Haier HSU-12HT03-R2, HSU-10HT03-R2 User Manual

SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-10HM03/R2(DB) HSU-12HM03/R2(DB) HSU-10HT03/R2(DB) HSU-12HT03/R2(DB)
Please read this operation manual before using the air conditioner.
No.
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of entrapment.
It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner be recycled. Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get prior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.
child
can
damaged
Safety Instructions and Warnings
Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly , operation and maintenance of the air conditioner.
The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction.
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Installation shall be done by professional people, don't install unit by yourself.
Disposal of the packaging of your new air conditioner
All the packaging materials employed in package of your new air conditioner may disposed without any danger to the environment.
The cardboard box may be broken or cut smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon.
All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.
Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.
the
be
into
For the purpose of the safety,the air conditioner must be properly grounded in accordance with specifications.
Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.
Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items , crushing or twisting any tubes , or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes , it may result in serious eye injuries.
1
Cautions
Do not obstruct or cover the ventilation grille of the air conditioner. Do not put fingers or any other things into the inlet/outlet and swing louver.
Do not allow children to play with the air conditioner. In no case should children be allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
The machine is adaptive in following situation
1. Applicable ambient temperature range:
Indoor
Cooling
Outdoor
Indoor
Heating
Outdoor
Maximum: D.B/W.B 32∞C / 23∞C Minimum: D.B/W.B 18∞C / 14∞C
Maximum: D.B/W.B 43∞C / 26∞C
Minimum: D.B 18∞C Maximum: D.B 27∞C
Minimum: D.B 15∞C Maximum: D.B/W.B 24∞C / 18∞C
Minimum: D.B/W.B -15∞C
7. The appliance is not intended for use by young children or infirm persons without supervision.
8. Young children should be supervised to ensure that they do not play with the applience.
9.Please employ the proper power plug, which fit into the power supply cord.
10.The power plug and connecting cable must have acquired the local attestation.
11.If the fuse of outdoor unit on PC board is broken, please change them with the corresponding type of T.1.0A/250V, T.3.15A/250V,T.25A/250V.
2. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.
3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V.
4. The wiring method should be in line with the local wiring standard.
5. After installation, the power plug should be easily reached.
6. The waste battery should be disposed properly.
2
Cautions
Safety Instruction
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth cable.
earthing
Do not install in the place where there is any possibility of inflammable gas leakage around the unit.
PROHIBITION PROHIBITION
Do not get the unit exposed to vapor or oil steam.
3
Check proper installation of the drainage securely
STRICT ENFORCEMENT
Cautions
When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.
WARNING
Use an exclusive power source with a circuit breaker
OFF
Connect power supply cord to the outlet completely
STRICT
ENFORCEMENT
Do not use power supply cord in a bundle.
PROHIBITION
Do not start or stop the operation by disconnecting the power supply cord and so on.
PROHIBITION
Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.
STRICT
ENFORCEMENT
Use the proper voltage
STRICT
ENFORCEMENT
Take care not to damage
the power supply cord.
PROHIBITION
Do not channel the air flow directly at people, especially at infants or the aged.
PROHIBITION
CAUTION
Take fresh air occasionally especially when gas appliance is running at the same time.
Do not use power supply cord
extended or connected in halfway
PROHIBITION
Do not insert objects into the air inlet or outlet.
PROHIBITION
Do not try to repair or reconstruct by yourself.
Do not operate the switch with wet hand.
PROHIBITION
Do not install the unit near a fireplace or other heating apparatus.
PROHIBITION
Do not place animals or plants in the direct path of the air flow
PROHIBITION
STRICT
ENFORCEMENT
Check good condition of the installation stand
PROHIBITION
Do not place any objects on or climb on the unit.
PROHIBITION
4
PROHIBITION
Do not pour water onto the unit for cleaning
PROHIBITION
Do not place flower vase or water containers on the top of the unit.
