Haier HSU-12HVE03-R2 User Manual

HSU-07HV03/R2(DB) HSU-09HV03/R2(DB)

HSU-12HVE03/R2(DB) HSU-18HVE03/R2(DB) HSU-22HVE03/R2(DB)

No, 0010503017

Contents

Cautions Parts and functions Operation

Maintenance Trouble shooting

-5

6-8

-21

22-26

Cautions

Disposal of the old air conditioner

Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled .Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.

Safety Instructions and Warnings

Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly, operation and maintenance of the air conditioner.

The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction.

Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.

Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.

Disposal of the packaging of your new air conditioner

All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.

The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads

contain no fluorochloric hydrocarbon.

All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.

Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.

Installation shall be done by professional people, don't install unit by yourself.

For the purpose of the safety,the air conditioner must be properly grounded in accordance with specifications.

Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.

Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.

Cautions

Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver.

Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.

Specifications

The refrigerating circuit is leak-proof.

The machine is adaptive in following situation

1.Applicable ambient temperature range:

32oC/23oC 18oC/14oC

43oC/26oC 18oC

Cooling

Indoor

Outdoor

Maximum:D.B/W.B Minimum:D.B/W.B

Maximum:D.B/W.B Minimum:D.B

7. The appliance is not intended for use by young children or infirm persons without supervision.

8. Young children should be supervised to ensure that they do not play with the applience.

9.Please employ the proper power plug, which fit into the power supply cord.

10 .The power plug and connecting cable must have acquired the local attestation.

11.In order to protect the units,please turn off the A/C first, and at least 30 seconds later, cutting off the power.

Heating

Indoor

Outdoor

Maximum:D.B Minimum:D.B

Maximum:D.B/W.B Minimum:D.B/W.B

27oC 15oC

24oC/18oC

-7oC

2. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.

3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is broken,change it with the type of T.25A/250V

4. The wiring method should be in line with the local wiring standard.

5. After installation, the power plug should be easily reached.

6. The waste battery should be disposed properly.

Cautions

Safety Instruction

Please read the following Safety Instructions carefully prior to use.

The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.

Installation

WARNING

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.

lnstallation in a inadequate place may cause accidents. Do not install in the following place.

CAUTION

Connect the earth cable.

Do not install in the place where there is any possibility of inflammable gas leakage around the unit.

Do not get the unit exposed to vapor or oil steam.

Check proper installation of the drainage securely

earthing

PROHIBITION PROHIBITION

STRICT ENFORCEMENT

Cautions

When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.

WARNING

Use an exclusive power source with a circuit breaker

OFF

Connect power supply cord to the outlet completely

STRICT

ENFORCEMENT

Do not use power supply cord in a bundle.

PROHIBITION

Do not start or stop the operation by disconnecting the power supply cord and so on.

PROHIBITION

STRICT

ENFORCEMENT

Use the proper voltage

STRICT

ENFORCEMENT

Take care not to damage

the power supply cord.

PROHIBITION

Do not channel the air flow directly at people, especially at infants or the aged.

PROHIBITION

Do not use power supply cord

extended or connected in halfway

PROHIBITION

Do not insert objects into the air inlet or outlet.

PROHIBITION

Do not try to repair or reconstruct by yourself.

Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.

PROHIBITION

Do not install the unit near a fireplace or other heating apparatus.

PROHIBITION

Do not place animals or plants in the direct path of the air flow

PROHIBITION

CAUTION

Take fresh air occasionally especially when gas appliance is running at the same time.

STRICT

ENFORCEMENT

Check good condition of the installation stand

PROHIBITION

Do not place any objects on or climb on the unit.

PROHIBITION

Do not operate the switch with wet hand.

PROHIBITION

Do not pour water onto the unit for cleaning

PROHIBITION

Do not place flower vase or water containers on the top of the unit.

PROHIBITION

Parts and Functions

Indoor unit

Display board

Inlet

Air Purifying Filter

(inside)

Inlet grille

Vertical flap (adjust up and down air flow. Don't adjust it manually)

Horizontal louver

(adjust left and right air flow)

For 18k 22k unit, the power plug is on the outdoor unit

Outdoor unit

Outlet Air filter(inside)

Anion generator

(inside)

Power plug

HSU-07HV03/R2(DB) HSU-09HV03/R2(DB) HSU-12HVE03/R2(DB)

OUTLET CONNECTING PIPING AND ELECTRICAL WIRING

INLET DRAIN HOSE

HSU-18HVE03/R2(DB) HSU-22HVE03/R2(DB)

Parts and Functions

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

23 24

31 32

19 1631 1712 24

9. HEALTH AIRFLOW button

Used to set the health airflow mode.

10. HEALTH button

Used to set healthy operation.

11. ON/OFF button

Used for unit start and stop.

12. TIMER ON display

13. FAN SPEED display

LOW HI

MED AUTO

14. LOCK display

15. SWING UP/DOWN display

16. SLEEP display

17. HEALTH display

18.FRESH AIR display

19. Operation mode display

Operation mode

Remote controller

Display board

AUTO HEAT FANCOOL DRY

1. LOCK

Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears.

2.LIGHT button

Control the lightening and extinguishing of the indoor LED display board.

