Haier HSU-12HVD03/R2, HSU-09HVD03-R2 User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-09HVd03/R2(SDB) HSU-12HVd03/R2(SDB)

Contents

CAUTIONS

PARTS AND FUNCTIONS OPERATION

MAINTENANCE

TROUBLE SHOOTING

1 2

3 6 7

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010515053

Parts and Functions

Indoor Unit



Inlet

Inlet grille

Air purifying Filter(inside)

Anion generator

(inside)

Horizontal flap

(adjust up and down air flow Don't adjust it manually)

Display board

Vertical blade

(adjust left and

right air flow)

Please be subject to the actual produce purchased the above picture is just from your reference



Display board







Singal receiver hole



AUTO display





COOL display





Dry display



Ambient temp.display



When receiving the remote control signal,

display the set temperature and in the rest

time the room temperature is displayed and

this room temperature is only for reference.









TIMER OFF display

TIMER ON display SLEEP display



HEAT display

HEALTH display





(If the unit which you purchased

has healthy function,follow it.

If not,please ignore.)



FRESH AIR display







Outdoor Unit

Outlet



Remote controller

10. ON/OFF button

11. TIMER ON display

. FAN SPEED display

LOW HI

MED AUTO

13. LOCK display

14. SWING UP/DOWN display

15. SLEEP display

16. HEALTH display

17.FRESH AIR display

18. Operation mode display

FRESH

STERILIZE

1.CODE

Used to select CODE A or B with a press, A or B will be displayed on LCD. Please select A without special explanation.

2.RESET

When the remote controller appears abnormal, use a sharp pointed article to

press this button to reset the remote controller normal.

3.LIGHT button

Control the lightening and extinguishing of the indoor LED display board.

4. TIMER button

5. CLOCK button

6. SLEEP button

7. MODE button

8. HOUR button

9. HEALTH button

NOTE : The following functions andrelated displays are not available: 1

Operation m ode AU T O H E A T F A NCOOL DRY

Remotecontroller

Display board

19.Singal sending display

20.UV light degerming function display

21. Left/right air flow display

22. TEMP display

23. TIMER OFF display

24. TIMER/SLEEP display

25. TEMP button

26. FAN button

27. HEALTH AIRFLOW button

28. SWING UP/DOWN button

29. SWING LEFT/RIGHT button FRESH

30.

31. SET button

32. STERILIZE button

33. LOCK

34.Ambient temp.display

button

Used to lock buttons and LCD display.If pressed,the other buttons will be disabled and the lock condition display appears. Press it once again,lock will be canceled and lock condition display disappears.

When receiving the remote control signal, display the set temperatrue and in the rest time the room temperature is displayed and this room temperature is only for reference.

Loading of the battery

OUTLET

CONNECTING PIPING

AND ELECTRICAL WIRING

DRAIN HOSE

INLET



Please be subject to the actual produce purchased the above picture is just from your reference

Clock set

Press CLOCK button, "AM" or "PM" flashes.

Press or to set correct time. Each press

or decrease 1min. If the

change quickly.

After time setting is confirmed,press SET,

button is kept pressed,time will

"AM "and "PM" stop flashing,while clock starts working.

will increase

STERILIZE

Remove the battery cover;





Load the batteries as illustrated.

2 R-03 batteries, resetting key



(cylinder);

Be sure that the loading



Load the battery,then put on the cover again.

Note:

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-sta rted type fluorescent lamp or change- over

type fluorescent lamp or room, the recei so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation, please

remove the batteries and

Hint:

Remove the batteries in case unit won't be in usage for a long period.

If there are any display

ver is apt to be disturbed in receiving

is in line with the

wireless telephone is installed in the

Please change batteries.

reload several minutes later.

after taking-out, just need to press reset key.

" + "/"-";

the signals,

Operation

Base Operation

Remote controller

)5(6+

32:(562)7

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

AUTO COOL DRY FAN HEAT

3.Select temp.setting

Press button

Every time the button is pressed, temp.setting increase 1 rapidly

Every time the button is pressed, temp.setting decrease 1 decrease rapidly

Select a desired temperature.

4.Fan speed selection

Press FAN button. For each press, fan speed changes as Remote controller:

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

Operation

Mode

AUTO

COOL

DRY

HEAT

FAN



follows:

Remote

Controller

C,if kept depressed, it will increase

C,if kept depressed, it will

LOW

MED

Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation

according to room temperature. to AUTO, the air conditioner

the fan speed according to room

In DRY mode , when room temperature becomes lower than temp.setting+2

intermittently at LOW speed regardless of FAN

setting.

In FAN operation mode , the unit will not operate in COOL or AUTO is not available in setting is disabled. In FAN mode, sleep operation

is not available.

Note

HEAT mode but only in

FAN mode.

AUTO

When FAN is set

automatically adjusts

temperature.

C, unit will run

FAN mode ,

And temp.

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective or lost.

When the emergency ope pressed,the" Pi "sound is heard once means

the start of this operation.

In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature.

Tem p e ra t ur e

ABOVE 23

BELOW 23

It is not possible to operate in dry mode.

Operation

COOLING

HEATING

mode

ration switch is

Designated temperature

, which

Ti me r mode

Air flow

AUTOMATIC

Test operation:

Test ope ration switch is the same as emergency switch.

Use this switch in the test operation when the room

temperature is below 16 normal operation.

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,

your finger from the switch: the cooling

operation starts with the air flow speed "Hi".

After 3 0 minutes, test operation ends automatically.

C, do not use it in the

release

Air Flow Direction Adjustm

1.Status display of air sending

Vertical flap

Pos.1

Pos.4

2.Left and right air flow adjustment

For each press of button, remote controller displays as follows :

remote controller:

Pos. 1

Pos. 5

Cautions:

It is advisable not to keep vertical flap at

for a long time in COOL

condensate

When humidity is high, condensate water

air outlet if all horizontal

Unit won't restart until 3 minutes have

system protection.

cooling only unit.

Pos.2

Pos.5

Pos. 2

Pos. 6

Pos.3

Pos.6

Pos. 3

Pos. 7

or DRY mode, otherwise,

water might occur.

louvers are adjusted to left or right.

HEAT mode is not available on

(Auto swing)

(manual)

Pos. 4

Pos. 8

downward position

might occur at

elapsed, due to

+ 5 hidden pages