Haier HSU-12HQA03-R2-DB User Manual

OPERATION MANUAL

HSU-12HQA03/R2(DB)

Please read this operation manual before using the air conditioner

0010538206

Contents

Parts and functions Operation Maintenance

Cautions Trouble shooting

2 3

6 7

Parts and Functions

Indoor Unit

Inlet

Inlet grille

Nano-Aquo Generator （inside）

Outlet

Horizontal flap

(adjust up and down air flow

Don't adjust it manually)

Actual indoop unit may vary from the one shown

in the manual, according to the product purchased.

Display board

Aureole

Display mode，the aureole display different colour when setting different function

COOL: blue

AUTO: white

HEAT: red

DRY: cyan

TEMP display

FAN: yellow

Nano-Aquo

Outdoor Unit

Air Purifying Filter

generator

(inside)

Vertical blade

(adjust left and

right air fl

: green

Anion

ow)

Remote controller

9. ON/OFF button

10. TIMER ON display

11. FAN SPEED display

LOW HI

MED AUTO

12. LOCK displ

13. SWING display

14. SLEEP display

15. HEALTH display

16. Operation mode display

Operation mode

Remote controller

17.Singal sending display

RESET button

When the remote controller

appears abnormal,use a sharp pointed article to press this button to reset the remote controller controller normal.

2.LIGHT button

Control the lightening and extinguishing of the indoor LED display board.

3. TIMER button

4. CLOCK button

5. SLEEP button

6. MODE button

7. HOUR button

8. HEALTH button

The following functions and related displays are not available：

18. POWER/SOFT display

19. Left/right air flow display

20. TEMP display

21. TIMER OFF display

22. TIMER display

23. TEMP button

24. FAN SPEED button

25. HEALTH AIRFLOW button

26. SWING UP/DOWN button

27. SWING LEFT/RIGHT button

28. SET button

29. POWER/SOFT button

LOCK

If pressed, the other buttons will be disabled. Press it once again, lock will be cancelled.

31. CODE

Used to select CODE A or B with a press, A or B will be displayed on LCD. Please select A without special explanation.

AUTO

button

COOL DRY

HEAT

Loading of the battery

FAN

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Clock set

Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press

or decrease 1min. If the

change quickly.

"AM "and "PM" stop flashing,while clock starts working.

After time setting is confirmed,press SET,

button is kept pressed,time will

will increase

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

Load the battery,then put on the cover again.

Note:

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or room, the recei so the distance to the indoor unit should be sho

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation, please

remove the batteries and

Hint:

Remove the batteries in case unit won't be in usage for a long period.

If there are any display

ver is apt to be disturbed in receiving

is in line with th

wireless telephone is installed in the

Please change batteries.

reload several minutes later.

after taking-out, just need to press reset key.

e" + "/"-";

the signals,

rter.

Operation

Base Operation

Remote controller

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode changes as follows: Remote controller:

AUTO COOL DRY FAN HEAT

3.Select temp.setting

Press button

Every time the button is pressed, temp.setting increase 1 rapidly

Every time the button is pressed, temp.setting decrease 1 decrease rapidly

Select a desired temperature.

C,if kept depressed, it will increase

C,if kept depressed, it will

4.Fan speed selection

Press FAN button. For each press, fan speed changes as Remote controller:

follows:

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective or lost.

When the emergency operation switch is pressed,the" Pi "sound is heard once means

the start of this operation.

In this operation, the system automatically selects

operation modes

the according to the room temperature.

Room

temperature

ABOVE 24

BELOW 24

Room temperature

It is not possible to operate in dry mode.

ooling only uint）

BELOW 2

,cooling or fan or heat,

Operation mode

COOLING

HEAT

Designated temperature

Operation

mode

FAN

Designated temperature

, which

Timer

mode

AUTOMATIC

Air flow

AUTOMATIC

Timer mode

emergency operation switch

Air flow

AUTOMATIC

Test operation:

Test ope ration switch is the same as emergency switch.

Use this switch in the test operation when the room

temperature is below 16 normal operation.

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,

your finger from the switch: the cooling

operation starts with the air flow speed "Hi".

C, do not use it in the

release

test operation

switch

Air Flow Direction Adjustment

1.Status display of air flow

Vertical flap

Pos.1

Pos.2

Pos.3

LOW

MED

AUTO

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

Operation

Mode

AUTO

COOL

DRY

FAN

HEAT

Remote

Controller

Note

Under the mode of auto operation, air conditioner

will automatically select Cool or Heat operation according to room temperature. When FAN is set to AUTO, the air conditioner the fan speed according to room

In DRY mode, when room temperature becomes

lower than temp.setting+2 intermittently at LOW speed regardless of FAN setting.

In FAN operation mode , the unit will not operate in COOL or

HEAT mode but only in

AUTO is not available in setting is disabled. In FAN mode, sleep operation

is not available.

automatically adjusts

temperature.

C, unit will run

FAN mode ,

FAN mode.

And temp.

Pos.4

Pos.5

Pos.6

(Auto swing)

2.Left and right air flow adjustment

For each press of button, remote controller displays as follows :

remote controller:

Pos.1

Pos.5

Pos.2

Pos.6

Pos.3

Pos.7

Pos.4

Pos.8

Cautions:

When adjusting the flap by hand,turn off the unit. When humidity is high,condensate water might occur at air outlet if all vertical louvers are

right. It is advisable not to keep horizontal flap at downward

position for a long time in COOLor DRY otherwise, condensate water might occur.

Note:

When restart after remote turning off, the remote

controller will automatically

memorize the previous

set swing position.

adjusted to left or

mode ,

+ 11 hidden pages