under piping
Fix with adhesive tape
Indoor/outdoor electric cable and drain hose must be bound with refrigerant piping by protecting tape.
Lid for left piping
Drain hose
Piping
Indoor/outdoor
electric cable
[Other direction piping]
Cut away, with a nipper, the lid for piping according to the piping direction and then bend the pipe according
to the position of wall hole. When bending, be careful not to crash pipes.
Connect beforehand the indoor/outdoor electric cable, and then pull out the connected to the heat insulation
of connecting part specially.
Fixing the indoor unit body
Hang surely the unit body onto the upper notches of the
mounting plate. Move the body from side to side to verify
its secure fixing.
In order to fix the body onto the mounting plate,hold up
the body aslant from the underside and then put it down
perpendicularly.
mounting plate
Unloading of indoor unit body
When you unload the indoor unit,please use your hand to arise
the body to leave agraffe,then lift the bottom of the body outward
slightly and lift the unit aslant until it leaves the mounting plate.
Easily-demount cleaning of indoor unit
Inlet grille can be taken down
Open the inlet grille,press the button of unlock in the left,then push
it out of the socket and take out the inlet grille.
4
mounting plate
agraffe
Indoor unit
Connecting the indoor/outdoor Electric Cable
Removing the wiring cover
Remove terminal cover at right bottom corner of indoor unit, then
take o
ff wiring cover by removing its screws.
When connecting the cable after installing the indoor unit
1. Insert from outside the room cable into left side of the wall hole, in which
the pipe has already existed.
2. Pull out the cable on the front side, and connect the cable making a loop.
When connecting the cable before installing the indoor unit
Insert the cable from the back side of the unit, then pull it out on the front side.
Loosen the scr
Pull the ca
After the ca
Note
: When connecting the cable, confirm the terminal number of indoor and outdoor units carefully. If wiring
is not correct, proper ope
1. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar
qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW).
2. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.
3. The wiring method should be in line with the local wiring standard.
4. After installation, the power plug should be easily reached.
A breaker should be incorporated into fixed wiring. The breaker should be all-pole switch and the
5.
distance between its two contacts should be not less than 3mm.
ews and insert the cable ends fully into terminal block, then tighten the screws.
ble slightly to make sure the cables have been properly inserted and tightened.
ble connection, never fail to fasten the connected cable with the wiring cover.
ration can not be carried out and will cause defect.
5
3 4
2
1
Indoor unit
HSU-24LEA03(T3)
HSU-24LEA13(T3)
3 4 5
1 2
POWER
SUPPLY
Indoor unit
connecting wiring:
HSU-24LEA03(T3)
HSU-24LEA13(T3)
Power cable:
POWER
SUPPLY
Y/G
BR
BL
Y/G
Outdoor unit
BR
BL
4G0.75m
3G2.5mm
1
2
3
L
N
1
2
3
4
5
6 7
Outdoor unit
5
4
3
2
1
Indoor unit
Indoor unit
HSU-24HEA13(T3)
5
4
3
2
1
HSU-24HEA03(T3)
POWER
SUPPLY
5
POWER
SUPPLY
BR
BL
Y/G
BR
BL
Y/G
Outdoor unit
1
2 3
4 5
6 7
L
N
1
2
3
4
5
6
(
N)
7
(
L
)
Outdoor unit
5
4
3
2
1
Indoor unit
HSU-30HEA13(T3)
HSU-30HEA03(T3)
connecting wiring:
HSU-24HEA03(T3)
HSU-24HEA13(T3)
HSU-30HEA13(T3)
HSU-30HEA03(T3)
Power cable:
POWER
SUPPLY
Outdoor unit
BR
BL
Y/G
6G0.75m
3G2.5mm
L
N
Outdoor unit
Outdoor unit
1.Installation of Outdoor Unit
Dr
Install according to
2.Connection of pipes
To bend a pipe, give the roundness as large as possible not to crush the pipe
Connecting the pipe of gas side first ma
The max
vertical distance between the indoor unit and the outdoor unit is 5 m.
Half union
awing for the installation of indoor and outdoor units
kes working easier.
Flare
nut
Forced fastening without careful centering
may damage the threads and cause a
leakage of ga
s.
Pipe Diameter ( )
Liquid side 9.52mm(3/8")
Spanner
Torque wrench
Be careful that matters, such as wastes of sands, etc. shall not enter the pipe.
