Haier HSU-24HEK03, HSU-12LEK13-M, HSU-18HEK03 User Manual
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-07LEK03
HSU-09LEK03
HSU-12LEK03
HSU-09LEK13
HSU-12LEK13
HSU-07HEK03
HSU-09HEK03
HSU-12HEK03
HSU-18LEK13
HSU-24LEK13
HSU-12LEK13-M
HSU-18HEK03
HSU-24HEK03
Contents
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
CAUTIONS
TROUBLE SHOOTING
1
2-4
5
6.7
7
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
0010518786
Parts and Functions
TIMER
CLOCK
SET
SLEEP
Indoor Unit
1
2
3
4
5
5
6
1
1
Inlet
2
2
Inlet grille
4
5
Anion generator
6
6
Vertical blade
adjust left and right air flow
7
Power indicator
Timer mode indicator
8
(Lights up whenTimer operation is selected.)
9
Operation mode indicator
(lights up when the compressor is on.)
10
Remote signal receiver
(A beeping sound is generated when a signal
from remote controller isreceived.)
11
Ambient temp display
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
is displayed and this room temperature is only for reference.
Horizontal flap
12
adjust up and down air flow Don't adjust it manually
3
3
Air Purifying Filter (inside)
5
4
Outlet
(inside)
(Lights up when unit starts.)
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
7
8
9
10
11
12
Remote controller
1
2
5
3
23
13
18
12
21
19
17
1. Mode display
HEALTH
TIMER
CLOCK
SET
LOCK
ON/OFF
FAN
MODE
SWING
SLEEP
RESET
AUTO
COOL
DRY
HEAT
2. SWING display
3. FAN SPEED display
4. SLEEP display
5. LOCK display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.
FAN
LO MED HIAUTO
10
6. SIGNAL SENDING
6
7. TIMER OFF display
7
8. TIMER ON display
8
9. CLOCK display
9
10. TEMP display
4
11. POWER ON/OFF
11
15
20
14
16
22
Used for unit start and stop.
12. MODE
Used to select AUTO run, COOL,
DRY,HEAT and FAN operation.
13. FAN
Used to select fan speed LO,
MED, HI, AUTO
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD display.
18. TEMP.SETTING
Used to select your desired temp.
19. SET /
Used to confirm timer and clock
settings.
20. TIMER
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
21. CLOCK
22. RESET
Used to reset the controller back
to normal condition.
23. HEALTH
Used to operate the healthy function
and LCD display.
unacailable on some models.)
LIGHT
Used to set correct time
(This function is
Outdoor Unit
OUTLET
INLET
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the
change quickly.
"AM "and "PM" stop flashing,while clock starts working.
After time setting is confirmed,press SET,
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
14
will increase
button is kept pressed,time will
Loading of the battery
Remove the battery cover;
1
2
3
Load the battery,then put on the cover again.
4
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
ries have been used up.
batte
If the remote controller can't run normally during operation,
remove the batteries and
please
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display
Load the batteries as
2
illustrated. 2 R-03 batteries,
1
resetting key(cylinder);
Be sure that the loading
3
is in line with th
Please change batteries.
reload several minutes later.
after taking-out, just need to press reset key
e" + "/"-";
1
Operation
Unit start / stop
Press ON/OFF button, unit starts or stops.
HEALTH
ON/OFF
FAN
Operation
Mode
AUTO
COOL
DRY
HEAT
FAN
Select temp.setting
Remote
Controller
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
according to room
In DRY mode, when room temperature becomes
lower than temp.setting+2
at LOW speed regardless of FAN setting.
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
automatically adjusts the fan speed
Note
When FAN is set to AUTO, the
temperature.
FAN
MODE
SWING
o
C,unit will run intermittently
Auto Operation
According to the automatic choice
system in temperature in indoors
cold or make the hot movement
Dry Operation
FAN
MODE
SWING
FAN
MODE
SWING
Cool Operation
FAN
MODE
SWING
Heat Operation
Note:
In DRY mode, when room temperature becomes lower than temp.
setting+2 C, unit will run intermittently at LOW speed regardless
of FAN setting.
o
Fan Operation
1.
When FAN is set to AUTO,
the air conditioner
automatically adjusts
the fan speed according
temperature.
to room
2.In FAN operation mode
the unit will not operate
in COOL mode but only
AUTO LO MED HI
HEALTH
ON/OFF
FAN
MODE
in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled.
Air Flow Direction Adjustm
(1)
FAN
FAN
MODE
SWING
Note:
In HEAT mode,warm air will blow out after a short periodof the time
due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically adjusts
the fan speed according to room temperature.
Cooling only unit do not have displays and functions related with heating
MODE
SWING
Remote controller can memorize each operation status. When starting it
next time,just press ON/OFF button and unit will run in previous status.
2
Loading...