3.CODE

Used to select CODE A or B with a press,A or B will be displayed on LCD. Please select A without special explanation.

4. TIMER button

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF.

5. CLOCK button

Used to set correct time.

6. SLEEP button

Used to select sleep mode.

7. MODE button

AUTO COOL DRY FAN HEAT

8. HOUR button

Used to set clock and timer setting.

20.Singal sending display

21. POWER/SOFT display

22. Left/right air flow display

23. TEMP display

Remote controller: to display the TEMP. setting.

24. TIMER OFF display

25. CLOCK display

26. TEMP button

Used to select your desired temperature.

27. FAN button

Used to select fan speed: LOW,MED, HI, AUTO.

28. SWING UP/DOWN button

Used to select up or down air sending direction.

29. SWING LEFT/RIGHT button

Used to select left/right air flow.

30.

FRESH

button

Use to set fresh air function.

31. SET button

Used to confirm timer and clock settings.

32. POWER/SOFT button

Use to set power/soft function.

33. RESET

When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.

NOTE:(1) The following functions and related displays are not available:

(2) Cooling only unit do not have functions and displays related with heating.

18 30

Parts and Functions

Clock Set

When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:

1. Press CLOCK button,"AM" or "PM" flashes.

2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly.

3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.

Remote controller's operation

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

Don't throw or knock the remoter controller.

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated right 2 R-03 (7#) batteries

Remove the battery cover: Slightly press" "area and push down the cover

as illustrated.

Load the battery: Be sure that the loading is in line with the "+" / "-".

request as illustrated on the bottom of the case. Put on the cover again.

Confirmation indicator: After pressing power ON/OFF, if no display, reload the batteries.

Note:

Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.

Used two new same-typed batteries when loading.

If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.

Hint:

Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.

Operation

HEALTH operation

Remote controller

TEMP

1.Unit start

Press on/off button (" ") on the remote controller, unit starts.

2.Health anion function

Press HEALTH button. For each press, is displayed.

Air conditioner starts health anion function operation.

For twice press, disappears,the operation stops.

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

When indoor fan motor is running, it has healthy process function. (It's available under any mode)

BRIEF INTRODUCTION TO HEALTH ANION FUCTION

The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.

Operation

Auto Operation

Remote controller

1. Unit start

2.Select operation mode

Press on/off button (" ") on the remote controller, unit starts.

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

AUTO COOL DRY FAN HEAT

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

Then

On the displaying board,colorful displaying bar will be white.

Select Auto operation

3.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

LOW

MED

AUTO

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

4.Unit stop

Press on/off button (" "), the unit stops. About Auto Operation

Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature.

Operation

Cool Operation

1. Unit start

Remote controller

Press on/off button (" ") on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

AUTO

COOL DRY FAN HEAT

Then Select COOL operation

On the displaying board,colorful displaying bar will be blue.

3.Select temp.setting

Press TEMP. button

Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase rapidly

Every time the button is pressed, temp.setting decrease 1oC,if kept depressed, it will decrease rapidly

Select a desired temperature.

4.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

LOW

MED

AUTO

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

5.Unit stop

Press on/off button (" "), the unit stops.

Operation

Dry Operation

1. Unit start

Remote controller

2.Select operation mode

Press on/off button (" ") on the remote controller, unit starts.

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

AUTO

COOL DRY FAN HEAT

Then Select DRY operation

On the displaying board,colorful displaying bar will be light blue

3.Select temp.setting

Press TEMP. button

Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase rapidly

Every time the button is pressed, temp.setting decrease 1oC,if kept depressed, it will decrease rapidly

Select a desired temperature.

4.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

COOL operation starts when room temp.is higher than temp.setting.

Temp.setting+2oC Temp.setting

On reaching temp.setting +2oC unit will run in mild DRY mode.

Ultra-low air flow

LOW

MED

AUTO

Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp.setting+2oC,unit will run intermittently at LOW speed regardless of FAN setting.

5.Unit stop

Press on/off button (" "), the unit stops.

Operation

Fan Operation

1. Unit start

Remote controller

2.Select operation mode

Press on/off button (" ") on the remote controller, unit starts.

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

AUTO

COOL DRY FAN HEAT

Then Select FAN operation

On the displaying board,colorful displaying bar will be pink.

3.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

LOW

MED

4.Unit stop

Press on/off button(" "), the unit stops.

About FAN operation

In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled. In FAN mode,SLEEP and POWER/SOFT operation is not available.

Operation

Heat Operation

1. Unit start

Remote controller

2.Select operation mode

Press on/off button (" ") on the remote controller, unit starts.

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

TEMP

HEALTH FAN

SWING

H.AIR.

MODE

FRESHSLEEP

CLOCK

TIMER

LOCK RESETLIGHT

SET

CODE

AUTO

COOL DRY FAN HEAT

Then Select HEAT operation

On the displaying board,colorful displaying bar will be red

3.Select temp.setting

Press TEMP. button

Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase rapidly

Every time the button is pressed, temp.setting decrease 1oC,if kept depressed, it will decrease rapidly

Select a desired temperature.

4.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

LOW

MED

AUTO

Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function.

When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

5.Unit stop

Press on/off button (" "), the unit stops.

+ 35 hidden pages