Gas side 15.88mm(5/8")
Fastening torque
40N.m
60N.m
3.Connection
Use the same method on indoor unit
rminal block, then tighten the screws.
te
rt the cable according to terminal number in the same manner as the indoor unit.
Inse
If wi
ring is not correct, proper operation can not be carried out and controller may be damaged.
Fix the ca
4.Atta
If the drain-elbow is used, please attach it as
figure. (Note: Only for heat pump unit.)
ble with a clamp.
ching Drain-Elbow
. Loosen the screws on terminal block and insert the plugs fully into
6
Outdoor unit
5.Purging Method:
Push the air out of the indoor unit
and piping as followes:
(1) Remove the valve cap on 2-way valve in outdoor unit.
(2) Loosen by 1/2 turn the flare nut of gas pipe, which is
is conneted to 3-way valve.
(3) Loosen 2-way valve by 90
o
using hexagon wrench,
and after approx.10 sec tighten it up. Gas comes out
through flare nut on wide pipe. If no gas is discharged,
tighten flare nut with specified torque.
(4) Open 2-way and 3-way valves using specified torque.
(5)
Tighten the caps on the valves with specified torque.
Tighten torque N.m
Valve rod
Valve cap
7-9
20-25
When connecting pipe exceeds 5 meters, 60g refrigerant shall be added per
exceeding meter. Charge according to the following list.
for 24k 30k
Piping length
Additional amount
5m 7m
No need
120g
10m
300g
HSU-24HEA03(T3)
HSU-24LEA03(T3)
HSU-24HEA13(T3)
HSU-24LEA13(T3)
2-way valve
9.52mm(3/8")
2-way valve
9.52mm(3/8")
3-
way valve
15.88mm(5/8")
3-
way valve
15.88mm(5/8")
HSU-30HEA13(T3)
HSU-30HEA03(T3)
20m
900g
Outdoor unit
A
B
CAUTION
In case more than 5 metres，oil trap
should be installed every 5~7m.
C
Oil trap
Indoor unit
C
Outdoor unit
Indoor unit
A
B
A
Indoor unit
Max.Elevation:B=10m
Max. Length:A=20m
B
Outdoor unit
Note: When extending piping, air inside piping shall be removed by using external refrigerant gas,
charge according to the following list.Brand new outdoor unit is charged 80g more refrigerant than
regulated weight. Only for first installation, this extra 80g can be used to purge air in pipes.
During this procedure, 80g
refrigerant will be discharged piping.
(This must be strictly controlled within 90o and 10 sec.)
7
1.Power Source Installation
The power source must be exclusively used for air conditioner. (Over I0A)
In the case of installing an air conditioner in a moist plac
rth leakage breaker.
ea
For installation in other places, use a circuit breaker as far as possible.
e, please install an
2.Cutting and Flaring
Pipe cutting is car
After inse
rting the flare nut, flaring work is carried out.
A
ried out with a pipe cutter and burs must be removed.
Flare tooling die
Correct
Lean Damage of flare Crack Partial Too outside
3.On Drain
Please install the d
Please don't do the d
age
rain hose so as to be downward slope without fail.
rainage as shown below.
Work of Piping
Liquid side
Gas side
Incorrect
Pipe diameter( )
9.52mm(3/8")
15.88mm(5/8")
Size A(mm)
1.0~1.8
1.4~2.2
It becomes high midway.
Please pour
ried out surely to outdoor.
car
The end is immersed
water.
in
water in the drain pan of the indoor unit, and confirm that drainage is
In case that the attached d
to it without
Please kindly
fail.
ck for Installation and Test Run
Che
explain to our customers how to operate through the instruction manual.
Check Items for Test Run
Gas leak from pipe connecting?
Heat insulation of pipe connecting?
Are the connecting wi
indoor and outdoor fi
to the te
rminal block?
Is the connecting wi
and outdoor fi
rings of
rmly inserted
ring of indoor
rmly fixed?
Less than 5cm
It
waves. The gap with the ground
is too small
There is the bad smell
from a ditch
rain hose is in a room, please apply heat insulation
Put che
ck mark in boxes
Is d
rainage securely carried out?
Is the ea
rth line securely
connected?
Is the indoor unit securely fi
Is p
ower source voltage abided
by the code?
Is there a
ny noise?
xed?
Is the lamp no
Are cooling and heating (when
in heat pump) per
Is the ope
regulator no
rmally lighting?
formed normally?
ration of room temperature
rmal?
8
Loading...