PROHIBITION
Parts and Functions
Indoor unit
Signal receiving window
Inlet grille
Air Purifying Filterr (inside)
Vertical louver
(Use remote controller to adjust up and down air flow. Donít adjust it manually)
Horizontal louver
(adjust left and right air flow)
Control panel
Operation indicator
Healthy operation indicator
Human sensing indicator
Light sensing receiver
Human sensor
Outlet
Air filter(inside)
Anion generator (inside)
Power plug
Timed operation indicator Sleep indicator
Power indicator Remote signal receiver
Outdoor unit
Connecting piping and electrical wiring
Inlet
Outlet
Drain hose
5
Parts and Functions
18 17
16 15 14
13 12 11
11 10
9 8 7
6 5
4 3
2
36
1
button(light sensing)
1.
It is to set light sensing function, which enables normal operation for strong indoor light (day) or sleeprunning mode for weak indoor light (night).
2.RESET
When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.
button
3.
It is to set human sensing function, which automatically gets standby if detecting no human activity for continuously 20 min, and automatically starts running upon re-detecting human activity.
4.TIMER button
Used to select TIMER ON, TIMER OFF,TIMER ON-OFF
5. CLOCK button
Used to set correct time.
6. SLEEP button
Used to select sleep mode.
7.MODE button
19 20
21 22
23
24
25
26
27 35
28
29 30 31
32 33
AUTO COOL DRY FAN HEAT
8.HOUR button
Used to set clock and timer setting
9.HEALTHY button
Used to set healthy operation.
10. ON/OFF button
Used for unit start and stop.
11. TIMER ON display
12. FAN SPEED diaplay
LOW
MED
HI
13. LOCK diaplay
14. SWING UP/DOWN diaplay
15. SLEEP diaplay
16. HEALTH diaplay diaplay
17. diaplay
18. diaplay
19.
20.SIGNAL SENDING diaplay
AUTO
21.POWER/SOFT diaplay
22.Left/right air flow display
34
23.TEMP display
Remote controller: to display the TEMP. setting
24. TIMER OFF display
25. CLOCK display
26.TEMP button
Used to select your desired temperature.
27.FAN button
Used to select fan speed: LO,MED, HI, AUTO.
28.SWING UP/DOWN button
Used to select up or down air sending direction.
29.SWING LEFT/RIGHT button
Used to select left/right air flow.
30.SET button
Used to confirm timer and clock settings.
31.POWER/SOFT button
32. button
Used to select nature air
33.LOCK
Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears.
34. LIGHT display
Only for the model with background lighting function.
35. HEALTH AIRFLOW button
Used to set the health airflow mode.
6
Parts and Functions
36. CODE
Used to select CODE A or B with a press,A or B will be displayed on LCD. please select A without special explanation
NOTE:
The following functions and related displays are nto available: CODE and LIGHT.
Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:
1. Press CLOCK button,"AM" or "PM" flashes.
2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly.
3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.
Remote controller's operation
When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well. Don't throw or knock the remoter controller. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless
telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the
distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated right. 2 R-03 (7#) batteries
Remove the battery cover: Slightly press" " area and push down the cover as illustrated.
Load the battery:
Be sure that the loading is in line with the "+" / "-" pole request as illustrated on the bottom of the case.
Put on the cover again.
Confirmation indicator: After pressing power ON/OFF, if no display, reload the batteries.
Note: Full display or unclear display during operation indicates the batteries have been used up. Please Used two new same-typed batteries when loading. If the remote controller can't run normally during operation, please remove the batteries and reload
Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display afte taking-out, just need to press reset key.
change batteries.
several minutes later.
r
7
Operation
HEALTH Operation
Remote Controller
1. Unit start Press ON/OFF the remote controller, unit starts.
2. Select operation mode Press HEALTH button. For each press, is displayed now the air copnditioner is operating the healthy function.
3. Unit stop Press HEALTH button, the health function stops.
BRIEF INTRODUCTION TO HEALTH OPERATION
The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
Note
When the fan in the indoor unit does not work, the health lamp lights up, but the anion generator does not release anion.
8
Operation
Auto Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO COOL DRY FAN HEAT
Then
3.Unit stop
Press ON/OFF button, the unit stops. About Auto Operation
Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature.
