Haier HSU-09RE03/R2, HSU-18RE03/R2, HSU-12RE03-R2, ORS-CGJW22HM1-H, HSU-22RE03/R2 User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-07RE03/R2 HSU-09RE03/R2 HSU-12RE03/R2 HSU-18RE03/R2 HSU-22RE03/R2

No, 0010562726

Contents

Cautions Parts and functions Operation

Maintenance Trouble shooting

2 3-5

6-14 15-16

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Indoor

Cooling

Outdoor

Indoor

Heating

Outdoor

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

4. The distance between the indoor unit and the floor should be more than 2m.

5. The wiring method should be in line with the local wiring standard.

6. After installation, the power plug should be easily reached.

7. The waste battery should be disposed properly.

8. The appliance is not intended to use by young children or infirm persons without supervision.

9.Young children should be supervised ensure that they do not play with the appliance.

10.The appliance must be installed on strong enough supporter.

11.The wiring diagram is attached inside the machine.

Maximum: D.B / W.B 32oC/23oC Minimum: D.B / W.B

Maximum: D.B Minimum: D.B Maximum: D.B

Minimum: D.B Maximum: D.B / W.B Minimum: D.B / W.B

18oC/14oC 43oC/26oC

18oC 27oC

15oC 24oC/18oC

-7oC/-8oC

Parts and Functions

Indoor Unit

Inlet grille

Air filter

Test running switch(manual)

Used only for test running in cooling when room temp. is below 16oC. Don't use it in normal operation.

Emergency switch(manual)

Used when remote controller is lost or defective. Unit will run temporarily.

Remote signal receiver

A beeping sound is generated when a signal from remote controller is received.

Vertical flap

Use remote controller to adjust up and down air flow. (Don't adjust it manually.)

Power indicator

Lights up when unit starts.

Timer mode indicator

Lights up when Timer operation is selected.

Operation mode indicator

Lights up during compressor running.

Actual inlet grille may vary from the one shown in the manual according to the product purchased

Outdoor Unit

HSU-07RE03/R2 HSU-09RE03/R2 HSU-12RE03/R2

OUTLET

INLET

HSU-18RE03/R2 HSU-22RE03/R2

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Parts and Functions

Operation

2 3

Clock set

A U T O

ON/OFF

MODE SET

FAN

SWING

SLEEP

LOCK RESET

TEMP

TIMER

CLOCK

Buttons and display of the remote controller.

1. Mode display AUTO

COOL DRY HEAT FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL, DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

Used to reset the controller back to

normal condition.

ON OFF

5 6

LO MED HIAUTO

When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.

NOTE: Cooling only unit do not have displays and functions related with heating

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

Parts and Functions

Operation

Buttons and display of the remote controller.

If the unit which you purchased has healthy function, Remote controller should like the following figure:

2 3

1. Mode display AUTO

COOL DRY

HEAT

FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

ON/OFF TEMP

MODE SET

FAN TIMER

SWING CLOCK

SLEEP

LOCK RESET

A U T

HEALTH

OFF

6 7

LO MED HIAUTO

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL, DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

Used to reset the controller back to

normal condition.

23. HEALTH

Used to set healthy operation

24. HEALTH

display

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.

NOTE: Cooling only unit do not have displays and functions related with heating

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

+ 12 hidden pages