Haier HSU-22LE04, HSU-12LE04, HSU-09LE04, HSU-18LE04 User Manual
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
FJT-12L
FJT-18L
FJT-24L
HSU-07LD03
HSU-09LE04
HSU-12LE04
HSU-18LE04
HSU-22LE04
Please read this operation manual before using the air conditioner.
0010511927
Cautions
The machine is adaptive in following situation
I. Applicable ambient temperature range:
Indoor
Cooling
Outdoor
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similar qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW).
3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.
4. The distance between the indoor unit and the floor should be more than 2m.
5. The wiring method should be in line with the local wiring standard.
6. After installation, the power plug should be easily reached.
7. The waste battery should be disposed properly.
8. The appliance is not intended to use by young children or infirm persons without supervision.
9.Young children should be supervised ensure that they do not play with the appliance.
10.The appliance must be installed on strong enough supporter.
11.The wiring diagram is attached inside the machine.
Maximum: D.B / W.B
Minimum: D.B / W.B
Maximum: D.B/ W.B
Minimum: D.B
32oC/23oC
18oC/14oC
43oC/26oC
18oC
1
Parts and Functions
Indoor Unit
Inlet grille
Air filter
Horizontal flap
Use remote controller to
adjust up and down air flow.
(Don't adjust it manually.)
Power indicator
Lights up when unit starts.
Timer mode indicator
Lights up when Timer operation
is selected.
Test running switch(manual)
Used only for test running in cooling
when room temp. is below 16oC.
Don't use it in normal operation.
Emergency switch(manual)
Used when remote controller is lost or
defective. Unit will run temporarily.
Remote signal receiver
A beeping sound is generated when
a signal from remote controller is
received.
Operation mode indicator
Lights up during compressor
running.
Actual inlet grille may vary from the one shown in the manual according to
the product purchased
For 22k unit, the power plug is on the outdoor unit
Outdoor Unit
HSU-09LE04
HSU-07LD03
FJT-12L
OUTLET
INLET
HSU-12LE04
HSU-18LE04
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
FJT-18L
FJT-24L
HSU-22LE04
2
Parts and Functions
Operation
1
2
3
4
5
12
13
14
15
16
17
18
Clock set
ON/OFF
MODE SET
FAN
SWING
SLEEP
LOCK RESET
A
U
T
O
HEALTH
AM
o
PM
C
TEMP
TIMER
CLOCK
ON OFF
Buttons and display of the remote controller.
1. Mode display
AUTO
COOL
DRY
6
7
8
9
10
11
19
20
21
22
24
23
FAN
2. SWING display
3. FAN SPEED display
4. HEALTH display
5. SLEEP display
6. LOCK display
7. SIGNAL SENDING display
8. TIMER OFF display
9. TIMER ON display
10. CLOCK display
11. TEMP display
12. POWER ON/OFF
Used for unit start and stop.
13. MODE
Used to select AUTO run, COOL,
DRY and FAN operation
14. FAN
Used to select fan speed LO, MED, HI, AUTO
15. HOUR
Used to set clock and timer setting.
16. SWING
Used to set auto fan direction.
17. SLEEP
Used to select sleep mode.
18. LOCK
Used to lock buttons and LCD
display.
19. TEMP.
Used to select your desired temp.
20. SET
Used to confirm timer and clock settings.
21. TIMER
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF
22. CLOCK
Used to set correct time
23. RESET
Used to reset the controller back to
normal condition.
24. HEALTH
Used to operate the healthy function
When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.
NOTE: Cooling only unit do not have displays and functions related with heating
LO MED HIAUTO
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
3
Parts and Functions
Operation
Buttons and display of the remote controller.
If the unit which you purchased has not healthy function, Remote controller should
like the following figure:
12
13
14
15
17
16
1
2
3
A
U
T
O
ON OFF
AM
o
PM
C
4
ON/OFF
11
MODE SET
FAN
SWING
SLEEP
LOCK RESET
TEMP
TIMER
CLOCK
5
6
7
8
9
10
18
19
20
21
22
Clock set
When unit is started for the first time and after replacing batteries in remote controlle
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickl
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.
1. Mode display
AUTO
COOL
DRY
FAN
2. SWING display
3. FAN SPEED display
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
8. TIMER ON display
9. CLOCK display
10. TEMP display
11. POWER ON/OFF
Used for unit start and stop.
12. MODE
Used to select AUTO run, COOL,
DRY and FAN operation
13. FAN
Used to select fan speed LO, MED, HI, AUTO
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD
display.
18. TEMP.
Used to select your desired temp.
19. SET
Used to confirm timer and clock settings.
20. TIMER
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF
21. CLOCK
Used to set correct time
22. RESET
Used to reset the controller back to
normal condition.
LO MED HIAUTO
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
4
Loading...