Select Auto operation
9
Operation
Cool Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
Then Select COOL operation
COOL DRY FAN HEAT
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will decrease rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
Air conditioner is running under dispalyed wind speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
MED
HI
5.Unit stop
Press ON/OFF button, the unit stops.
10
AUTO
Operation
Dry Operation
1. Unit start
Remote controller
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
COOL DRY FAN HEAT
Then Select DRY operation
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will decrease rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
Air conditioner is running under dispalyed wind speed. In DRY mode, when room temperature becomes 2OC higher than temp.setting,unit will run intermittently at LOW speed regardless of FAN setting.
AUT O
COOL operation starts when room temp.is higher than temp.setting.
Temp.setting+2oC Temp.setting
On reaching temp.setting +2oC unit will run in mild DRY mode.
Ultra-low air flow
5.Unit stop
Press ON/OFF button, the unit stops.
11
Operation
Fan Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
Then Select FAN operation
3.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
4.Unit stop
Press ON/OFF button, the unit stops.
About FAN operation
In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled. In FAN mode,SLEEP operation is not available.
COOL DRY FAN HEAT
LOW
MED
HI
12
Operation
Heat Operation
Remote controller
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
Then Select HEAT operation
COOL DRY FAN HEAT
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly
Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will decrease rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function.
HI
AUTO
5.Unit stop
Press ON/OFF button, the unit stops. Regarding the ambient temperature display during the heating operation.
In defrosting, the indoor temperature value displayed may be reduced due to the dropping of cooling air of the evaporator of indoor unit under cooling mode. It is mormal phenomenon.
13
Operation
Air Flow Direction Adjustment
1.Status display of air sending diretion
Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
(Auot swing)
Horizontal louvers
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
Pos.7
Pos.8
2.Up and down air flow direction
For each press of button, air flow direction on remote controller displays as follows according to different operation modes:
COOL/DRY/FAN remote controller:
:
HEAT
remote controller:
:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.6
Pos.5 Pos.4 Pos.3 Pos.2 Pos.1 Pos.6
AUTO
remote controller:
:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6
The vertical flap will swing according to the above positoins
3.Left and right air flow direction
For each press of button, remote controller displays as follows :
remote controller:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
The horizontal louvers will swing accroding to the above positions.
Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position.
14
Operation
Sleep Operation
Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. Operation Mode
1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will become 1OC higher than temp. setting. After another 1 hours, temp. rises by 1OC further. The unit will run for further 6 hours then stops. Temp. is higher than temp. setting so that room temperature won't be too Iow for your sleep.
Remote Controller
SLEEP operation starts SLEEP operation stops
Approx.6hrs
Rises 1OC
1 hr
Rises 1OC
1 hr
Temp.setting
In HEAT mode
2.
In COOL, DRY mode
Unit stop
1 hours after SLEEP mode starts, temp will become 2 OC lower than temp. setting. After another 1 hours, temp decrease by 2 OC further. After more another 3 hours, temp. rises by 1OC further. The unit will run for further 3 hours then stops. Temp. is lower than temp. setting so that room temperature won't be too high for your sleep.
Temp.setting
SLEEP operation starts
In AUTO mode
3.
1 hr
Decreases 2OC
1 hr
Decreases 2OC
3 hrs
In HEAT mode
Unit stop
3 hrs
Rises 1OC
SLEEP operation stops
The unit operates in corresponding sleep mode adapted to the automatically selected operation mode.
4. In FAN mode It has no SLEEP function.
5.Set the wind speed change when sleeping If the wind speed is high or middle before
setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change.
15
Operation
Timer On/Off Operation
Remote Controller
Set clock correctly before starting TIMER operation.
1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD.
2. Timer mode selection
Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash.
3.Time setting Press HOUR button.
Every time the button is pressed, time setting increases l min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases l min, if kept depressed, it will decrease rapidlly. It can be adjusted within 24 hours.
4.Confirming your setting
After setting correct time, press SET button to confirm " "or" "on the remote controller stops flashing. Time displayed: Unit starts or stops at x hour x min. (TIMER ON or TIMER OFF).
