Haier HSU12XHK, HSU09XHK Operational Manual

SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL

Contents

HSU09XHK
HSU12XHK

PARTS AND FUNCTIONS
OPERATION
MAINTENANCE

CAUTIONS

TROUBLE SHOOTING

1
2

5
6

7

●

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

001053

Parts and Functions

Indoor Unit

1

2

3

4

5

1

Inlet

2

Inlet grille

3

Outlet

4

Vertical blade

(adjust left and

5

Horizontal flap

right air flow)

6

7

8

(adjust up and down air flow.

Don't adjust it manually)

Please be subject to the actual produce purchased the
above picture is just from your reference

8

6

7

Display board

Emergency

Switch

Air Purifying Filter

(inside)

Remote controller

1

2

3

4

5

9

10

11

12

13

14

15

16
17

1. Mode display

Operation mode

Remote controller

AUTO FANCOOL DRY

2. Signal sending display

3. SWING display

4. FAN SPEED display

LO MED HI

5. LOCK display

6. TIMER OFF display
TIMER ON display

7.TEMP display

HEAT

Display
circulated

AUTO

8

Additional functions display

.

6

Operation mode

Remote controller

7

9. QUIET button

QUITE

SLEEP

Supplemented
electrical
heating

HEALTH

10. HEAT button

11. COOL button

12. AUTO button

8

13. FAN button

14. TIMER button

18

15. HEALTH button

16. LOCK button

19

Used to lock buttons and LCD display.

20

17. LIGHT button

Control the lightening and extinguishing
of the indoor LED display board.

21

18. POWER ON/OFF button

19. DRY button

22

20. TEMP button

21. SWING button

23

22. HOUR button

24

23. EXTRA FUNCTION button

Function: Air sending--- Healthy
airflow position1--- Healthy airflow

25

position 2 --- Restore the original
flap position --- Right & left air airflow

--- A-B yard---10 and heating symbol
displayed simultaneously--- Sleeping

--- Electrical heating--- Refresh air

reserved function) --- Power ---

(
Fahrenheit/Celsius mode conversion

24.CANCEL/CONFIRM button
Function: Setting and cancel to the

timer and other additional functions.

25. RESET button

When the remote controller
appears abnormal, use a sharp

pointed article to press this button
to reset the remote

POWER

Outdoor Unit

4

OUTLET

INLET

Please be subject to the actual produce purchased the
above picture is just from your reference

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

4

Healthy function is not available for some units.

Loading of the battery

Remove the battery cover;

1

2

3

Load the battery,then put on the cover again.

4

Note:

The distance from the remote to the receiver should be less than
23 feet (7 meters) with no obstructions.

Fluorescent lights or cordless telephones will reduce the range
of the remote.

If the display is dim the remote batteries may need to be replaced.

Remote malfunctions can sometimes be corrected by removing
the batteries for a few minutes and then replacing them.

Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.

Load the batteries as illustrated.

2

2 AAA batteries, resetting key

1

(cylinder);

Be sure battery polarity is

3

correct

" + "/"-";

1

Operation

Base Operation

Remote controller

3

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2. Select operation mode

COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode

3.Select temp.setting

Press

/

Every time the button is pressed, temp.setting
increase 1
rapidly

Every time the button is pressed, temp.setting
decrease 1
decrease rapidly

Select a desired temperature.

button

o

C,if kept depressed, it will increase

o

C,if kept depressed, it will

4.Fan speed selection

Press FAN button. For each press, fan speed

changes as
Remote controller:

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

follows:

LOW

MED HI

1

2

4

3

Display

circulated

AUTO

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.

When the emergency operation switch is pressed, the unit
beeps once, which means the start of this operation.

When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:

Room
temperature

Above 23oC

o

Below 23

Designated
temperature

26

C 23oC

Timer

Fan

speed

AUTO

AUTO

Operation

mode

COOL

HEAT

mode

o

C

No

No

emergency

operation switch

Pi

It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.

Test operation:

Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room temperature

is below 16

Continue to press the test operation

switch for more than 5 seconds.After

you hear two beeps, release your finger

from the switch: the cooling operation

starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor
unit will run in high speed.

o

C, do not use it in the normal operation.

test operation

switch

Pi

Pi

Air Flow Direction Adjustment

1.Status display of air flow

COOL/DRY:

2.Left and right air flow adjustment

Move the vertical blade by a knob on air
to adjust left and right direction referring to the
figure below.

(manual)

conditioner

2

Operation

Mode

AUTO

COOL

DRY

HEAT

FAN

Remote

Controller

Note

Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according to

room temperature. When FAN is set to AUTO the air
conditioner automatically adjusts the fan speed according
to room temperature.

In DRY mode , when room temperature becomes lower

than temp.setting+2

speed regardless of FAN setting.

In HEAT mode, warm air will blow out after a short

period of the time due to cold-draft prevention function.

When FAN is set to AUTO, the air conditioner automatically

adjusts the fan speed according to room temperature.

In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in

FAN mode. And temp. setting is disabled. In FAN mode,

sleep operation is not available.

o

C, unit will run intermittently at LOW

FAN mode, AUTO is not available in

3D

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur
at air outlet if all vertical louvers are

right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY

otherwise, condensate water might occur.

Note:

When restart after remote turning off, the remote

controller will automatically

return to the previous

set swing position.

adjusted to left or

mode ,