5.Cancel TIMER mode Just press TIMER button several times until TIMER
mode disappears.
Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one.
16
Operation
Timer On-Off Operation
Set clock correctly before starting TIMER operation.
Remote Controller
1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD.
2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:
Then select your desired TIMER mode (TIMER ON - OFF). " "will flash.
3.Time setting
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
Press HOUR button. Every time the button is pressed, time setting increases l min, if kept depressed, it will increase rapidly. Every time the button is pressed, time settingdecreases l min, if kept depressed, it will decrease rapidly. It can be adjusted within 24 hours.
4.Timer confirming for TIMER ON
After setting correct time, press TIMER button to confirm " " on the remote controller stops flashing. " " starts flashing. Time displayed: Unit starts or stops at x hour x min.
5.Time setting for TIMER OFF
Just press HOUR button ,follow the same procedure in "Time setting for TIMER ON"
6.Time confirming for TIMER OFF
After time setting,press SET button to confirm. " " on the remote controller stops blinking. Time displayed:Unit stops at x hour x min.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved.
17
Operation
POWER/SOFT Operation
POWER Operation
Remote Controller
When you need rapid heating or cooling, you can use this function. Selecting of POWER operation
Press POWER/SOFT button. Every time the button is pressed,display changes as follows:
POWER
Stop the display at " ". In POWER operation status:
In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting.
To cancel POWER operation Press POWER/SOFT button twice, POWER/SOFT disappears.
SOFT
BLANK
SOFT Operation
You can use this function when silence is needed for rest or reading. Selecting of SOFT operation
Press POWER/SOFT button. Every time the button is pressed, display changes as follows:
POWER
SOFT
BLANK
Stop the display at " ". In SOFT operation mode, fan speed automatically takes "LO". To cancel SOFT operation
Press POWER/SOFT button once, POWER/SOFT disappears. Hint
During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm.
18
Operation
Health airflow Operation
Remote Controller
1.Press ON/OFF to starting
The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions.
2.The setting of health airflow function
1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air condit­ioner are closed and the airflow is blown horizontally from the above inlet and outlet grills. Avoid the strong airflow blows direct to the body.
2).Press the button of health airflow again, appears on the display. The above inlet and outlet grills of the air cond­itioner are closed and the airflow is blown vertically from the nether inlet and outlet grills. Avoid the strong airflow blows direct to the body.
3.The cancel of the health airflow function
Press the button of health airflow again, both the inlet and outlet grills of the air conditioner are opened, and the unit goes on working under the condition before the setting of health airflow function. After stopping, the outlet grille will close automatically. Notice: Cannot pull direct the outlet grille by hand. Otherwise, the grille will run incorrectly. If the grille is not run correctly, stop for a minute and then start, adjusting by remote controller.
Note: 1 .After setting the health airflow function, the position of inlet and outlet grills is fixed.
2.In heating, it is better to select the mode.
3.In cooling, it is better to select the mode.
4.In cooling and dry, using the air conditioner for a long time under the high air humidity, a phenomenon falling drips of water occurs at the outlet grille .
5.Select the appropriate fan direction according to the actual conditions.
19
Operation
1.Unit start After switching on and setting running mode,the LCD
screen will display the operating conditions.
2.Selecting natural air function
Press key, the remote controller displays a symbol of and natural air function actuates. Press key again to cancel the displayed symbol of and the natural air function. After selecting natural air function, fan speed and left/right air direction are set as AUTO whereas after cancellation thereof, fan speed automatically resumes the status before selecting natural air function. After actuating natural air function, pressing STRONG/SOFT key will enable strong/soft running, and the remote controller displays strong/soft symbol, natural air symbol disappears and natural air function is cancelled. When strong/soft running is exited, it resumes to natural air mode. In the strong/soft mode, key is disabled.
3.Selecting human sensing function Press key, the remote controller displays symbol and
human sensing function starts; pressing this key once more will get the symbol disappear and human sensing function cancelled. After selecting human sensing function, if setting sleep mode, human sensing function will automatically cancels, and doesn't resume upon sleep mode is removed. During sleep mode, human sensing function is disabled.
4.Selecting light sensing function Press key, the remote controller displays symbol and light sensing function starts; pressing this key once more will get the symbol disappear and light sensing function cancelled. Light sensing function could be set in every running mode (excluding FAN mode) and reserved during mode changing, except that light sensing function will be automatically cancelled. when changing to FAN mode and resume upon changing to other modes. After selecting light sensing function, sleep function is unavailable; while in sleep mode, pressing key will cancel sleep function. If restarting the unit after switching off,light sensing function needs re-setting.
5.Unit stop Press ON/OFF key to turn off the unit.
20
Operation
About natural air function
Natural air means that the air conditioner runs with analog natural airflow and automatically changes air speed to avoid human discomfort due to long exposure to strong wind.
About human sensing function
Human sensing function is to detect indoor human activity with a human sensor. After human sensing is actuated, if the unit keep detecting no human activity for 20 min, it will automatically enters standby (monitor) status, during which the unit will automatically start and resume operation if sensing human activity.
About light sensing function
Light sensing function is to detect indoor light intensity with a photosensor. After
setting light sensing function, if darkness is continuously detected for 2 min, the unit will automatically change to sleep mode; the main machine will remain current operation conditions if darkness remains after 8 hrs. Anytime brightness is detected for 10 min, the unit will quit sleep mode and resume operation conditions before sleep running. Light sensing and human sensing could be actuated simultaneously, while human sensing is unavailable during light sensing.
About intelligent operation
During intelligent operation, the indoor human activity or light intensity is sensed through an intelligent sensor (human sensor, photosensor), and the unit runs as follows according to the room conditions:
Human sensor
Photosensor
Room conditions
Running mode
(sensed)persons
(sensed)dark (sensed)bright
Night and with shading curtain
Sleep
continue ten minutes continue two minutes
Day or night lamp light
Resume operation standby
(sensed)no persons
continue twenty minutes
in twenty minutes
1.At high ambient temperature, the human sensor may detect inaccurately or invalidly due to thermal airflow.
2.Please notice that itíll enter sleep mode when turning off the room lamps, during which sleep running continues even if people leave the room.
3.If light sensing and human sensing are both selected, when the photosensor detects ìdarkî, the air conditioner wonít change its running mode even the human sensor detects human activity.
4.The human sensor could detect animals such as dogs and cats as well as heat sources e.g. heaters and electric cookers.
21
Operation
5.The human sensor could also detect strong electromagnetic waves such as radios and mob phones.
6.Do not place objects infrared rays couldnít penetrate within the human sensorís perception range.
Note: If intelligent operation doesnít meet your desire, e.g. slight human activity couldnít
be sensed, it shall be cancelled.
About installing position of air conditioner (indoor unit) and sensible zone of human sensor:
The dashed area shown in the figure is the sensible zone and the blank area is the dead
zone. (Taking a 12 m2 room as example)
Horizontal direction as shown follows:
about 2.2m
bed
chair
Sensible zone
desk
sofa
about 3.6m
bed
air conditioner
o
100
about 1.4m
air conditioner
o
100
chair
about 2.2m
o
65
air conditioner
bed
Sensible zone
desk
sofa
about 3.6m
air conditioner
o
100
chair
Sensible zone
about 3.6m
desk
sofa
about 0.7m
Sensible zone
about 3.6m
The horizontal zone where human activity could be detected by the human sensor is about 100o. Sensible zones differ according to installation position and room space. Please refer to installation examples to select installation position according to room design.
Vertical direction
As shown in the figure, the sensible zone in vertical direction crosses downward 60o. The sensing distance is 3.5-5 m.
22
Operation
Emergency and Test Operation
Emergency operation:
Use this operation only when the remote controller is defective or lost.
When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation.
In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature.
Temperature
ABOVE 23OC BELOW 23OC
It is not possible to operate in dry mode.
Operation mode
COOLING HEATING
Designated temperature
26OC 23OC
Timer mode
NO NO
Air flow
AUTOMATIC AUTOMATIC
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room temperature is below 16OC, do not use it in the normal operation.
Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".
After 30 minutes, test operation ends automatically.
Removal of the restriction of emergency or test operation
Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated.
When the remote controller is manipulated, it gets the system back to the normal operation mode.
23
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room temperature
Proper temperature
Close doors and windows during operation
During cooling operation prevent the penetration of direct sunlight with curtain or blind
Do not block the air inlet or outlet
Use the timer effectively
If the unit is not to be used for a long time, turn off the power supply main switch.
OFF
Use the louvers effectively
24
Maintenance
For Smart Use of The Air Conditioner
WARNING
Before maintenance,be sure to turn off the system and the ciruit breaker.
Remote Controller
Do not use water, wipe the controller with a dry cloth.Do not use glass cleaner or chemical cloth.
Do not use the following for cleaning
Gasoline,benzine, thinner or cleanser may damage the coating of the unit.
Air Filter cleaning
Open the inlet grille by pulling it upward.
Indoor Body
Wipe the air conditioner by using a soft and dry cloth.For serious stains,use a neutral detergent diluted with water.Wring the water out of the cloth before wiping.then wipe off the detergent completely.
Hot water over 40OC(104OC) may cause discoloring or deformation.
Remove the filter.
Push up the filter's center tab slightly unitl it is released from the stopper, and remove the fileter downward.
Clean the filter.
Use a vacuun cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.
Attach the filter.
Attach the filter correctly so that the "FRONT" indication is facing to the front.Make sure that the filter is completely fixed behind the stopper.If the right and left filters are not attached correctly, that may cause defects.
Close the inlet grille.
25
Once every two weeks
Maintenance
Replancement of Air Purifying Filter
1.Open the lnlet Grille
Open the inlet grille by pushing each ends of the inlet grille upward.(use thumbs to push up)
2.Detach the standard air filter
Slide the knob slightly upward to release the filter, then withdraw it.
3.Detach old Air Purifying Filter
Air Purifying Filter
4.Attach old Air Purifying Filter
Put air purifying filter appliances into the right and left filter frames as white side face to the front.
Air Purifying Filter
5.Attach the standard air filter
(Necessary installation)
6.Close the Inlet Grille
Close the Grille surely
NOTE:
Please replace the air Purifying Filter in3-6 months as standard. Stuffed filter are not usable even washing.Please purchase new one at sales shop
26
Maintenance
To Keep Your Air conditioner in Good Condition after Season.
Operate in cooling mode for 2-3 hours.
To prevent breeding mold or bad smell, be sure to operate at the desinnated temperature or 30OC,cooling mode and High speed fan mode for 2-3 hours.
Put off the power supply cord.
Cleaning the body.
Take out the batteries from the wireless remote controller.
27
Maintenance
Before Setting in High season
Cleaning the standard air filter.
Operation without filter may cause troubles.Be sure to attach both right and left filters prior to the operation. Each of them are of different shapes.
Connecting the earthing cable.
Caution
Incomplete earthing may cause an electric shock.
Do not block the air inlet or outlet.
Plug-in
Caution
After brush away dust at the plug, insert the plug of the power supply cord into the outlet completely.In case of suing exclusive circuit breaker,switch on the circuit breaker.
EARTHIN G
NO WET HAND
28
Trouble shooting
Before asking for service, check the following first.
Normal Perfromance inspection
Phenomenon
The system does not restart immediately.
Noise is heard:
Smells are generated.
Mist or steam are blown out.
Cause or check points
When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner.
During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system.) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes. Should there be a big noise from air flow in unit operation, air filter may be too dirty.
This is because the system circulates smells from the interior air such as the smell of furniture, cigarettes.
During COOL or DRY operation, indoor unit may blow out mist. This is due to the sudden cooling of indoor air.
Multiple check
Does not work at all.
Poor cooling
Is power plug inserted? Is there a power failure? Is fuse blown out?
Is the air filter dirty? Normally it should be cleaned every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(Use curtain) Are there too much heat sources or too many people in the room during cooling operation?
29
Loading...